TP-Link Router TL-WR941N User Manual

TL-R480TSMB Broadband Router User Guide  
 
65
4)  Static address assignment of DHCP server. 
5)  Web Service Port of the router. 
6)  Upgrade the firmware of the router (system will reboot automatically). 
7)  Restore the routers settings to factory default (system  will reboot automatically). 
4.13.6 Password 
Choose menu “ System Tools→Password ”, you can change the factor y default user name and 
password of the router in the next screen (shown in  Figure 4-71). After configuration, click the 
Save...

TL-R480TSMB Broadband Router User Guide  
 
66
 
Figure 4-72 
The router can keep logs of all traffic. You c an query the logs to find what happened to the router. 
Click the  Refresh button to refresh the logs. 
Click the  Clean All button to clean all the logs. 
4.13.8 Remote Management 
Choose menu “ Security→Remote Management ”, you can configure the Remote Management 
function on this screen (shown in  Figure 4-73). This feature allows you to manage your Router 
from a remote location v

ia the...

TL-R480TSMB Broadband Router User Guide  
 
67
1)  To access the router, you will type your routers WAN IP address into your browsers 
address (in IE) or Location (in Navigator) box , followed by a colon and the custom port 
number. For example, if your Routers WAN address is 202.96.12. 8, and the port number 
you use is 8080, please enter  http://202.96.12.8:8080 in your br
 owser. Later, you may be 
asked for the routers password. After succe ssfully entering the username and password, 
you will be...

TL-R480TSMB Broadband Router User Guide  
 
68
Packets The total amount of packets received and transmitted by the router Total Bytes The total amount of bytes received and transmitted by the router 
Packets The total amount of packets received and transmitted in the last “Packets 
Statistic interval” seconds 
Bytes The total amount of bytes received and transmitted in the last “Packets 
Statistic interval” seconds 
ICMP Tx The total amount of the ICMP packets  transmitted to WAN in the last 
“Packets...

TL-R480TSMB Broadband Router User Guide  
 
69
 
Figure 4-75 
¾  Destination IP -  the IP address which datagrams are sent to, such as- 202.96.134.188.   
¾ ID -  The number of ICMP datagrames to be sent.   
¾ Source Port - The port where datagrams are sent to, such as- 5000   
¾ Destination Port -  The datagrams distination port, such as-6000.   
¾ UDP Data -  The data carried when sent UDP  detect datagram, take care if in the UDP data 
exist character ., for example, 123.456, www.yahoo. com, the...

TL-R480TSMB Broadband Router User Guide  
 
70
considered to be a domain name, DNS datagram will be sent, at this time, no matter what the 
destination port is, the desti nation port in the sent datagram is  always 53. If not, it will be sent 
as a whole UDP datagram.   
¾  Detect Result -  The interval between sending datagram  and recving datagram, uint is ms.   
4.13.11 IP NAT Table 
Choose menu “ System Tools→IP NAT Table ”, you will see the IP NAT in the table below: 
 
Figure 4-76 
¾  Out Link -...

TL-R480TSMB Broadband Router User Guide  
 
71
 
Appendix A: Specifications 
General 
Standards and Protocols  IEEE 802.3, 802.3u 
TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP,HTTP,DNS
 
Safety & Emission 
FCC、CE 
Ports  One 10/100M Auto-Negotiation WAN RJ45 port. 
Four 10/100/1000M Auto-Negot
iation LAN RJ45 ports (Auto 
MDI/MDIX) 
One Console (RS232 DB9 Male) 
Cabling Type  10BASE-T: UTP category 3, 4,
 5 cable (maximum 100m) 
EIA/TIA-568 100 Ω STP (maximum 100m) 
100BASE-TX: UTP category 5, 5e cable (maximum...

TL-R480TSMB Broadband Router User Guide  
 
72
Appendix B: FAQ 
1.  How do I configure the router to access Internet by ADSL users? 
Step 1: First, configure the ADSL m odem in RFC1483 bridge model. 
Step 2:  Connect the Ethernet cable from your ADSL modem to the WAN port on the router. The 
telephone cord plugs into the Line port of the ADSL modem. 
Step 3:  Login to the router, click the menu  Network→WAN on the left of your browser. On the 
WAN screen, select “ PPPoE” for the type of WAN connection....

TL-R480TSMB Broadband Router User Guide  
 
73
2.  How do I configure the router to access Internet by Ethernet users? 
Step 1: Login to the router, click the menu  Network→WAN on the left of your browser, On the 
WAN screen, select “Dynamic IP ” for WAN Connection Type , and finish it by clicking 
Save. 
Step 2:  Some ISPs require that you register the MAC address of your adapter, which is 
connected to your cable or  DSL modem during installation. If your ISP requires MAC 
register, login to the...

TL-R480TSMB Broadband Router User Guide  
 
74
 
Figure B-4 
)  Note: 
Your opposite side should call your WAN IP, which is displayed on the “Status” page. 
Method two: Use DMZ Host 
Login to the router, click the menu  Forwarding→DMZ . On the DMZ screen, select “Enable”, and 
enter your IP address into the “DMZ Host IP  Address” field (using 192.168.1.102 as an example), 
then to click the  Save button.   
 
Figure B-5 
7.  I want to build a WEB Server on the LAN, what should I do? 
Because the WEB...