Toshiba Tdp Tw350uk Projector User Manual

							61
Operations
60
Projecting images stored in a memory PC card or USB memory (Continued)\
•[Interval]
You can set the display interval of time (in seconds or minutes) for slide shows to be
played automatically.
• [Display effect]
When playing a slide show, the projector can give various display effects or transitions
to each slide being displayed.
The transitions available are listed below:•None
Display each slide normally.•Wipe
Display the next slide gradually upward (Wipe  ↑), downward (Wipe  ↓), to the left
(Wipe  ←), or to the right (Wipe  →), over the current slide.•Dissolve
Display the next slide gradually in a certain fixed block pattern over the current slide.•Cover
Display the next slide as sliding upward (Cover  ↑), downward (Cover  ↓), to the left
(Cover  ←), or to the right (Cover  →), over the current slide.•Checker
Display the next slide gradually from the left using checkered blocks over the current
slide.•Zoom/Rotate zoom
Display the next slide by enlarging it gradually, either straight from the center (Zoom)
or while turning it starting from the center (Rotate zoom), over the current slide.•Belt wipe
Display the next slide gradually in stripes from both sides, over the current slide.•Blind
Display the next slide, as if it opened like a window blind, over the current slide.
• [Play icon]
The slideshow icon can be displayed.•Standard
The projector handles the slideshow icon as follows depending on the “ On/Off”
setting of  Icon on the projector’s menu.
Icon On :The projector displays the icon upon the start of playing a slide show and
turns it off after a few seconds.
Icon Off :The projector does not display the icon.•Continuous
The projector keeps the icon displayed during the slide show.
• [Thumbnail display]
Select the form of a thumbnail list.
All :Displays a thumbnail preview of JPEG files, and if any JPEG files exist in the
folder displays the leading thumbnail image.
File :Displays only a thumbnail image of JPEG files. The thumbnail image of the JPEG
files in the folder is not displayed.
Off :Displays a dummy icon without displaying thumbnail preview.
• [Unplug device]
Run when unplugging a USB memory, a USB memory card reader or a digital camera
and the like.
■ Setting slideshow options
Slideshow is the function to display the JPEG image files stored in a memory PC card
or a USB memory one after another at fixed time intervals. When switching from one
image to the next, Slideshow can add various display effects (transitions) to them. If you
select  Slide Show , the following items can be set.
Description
Item
A uto. demo
Interval
Display effect
Play icon
Thumbnail 
display
Unplug device
On           Off   (Select whether to automatically start a slide show 
when a PC card or a USB memory is plugged.)
Select the slide show display interval.
      or      : Begin a slide show. Use the           buttons to select.\
 
5 sec./10 sec./30 sec./1 min./3 min./5 min./10 min.
Select the slide show display effect.
      or      : Begin a slide show. Use the           buttons to select.\
None / Wipe    / Wipe    / Wipe     / Wipe     /  Dissolve / Cover    / \
Cover    / Cover     / Cover     /  Checker / Zoom / Rotate zoom / 
Belt wipe / Blind
Standard           Continuous
Switch the form of a thumbnail list.
All           File           Off
Run when unplugging a USB device.
Confirm : Yes           No
● Details on individual items•[Auto. demo]
On :A  slide show begins automatically when a memory PC card is inserted and input
s witches to Wireless/Card. At this time, the JPEG files in the root directory of the
memory PC card are used in the slide show. If the input has already been switched
to Wireless/Card, the slide show begins automatically when the memory PC card
is inserted.
The Auto Demo function is also available with a USB device.
•T o pause the slide show, press the 
 button. Pressing this button again allows
the slide show to begin. To stop the slide show, press the  RETURN button.
Off :A list of thumbnails will be displayed when connecting with a memory PC card, a
USB device or the like. Select a desired JPEG file from the list.
Note
• The Auto Demo function does not work when using a USB memory card reader to mount
m ultiple media. 
						

							63
Operations
62
●Playing a slide show from a thumbnail list1
Plug a memory PC card or a USB device.Plug a memory PC card or a USB device according to the procedure in “ Mounting a
PC card ” 
p.49
 or “Connecting USB memory” 
p.50
, respectively
.
The projector starts loading data from the memory PC card or the USB memory and
displays a thumbnail list on the screen.
2
Searching for a target file• Use the 
 
 
 
 buttons to move the orange frame over the desired file or folder.
• If there are multiple pages of thumbnails, click the 
 button on the bottom row to go to
the next page, and the 
 button on the top row to go to the previous page.
•T o open a folder, move the orange frame to the desired folder and press the 
 button.
Y ou can navigate down up to 5 levels using the same procedure. Pressing the
RETURN  button returns you to the next or other upper level folder.
3
Displaying slides• Pressing the 
 button with a file selected displays the image in that file only in full-
screen view on the screen as a slide. Pressing the 
 button enters the automatic play
mode.
•T o return to the thumbnail list display screen, press the  RETURN button.
4
Changing slidesPressing the 
 
 buttons with a slide displayed changes slides.
(
:  previous slide; 
: next slide. These buttons are not available during an automatic
play.)
Projecting images stored in a memory PC card or USB memory (Continued)\
■ Playing a slide show from a thumbnail list
With  Auto. demo  set to Off in “ Setting slideshow options ”, data readout begins when
a memory PC card or USB device is inserted and the input switches to Wireless/Card
or USB memory. A list of thumbnails will then appear on the screen.
The figure below is an example of this process:
Thumbnail image of 
first file in folder
Folder
Thumbnail 
image of file
File
Previous page exists
Current File Name
Current Folder Name
Operation Guide
Orange frame: currently 
selected file or folder
Thumbnail list numberCurrent list No./Total number of lists
Next page exists
Symbols in the thumbnail list
Indicates that there is no data to
be displayed in the folder.Indicates that an unsupported
JPEG or other file is present.
Indicates that only folders are
inside the folder.Indicates that the JPEG or other
file is not supported.When the  Thumbnail display  is
set to  Off, the screen appears
like this. 
						

							65
Operations
64
Checking the projector status■Status display
To check the current status of the projector, select  Status display in step 2 in
“ Projector settings ” 
p.53
. The following items of information will then be displayed.
Application The name of the application currently running on the projector is
displayed.
(Examples: Slideshow, Wireless Utility)
Device
When no device is plugged
“Type” is displayed.
When a memory PC card or USB memory is plugged“T ype
/Free space/Status” are displayed.
When a wireless LAN PC card is plugged
“
Type
/MAC address/Mode/Channel/SSID/Encryption/IP address/
Subnet mask/Gateway” are displayed.
Ve rs i o n The firmware version number of the wireless/card feature or the
USB memory feature is displayed.Note
•This product contains a piece of software (hereafter the Software) licensed to TOSHIBA
CORPORATION (hereafter TOSHIBA) by AXE, Inc. (hereafter AXE). The copyright and
other intellectual property rights of the software are held by AXE or the licensor.
The software is protected by the Copyright Law, Universal Copyright Convention, and
other intellectual property laws and agreements. The permission of AXE or the licensor
m ust therefore be obtained before the software can be reproduced.
Note, however, that the software is partly covered under the GNU General Public License
V ersion 2 (hereafter GPL2). You can obtain a copy of GPL2 at http://www.fsf.org/copyleft/
gpl.html. AXE will provide the GPL-covered source code of the software in accordance
with the terms of GPL2. Contact AXE if you need it.
An OS of axLinux is a registered trademark of AXE, Inc.
5
Rotating a slidePressing the 
 
 buttons with a slide displayed rotates the slide 90 degrees. The
rotation information is preserved as long as you remain in the current folder.
(
:  Rotate left; 
: Rotate right. These buttons are not available during an automatic
play.)
Notes
• The thumbnail display order and slide order goes in order from shortest file name to
longest. If two file names have the same number of characters, they are ordered
numerically if numbers are used in the file name, and alphabetically otherwise.
• It is possible to give presentations without using a computer by converting presentations
created with Microsoft
® Po werPoint
® into JPEG files using the  JPEG Conversion Tool,
and storing them on a memory PC card or a USB memory. 
p.75
Note, however, that functions such as animation effects and hyperlinks cannot be used,
so it should be tested before the actual presentation.
•F reeze function can not be used during slide show or automatic play.
•A  slide show is terminated when the input is switched to another.
• With some USB memories, the slideshow playback may stop in the midway. When
encountering such a phenomenon, use another USB memory because the current one is
not suppor ted.Projecting images stored in a memory PC card or USB memory (Continued)\
 
						

							67
Operations
66
Using the Wireless Utility■Displaying a computer’s screen via the projector1
Launch the Wireless Utility
software application.When the  Wireless Utility  launches, the Screen
Image  transmission mode window appears on
the computer screen.
To  switch to the  Screen Image  transmission
mode window from another mode, click on the
Screen Image  icon 
.
2
Select Transmission  mode.Click on Update automatically  or Update manually . See step 
6 for the meanings of
Update automatically  and Update manually .
3
Click on the Advanced button.The Screen Image: Advanced Settings  dialog
appears. Set the dialog as shown below, as
necessary.
• Interruption
Check the  No Interruptions  checkbox to prevent
other computers from interrupting the projector, for
e xample, during presentation in the  Update
automatically  mode.
• Window Display
Select the  Place in Tasktray at the start of
transmission  checkbox to iconify the  Wireless
Utility  and place it in the computer’s tasktray
when transmission initiated.
To  display the window, double click on this icon, or
r ight click and select  Open from the popup menu.
Even with the  Wireless Utility  window minimized,
y ou can use the pop-up menu to stop or resume
transmission as described in step 
4 and later.
• Mode
Selecting  High quality  improves the quality of the
projected image, but lowers communication
speed. Selecting  High speed has the opposite
effect.
Installing the applicationsIf you will use the wireless LAN PC card function, install the application o\
n the supplied
CD-ROM onto your computer.■ System Requirements
Supported OS: Windows
® 2000, Windows
® XP
CPU: P entium M 1 GHz or higher recommended
RAM: 256 MB or more recommended
Screen area (resolution): 1024 by 768 pixels recommended
■ Application Types and Major Functions
Wireless UtilityThis application is used for wireless connections. Use it to send the images from the
computer’s screen to your projector, and display on the screen.JPEG Conversion ToolUse to convert JPEG and other files into a format that can be displayed as a slide show
using a memory PC card or a USB memory.
■How to install
In the supplied CD-ROM, select the  Wireless Utility folder, and run  setup.exe. F ollow
the instructions on your computer screen.
During the installation, a dialog box may appear with the message “ Digital Signature
Not Found ” and the prompt “ Do you want to continue the installation? ”. Click on the
[ Y es (Y) ] button to continue the installation.
When installation is finished, the following shortcuts will appear on your computer’s
desktop:
Wireless Utility  →
Operations 
p.67
JPEG Conversion Tool  →
Operations 
p.75
■ How to uninstall
Select [ Start Menu ] →  [Settings ] →  [Control Panel ] →  [Add/Remove Programs ],
and remove  Toshiba Data Projector  from currently installed programs.Notes
•Your computer screen may temporarily go out during installation, but it is not an error.
• Before beginning installation or uninstallation, you need to log on as Administrator. 
						

							69
Operations
68
Using the Wireless Utility (Continued)
■
Displaying a JPEG image saved on a computer via the projector
1
Launch the Wireless Utility software application.The Screen Image  transmission mode window appears on the computer’s screen.
2
Click on the File icon 
.
The Wireless Utility
window changes to  File
transmission mode.
3
Click on the Browse button, and
select the file to send.Clicking on the  Browse button displays the  Open
dialog box. Select the file to send, then click on the
Open  button.
The selected file is added to the pull-down list in the
Wireless Utility ’s Transmission File  field.
4
Select the file to be sent from the
pull-down list of the Transmission
File field.Click on the Transmission File  field’s 
 b utton to
display the pull-down list. Select the file to be sent
from this list.
A thumbnail of the selected file appears in the
Preview  box. The file displayed here will be
transmitted.
Step 
3  can be skipped.
The way that drag and drop the file to be sent from the desktop or Windows Explorer
into the  Preview  box is also available. In this case as well, the selected file is added to
the file pull-down list  Transmission File  field’s.
4
Select the screen image you wish
the projector to display.Select Desktop
The computer screen image is transmitted as-is
.
Select application window
Select a running application (e.g. Microsoft
®
PowerPoint
®), and send that application’s
window only.
The desktop and a list of running applications are displayed.
Select the desired application from this list. (If the desired
application is not on the list, launch it. Note that if too many
applications are running, it will consume the computer’s
resources, which could slow communication speed.)
5
Select the projector to transmit to.The IDs of projectors accessible for communication
will be listed. (When a projector name is set, that
name appears instead of MAC address.) Select the
checkbox of the projector you wish to transmit to
from this list. Then icon 
 is displayed on the
projector’s screen for few seconds
.
It is possible to select up-to four projectors.
6
Click on the 
 button.
When “Update automatically” is selected in step 
2
Screen images are sent consecutively after the 
 button is clicked.
When “Update manually” is selected in step 
2
A single screen image is sent when the 
 button is clicked.
7
To  halt transmission from Update automatically, click on the
 button.
If the  Wireless Utility  icon has been placed in the tasktray, double click on the icon to
display the window, then halt transmission, or right click on the icon, and halt transmission
.
Notes
•It may not be possible to transmit the images from movie player or other video applications
.
• When using “ Update automatically ”, the transmitted image refresh rate depends on the
performance of the computer you are using and the surrounding radio wave environment.
• The projector screen may have a few differences from the computer screen.
•
It is not possible to transmit to a projector that is already receiving from another com\
puter
.
• If you selected application window in step   
4, if that application is not active (in use), the
image may not be correctly displayed by the projector.
• The projector ID is the MAC address of the wireless LAN PC card inserted into the
projector. 
						

							71
Operations
70
Using the Wireless Utility (Continued)5
Select the projector to transmit
to.The IDs of projectors accessible for
communication will be listed. (If projector name
has been set up already, it is shown instead of
the MAC address.) Select the checkbox of the
projector to be transmitted to from this list. Then
icon 
 is displayed on the projector’s screen
f or few seconds.
It is possible to select up-to four projectors.
6
Click on the 
 button.
The selected file’s image is displayed by the projector.Note
•Only one file can be sent at a time. To send another file, repeat steps 
4 and 
6.
■ Easy Connect utility
This feature allows users to easily connect the projector to a computer over wireless
networks, without making  Network settings via Wireless Utility .
Launch the  Wireless Utility  software application and click the Tool button 
 to bring
up the  Wireless LAN Setting Utility  dialog box. Select a desired connection mode in
this dialog box.
● How to set up a simple 1:1 connection•Setting on the projector1
Turn the projector power on.
2
Insert the supplied wireless LAN PC card to the PC card slot.
3
Switch the input to Wireless/Card.
4
Press the 
 button on the projector control panel.
• Setting on the computer1
Launch the Wireless Utility software
application.When the  Wireless Utility  launches, the
Screen Image  transmission mode window
appears on the computer screen.
2
Click the Tool button 
.
The  Wireless LAN Setting Utility  dialog box
appears.
3
Select Simple 1:1 connection then
click OK.The connection starts up.
When a connection confirmation message
appears, proceed as instructed in the
message.
4
The projector name of the connected
projector or the MAC address of the
wireless LAN PC card is displayed. Notes
• This operation is allowed only when the Transmission mode is set to  Ad hoc in the
projector network settings.
• The operation procedure of the projector setting and the computer setting can be\
altered without affecting the connection setup, assuming the operation on each side
is complete within 60 seconds.
● How to connect USB memory
Set up wireless LAN using a commercial USB memory. See 
p.59
 for available USB
memories.
Copying the computer settings to the projector• Setting on the computer1
Plug the USB memory into the
computer.
2
Click the Tool button 
 of the
Wireless Utility to bring up the
Wireless LAN Setting Utility dialog
box. Select USB memory connection
and click OK.
The dialog box for USB memory connection appears.
3
Select the setting information then click OK.The setting information is saved to the USB memory. 
						

							73
Operations
72
4
Unplug the USB memory from the computer.To unplug the USB memory, follow the instructions in the user’s manual supplied
with the USB memory or the computer.
• Setting on the projector
1
Turn the projector power on.
2
Insert the supplied wireless LAN PC card to the PC card slot.
3
Switch the input to Wireless/Card.
4
Plug the USB memory into the projector.A message appears, notifying that the projector settings have been changed.
5
When the setting is complete, the connection is established. The
projector name of the connected projector or the MAC address of the
wireless LAN PC card is displayed.
Modifying the computer settings using the projector settings
• Setting on the projector1
Turn the projector power on.
2
Insert the supplied wireless LAN PC card to the PC card slot.
3
Switch the input to Wireless/Card.
4
Plug the USB memory into the projector.A message appears, notifying that the projector settings have been changed.
5
Select Easy Connect (USB) in Wireless Utility settings from the
Wireless/Card menu and press the 
 b utton.
6
When a confirmation window appears, click Yes then press the b utton.The network settings are saved to the USB memory. When successfully saved, a
message appears.
7
Unplug the USB memory following the instruction in 
p.50
.
• Setting on the computer1
Launch the Wireless Utility software
application.
2
Plug the USB memory into the computer.
3
After a confirmation message appears,
make settings.
4
When the setting is complete, the connection is established. The
projector name of the connected projector or the MAC address of the
wireless LAN PC card is displayed.
This operation is allowed only when the Transmission mode is set to  Ad hoc in the
projector network settings.
● Profile settings
This feature allows the user to save the computer settings.
This feature is useful when you need to change wireless LAN settings according to
where you use the computer.
     
●WEB browser
Where the computer and the projector are connected over wireless LAN, bring up the
window of Projector Configuration Tool by pressing the  WEB browser button.
 Precautions
• If the page is not displayed correctly, re-select the projector.
• When the network settings are changed, the network connection is disconnected. If
you wish to reconnect, set up the computer again.
Precaution
•The simple 1:1 connection, the USB memor y connection and the profile setting may not
work normally depending on the type of the wireless LAN PC card and the wireless\
 LAN
embedded computer. When such a case arises, use the Wireless Utility menu to make
network settings manually
.
■ Operating the projector
This function can be used with any projector input.
Note, however, that this will not function with a memory PC card.
1
Launch the Wireless Utility software application.The  Screen Image  transmission mode window appears on the computer’s screen.
Using the Wireless Utility (Continued) 
						

							75
Operations
74
How to use the JPEG Conversion ToolThe JPEG Conversion Tool  converts JPEG files not suppor ted by the projector, image files
in other formats, Microsoft
® PowerPoint
® files, and the like into JPEG files suppor ted by the
projector. The JPEG files converted with this tool can be displayed by sending them using the
wireless LAN PC card 
p.69
, or saving them on a memor y PC card or a USB memory.
■ Launching the JPEG Conversion Tool
The window shown in the figure to the right appears on the
computer screen.
Drag the  Image Quality Settings  slider to the left or right to set the
image quality of the file after conversion. Lower values create
smaller files, but lower the image quality. (It is not possible to restore
the quality of an image after it has been lowered.)
■ Converting an image file
This converts JPEG files using compression formats not supported by the projector,
Windows
® metafiles (wmf), and bitmapped files (bmp) into JPEG
files.
(1) In the  Conversion Method  field, select Converting image
file . (Status on launch)
(2) In the  File settings  field, click on the  Browse button for
Original Image File Name .
The  Open  dialog box appears.
(3) In the  Open dialog box:
(a) Specify the location of the file to be converted; and
(b) In the  Files of Type  field, click on the 
 b utton to select
the file format. A list of files of that format appear in the
Open  dialog box.
(4) In the  Open dialog box, select the file to convert, then
click on the  Open button.
(5) In the  JPEG Conversion Tool  window, in the File
settings  field, select  Browse for  File name after
conversion . The  Save As  dialog box appears.
(6) In the  Save As dialog box:
(a) Specify the location in which to save the converted
file;
(b) Enter a file name of up to 8 characters in the  File
Name  field; and
(c) Press the  Save button.
(7) (a) In the  JPEG Conversion Tool , click on the
Conversion  button.
(b) A confirmation dialog box opens. Click  Ye s.
The computer converts the file. When it finishes a
message  appears informing you that a  “JPEG file has
been created” .
(1)
(2)
(5)
(7)-(a) (1)
(2)
(5)
(7)-(a)
(3)-(b) (3)-(b)
(3)-(a)
(4)(6)-(b) (6)-(c)
(6)-(a)
(7)-(b)
(7)-(b)
2
Click on the Remote
Control button.The 
Remote Control  window
appears.
As the  Wireless Utility  window is
still displayed, you can operate the
projector via the  Remote Control
window, while using the Wireless
Utility’s functions.
While it is possible to use this function merely to operate the projector, closing the
Wireless Utility  also closes the Remote Control  window.
3
Select the projector to be operated.In the Remote Control  window, click on the 
 button, and select the
desired projector from the pull-down list. When you make a selection,
the Remote Control window displays as shown in the right figure.
Only one projector can be selected. (It is not possible to operate
m ultiple projectors.)
4
Click on the Remote Control window’s buttons.The function of each button and box is as follows:
Po wer On :Turns projector power on.
Po wer Off :Turns projector power off.
Freeze :The picture is paused.
Input  (box) : Click on the 
 button, and select the desired input from the pull-down
list.
Go : Switches to the input selected in the Input box.
Mute : Cuts off picture and sound. Click again to restore picture and sound.
V olume +/– :Adjust sound volume.
Resize Off :Restores the picture to its original size.
Resize +/– :Adjusts the enlargement ratio.
 :M ove screen (up/down/left/right/diagonal)
5
To  quit, click on the 
 button on the Remote Control
window.
P erforming this does not close the  Wireless Utility window.
To  e xit both the  Wireless Utility  and the Remote Control , click on the 
 b utton on
the  Wireless Utility  window.
Using the Wireless Utility (Continued) 
						

							7677
Operations
■Making a presentation with converted JPEG files
(1) Copy the folder created by the  JPEG Conversion Tool, or its contents, onto a
memory PC card or a USB memory.
(2) Use the step 
1 in “ Playing a slide show from a thumbnail list ” 
p.63
 to display a
list of thumbnails.
(3) Follow the instructions in step 
2 in “ Playing a slide show from a thumbnail list ”
p.63
 to find the thumbnail of the first slide, Slide001.jpg, and move the orange
frame to it. (Select Slide001.jpg)
(4) Press the 
 button on the remote control. An enlarged view of the first slide
appears on the screen. This starts the presentation.
(5) To continue to the next slide, click on the remote control’s 
 button. To go back to
the previous slide, click on the 
 button.
■ Creating a screen capture and converting it into a JPEG file
This function saves the current computer screen as a JPEG file.
(1) In the  Conversion Method  field, select Creating screen
capture .
(2) In the  File settings  field, click on the  Browse button for  File
name after conversion .
The  Save As  dialog box appears.
(3) In the  Save As dialog box:
(a) Specify the location in which to save the converted file;
(b) Enter a file name of up to 8 characters in the  File Name
field; and
(c) Click on the  Save button.
(4) (a) In the  JPEG Conversion Tool  window, click on the
Conversion  button.
(b) A confirmation message appears. Click  Ye s.
The computer creates a screen capture, and
converts it into a JPEG file in the specified location.
When it is finished, a message appears to tell you
that a  “JPEG file has been created” .Note
•The maximum resolution of JPEG files created with the  JPEG Conversion Tool is 1,024 ×
768 pixels.
(1) (1)
(2)
(2)
(4)-(a)
(4)-(a)
(3)-(b) (3)-(c)
(3)-(a)
(4)-(b)
(4)-(b)
How to use the JPEG Conversion Tool (Continued)■
Converting files created with Microsoft
® PowerPoint
®
This process provides presentations without using a computer by converting
presentation files created with Microsoft
® PowerPoint
® into JPEG files, storing them on
a memory PC card, and displaying them in a slide show.
•T o use this conversion mode, Microsoft
® PowerPoint
® must be installed on the
computer.
• Only static images are supported by this process. Animation and audio are not
supported.
Presentation files created with Microsoft
® PowerPoint
® usually
consist of several slides. For this reason, the tool creates a folder
with the name specified in step (5), below, and file for each slide
is created in the folder (starting with slide001.jpg).
(1) In the  Conversion Method  field, select Converting PPT file .
(2) In the  File settings  field, click on the  Browse button for  PPT
File Name .
The  Open  dialog box appears.
(3) In the  Open dialog box:
(a) Specify the location of the file to be converted; and
(b) Select the PowerPoint
® presentation file to convert,
then click on the  Open button.
(4) In the  JPEG Conversion Tool  window, in the File
settings  field, click on the  Create button for  New
folder name .
The  Folder create  dialog box appears.
(5) In the  Folder create  dialog box, in the  Folder name of
document  field, specify a folder name of 12 characters or less.
(6) In the  Folder create  dialog box, click on the  Selection button.
The  Browse Folders  dialog box appears.
(7) In the  Browse Folders  dialog box:
(a) Specify the location in which to save the folder; and
(b) Click on the  OK button.
(8) In the  Folder create  dialog box:
(a) Click on the  Create button.
A confirmation dialog box appears;
(b) Click on the  OK button.
(9) (a) In the  JPEG Conversion Tool  window, click on the
Conversion  button.
(b) A confirmation dialog box opens. Click  Ye s.
The computer begins to convert the file. When it finishes,
a message appears informing you that a  “JPEG file has
been created” .
(1)
(2)
(4)
(9)-(a) (1)
(2)(4)
(9)-(a)(3)-(b)
(3)-(a)
(6)
(8)-(a) (6)
(8)-(a) (5) (5)
(7)-(a)
(7)-(b)
(7)-(b)
(8)-(b)
(8)-(b)
(9)-(b)
(9)-(b) 
						

							79
Operations
78
4
Select items from the menu on the left.Wireless/Card Settings
:Make settings for the Wireless/Card input menu.
USB Memory Settings: Make settings for the USB memory input menu.
Status Display: Verify the projector state.
Features: Shows the functions available with the Wireless/Card and
USB input menus.
T op: Returns you to the top page.
TOSHIBA Projector Site
: The browser will display the home page at http://
multimedia.projector-toshiba.com/map.html, providing
projector information. The home page address is subject to
change without notice.
(The Toshiba’s web site can be browsed only when your
computer can access the Internet.)
● Details on major items•Wireless/Card SettingsWhen  Browser authentication  has been set to On, access to the setup page requires the input
of the password.Wireless Utility
: The items displayed on the screen can be set. Entering individual items
and press the  Execute button to update their setting. Note, however, that
security items such as “ Remote control” and “ Browser authentication ”
cannot be set.
Slide Show: The items displayed on the screen can be set. Entering individual items
and press the  Execute button to update their setting.
• USB Memory Settings
When  Browser authentication  has been set to On, access to the setup page requires the input
of the password.Slide Show: The items displayed on the screen can be set. Entering individual items
and press the  Execute button to update their setting.
• Status display
Displays some states of the projector.
Projector: Displays the contents of status display in the menu.
Wireless/Card: Displays the contents of status display of the Wireless/Card input.
USB Memory: Displays the contents of status display of the USB memory input.
Maintenance: Describes an error if it occurs, for example, when the lamp has blown.Note
•Clicking the ? button opens a popup help window.
Setting up the projector using a Web browser■ How to use the “Projector Configuration Tool”
The “ Projector Configuration Tool ” uses the Web server features of the projector to
set up the projector using a wireless LAN PC card.
When using the “ Projector Configuration Tool ”, set up the wireless LAN connecting
the projector and the computer.
1
See “Checking the projector status” 
p.65
 to display
information on the screen and write down the IP address.
2
Invoke Internet Explorer.Internet Explorer Ver. 6.0* is recommended. Enable the Javascript functions.
* Toshiba does not guarantee the operation for later versions.
3
In the address bar, enter the IP address
“http://xxx.xxx.xxx.xxx/” recorded in step 
1
 above.
The Web browser will then display the following page.
Projector name
Projector ID
MenuNote 1: To prevent access from third parties, the projector is restricted to permit access
only from the computer that has been set up for the TCP/IP to have the same
network address as the projector.
Note 2: If you use a proxy server, do not enable the proxy when accessing the above IP address.
When the wireless LAN is set to use Ad hoc mode, use the  WEB browser function
in the Easy Connect menu of Wireless Utility.
Note
•This function can be enabled using the  WEB Browser function in the Easy Connect menu
of Wireless Utility without specifying the URL into the browser’s address bar.