Toshiba Tdp Tw350uk Projector User Manual

							21
Preparations
20
Operating a computer using the remote controlA computer can be operated using the projector’s remote control.  This function is available
on any computer with the Windows 98/98SE, Windows Me, Windows 2000, or Windows XP
OS, that is equipped with a USB port which can support USB1.1 (The mouse remote
control receiver is also supported on OS 9 or OS X for the Macintosh).  However, please
note that Toshiba does not guarantee the operation of all computers.1
Connecting a computerConnect the mouse remote control receiver (supplied) to a computer.Mouse remote control receiverTo USB port2
Operating a computerOperate remote control’s buttons towards the mouse remote control receiver.
●Moving the mouse pointer
Press the mouse control button in the direction you wish the mouse pointer to move,
then press.
●To left click
Press the L-CLICK button.
●To right click
Press the R-CLICK button.
●To drag and drop
Holding down the L-CLICK button, move the mouse control button until the mouse
pointer is over the desired location, then release the L-CLICK button.
●Using the computer’s page up [
↑] and down [
↓] function
Press the PAGE+ and PAGE- buttons to switch PowerPoint
® slides.
The remote control may fail to operate
if the mouse remote control receiver is
exposed to bright sunlight or
fluorescent lighting.
In such a case, change position or
direction of the mouse remote control
receiver and retry.
Mouse control
Remote Control Front Remote Control Rear
PAGE –
PAGE +
R-CLICKL-CLICK
&4:
4&561

■Operating the remote
controlTurn on the ON/OFF switch of the
remote control.
Point toward the projector’s
infrared remote sensor, and press a
button on the remote control.•Operating the projector from the front
Approx. 15°Approx. 5m
•Operating the projector from the rear
Approx. 15°
Approx. 5m
■Loading dry-cell batteries
into the remote controlqRemove the battery cover.wInsert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.Two batteries (LR03, SIZE AAA) are
used.
eReplace the battery cover. Dry-cell batteries•Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
•Remove batteries from remote control when not using for extended periods.
•If the remote control stops working, or if its range decreases, replace all the batteries with
new ones. The remote control•Turn off the ON/OFF switch of the remote control when not in use or to store in baggage.
•The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
•Do not drop or bang.
•Do not leave in hot or humid locations.
•Do not get wet or place on top of wet objects.
•Do not take apart.
•In rare cases, ambient conditions could impede the operation of the remote control. If this
happens, point the remote control at the main unit again, and repeat the operation.Preparing and using the remote control 
						

							23
Preparations
22
Placement StylesAs shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
Default setting menu 
p.44
, in accordance with your needs.
Placement
 WARNING
•Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
•If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
•If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.Floor-mounted front projection Floor-mounted rear projection Ceiling-mounted front projection Ceiling-mounted rear projection 
Projection Distance and SizeUse the figures, tables, and formulas below to determine the projection size and projection distance.
(Projection sizes are approximate values for full-size picture with no keystone adjustment.)Screen
As seen from above
As seen from the side
90°
a
90°
H
Lens center
a (min length) = projection size (inches) – 1.552
32.929
a (max length) = projection size (inches) – 1.0087
21.735
projectionprojection distance a (m)
height (H)
min length max lengthsize (inches)
(zooming max) (zooming min)(cm)
33 – 1.17 6.840 1.17 1.79 8.260 1.77 2.71 12.380 2.38 3.63 16.5100 2.99 4.55 20.6150 4.51 6.85 30.9200 6.03 9.16 41.1250 7.54 11.46 51.4
300 9.06 13.76 61.7
a is the distance (m) between the lens and the screen, and corresponds to a range of 1.17 m to 13.76
m. H is the height from the image bottom to the center of the lens. 
						

							25
Preparations
24
Notes
•When an AUDIO OUT terminal is connected, sound is not output from the projector
speaker.
•Output volume of AUDIO OUT terminal can be adjusted by the VOL button. Connecting with AV equipment
DVD video recorder, etc.DVD video recorder,
DVD player, etc.Audio amplifier, etc.
DVD video recorder, etc. Video recorder,
DVD player, etc.Video recorder, etc.
To DVI output
Conversion
adapter BNC-pin
(not supplied)
To  Y/C
B/CR output
Green (Y)/Blue
(C
B)/Red (C
R)
DVI cable-29 pin
(not supplied)Audio cable
(not supplied)To audio output
White (L)/Red (R)
Audio cable
(not supplied)
Monitor cable Mini
D-sub 15P-BNC
(not supplied)To audio output
White (L)/Red (R)
Audio cable
(not supplied)To audio
input
White (L)/
Red (R)
Audio cable
(not supplied)
To audio output
White (L)/Red (R)
To audio output
White (L)/Red (R)
To audio output
White (L)/Red (R)
Conversion adapter
BNC-pin (not supplied)
Green (Y)/Blue (C
B)/
Red (C
R)Component cable
(not supplied)
To  Y/C
B/CR output
Green (Y)/Blue
(C
B)/Red (C
R)
AV  cable
(not supplied) Video cable
(not supplied) S-video cable
(not supplied)
To S-video
outputTo video output
•The MONITOR OUT terminal outputs analog RGB signals or component video signals (Y/
PB/PR) from the COMPUTER 1 IN, COMPUTER 2 IN, or from the COMPUTER 3 IN
terminal as selected with the INPUT button. If no input is selected, the MONITOR OUT
terminal outputs the input signals last selected among the COMPUTER 1 IN, COMPUTER
2 IN, and the COMPUTER 3 IN terminals. (Digital RGB signals are not output.)
•A computer monitor usually cannot accept Y/P
B/PR signals correctly.
Before connection•Read the owner’s manual of the device you are connecting to the projector.
•Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal 
p.88
, etc.
•Turn off the power of both devices before connecting.
•The figures are sample connections.
Connecting with computers
Notes
•Signals are output from MONITOR OUT terminal even in standby mode.
   From AUDIO OUT terminal, no audio signal is output.
•Moving pictures played back on computers using DVD software may appear unnatural if it
is projected with this projector, but it is not a malfunction.Connection
p.91
Computer (for control)
ComputerMonitor
Speaker with
built-in amplifier
To RS-232C
terminalTo DVI output
DVI cable
(not supplied)Audio cable
(not supplied) To audio outputTo audio
input
Audio cable
(not
supplied)
Control cable
RGB cable
(supplied)Audio cable
(not supplied)
To audio
output
To RGB output
ComputerMonitor cable Mini
D-sub 15P-BNC
(not supplied)
To RGB outputTo audio
output Audio cable (not supplied)
Computer 
						

							27
Operations
26
■Connecting the power cord1
Insert the power cord connector into
the AC IN socket of the projector.
2
Insert the power cord plug into a
wall or other power outlet.
■ Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
•The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed 
p.28
.
•Y ou can disable the beep sound in the  Display setting menu 
p.41
.
• When [ Key lock] is [On], the operation buttons of the projector do not work 
p.44
.
• When [ Password ] is [On], the start-up screen is displayed after the Password entry
screen disappears 
p.44
.
■ Turning the power off1
Press the ON/STANDBY button.A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.A beep sound is made (if the beep sound is set to [ On]) and the screen turns off, but
the internal cooling fan continues to operate for a short while. Then, the projector goes
into standby mode.
When cooling lamp During internal cooling After cooling complete
A
B
C
A
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on.
If you are in a hurry, there is no problem with unplugging the power cord or
turning off the main power switch in this state.
B
After the LAMP indicator goes off, the FAN indicator keeps lighted and the
cooling fan continues to operate for a short while, in order to expel excess
internal heat.
C
In standby mode
Note
• The projector consumes about 16W of power in standby. We recommend that you unplug
the power cord or turn off the main power switch if you will not be using the projector for
an extended period. (When [ Wireless standby] is [On], it consumes about 23W during
standby.)
Precaution
• If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.
Turning the power on and offOperations
■ Turning the power on1
Turn on the main power
switch.The ON/STANDBY indicator will
change to orange, indicating standby
mode.
2
Press the ON/STANDBY
butt on.The power turns on with a beep sound
(if the beep sound is set to [ On]), and
the following 3 green indicators light:
ON/STANDBY, LAMP, and FAN. After a
moment, the start-up screen appears.  CAUTION
•
Do not look into the lens while the lamp is on.  The strong light from the lamp may cause
damage to your eyes or sight.
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
• Do not place your hands, face, or other objects near the air exhaust. Doing so could cause
bu rns, deform/break the object.
Po wer cord connector
(Supplied)
Start-up screen
Control panel Remote
Control
Notes
• The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the  Display setting  menu 
p.41
. 
						

							29
Operations
28
5
Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjuste\
d by the foot
adjuster.qLift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
w To fine adjust the angle, twist the
f oot adjuster.
e To adjust the horizontal angle, use
the tilt adjuster.
To  stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector.
6
Adjusting the screen size and focusq
Use the ZOOM button to adjust the screen size.
w
Use the FOCUS button to adjust the screen focus.
7
Adjusting the volume with the 
 
 buttons
The speaker volume can be adjusted when an audio signal is being input.Notes
• While a text entry screen (e.g., the Password entry screen) is displayed, the remote
control’s  FOCUS and ZOOM  buttons function as numeric keys, and therefore cannot be
used to adjust the screen size or focus. In such a case, use the  FOCUS and ZOOM
b uttons on the projector to make adjustment or retry after quitting the text entry screen.
• Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.
•A  lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out.  This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
• The DMD
TM is made using extremely advanced technology, but there may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.  Please
note that these are not malfunctions.
• Although this projector supports a wide range of RGB signals 
p.88
, any resolutions not
supported by this projector (XGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
e xternal output should be set to XGA resolution.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
• If no signal is being input from the connected equipment or signal input\
 is stopped while
projecting, the “No signal” will appear.
• If a signal not supported by the projector is input, the “Unsupport signal” will appear.
• If an unavailable operation button is pressed, the 
 icon will appear.



1
2
3
1
Turn on the power.Tu rn on the power by following the instructions in “ Turning the power on ” 
p.26
.
The Easy setup function works to automatically adjust the screen focus and correct the
keystone distortion. If RGB signals are input, auto-setting is also made. This operation
does not take place when [ Easy setup] in the Default setting  menu is [Off] 
p.44
.
2
 Select the language and the lamp power (When using the
first time).When the projector is used for the first time after purchase, the start menu for lan-
guage (to display the menus and messages on the screen) and lamp power selection
and configuration is displayed in English. (If the screen is out of focus, adjust it
according to the step 
6.)
q Use the 
 or 
 button to select the
desired language and press the 
 button.
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step  w.
w Use the 
 or 
 button to select the lamp
power and press the 
 button.
The lamp power, if selected, will be toggled without
pressing the 
 button. The display automatically
disappears in a few seconds.
Notes• When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [ Reset all] is executed from the  Default setting menu 
p.44
, the
start menu will be displayed the next time when the power is turned on.
• The language can also be set via the  Display setting menu 
p.41
 and Lamp power
via the  Default setting  menu 
p.44
.
• This owner’s manual assumes that English has been selected.
3
Activate the connected device.Tu rn on and start the connected device such as a computer.
4
Press the INPUT button.An image of the connected equipment is projected.
Each time you press the  INPUT button, it switches to the input of the connected
equipment that is outputting video signals.Notes
• When [ Auto input search ] is set to [On] in the  Default setting  menu 
p.44
 (factory
setting is [ On]), the input is switched to the connected equipment that is outputting video
signals each time you press the  INPUT button 
p.45
.
• If no signal is being output from the connected equipment, pressing the \
 INPUT button
does not change the input and “There is no other input signal.” will appear.
Basic operations
English
F rench
German
Italian
Spanish
Po rtuguese
Russian
Swedish
Tu rkish
P olish
J apanese
Chinese (simplified)
Chinese (traditional)
K orean
Control panel Remote
Control 
						

							31
Operations
30
■Correcting the keystone distortion
When the projector placement angle against the screen is changed while p\
rojecting the
image, the picture will undergo keystone (trapezoidal) distortion.This projector is capable of correcting this keystone
distortion
.
1
Press the KEYSTONE button.The  Keystone  menu appears. By default, [ Auto keystone ] is selected.
Item Description
Automatically corrects vertical and horizontal keystone distortion.
Press      .
Screen shrinking at bottom             Screen shrinking at top
Screen shrinking on the left             Screen shrinking on the right
A uto  keystone
V -keystone
H-keystone
Adjusting vertical distortion [Auto]2
Press the 
 button.
The vertical and horizontal keystone distortion is automatically corrected. During
processing, the icon 
 will appear. When the processing is finished, the  Key-
stone  menu appears again. If you wish to make fine adjustment, use the 
 button
to select [ V-keystone ], and adjust with the 
 
 buttons.
Adjusting vertical distortion [Manual]1
Press the KEYSTONE button.
2
Select [V-keystone] by the 
 b utton.
3
Use the 
 
 buttons for keystone adjustment.
Adjusting horizontal distortion [Manual]
1
Press the KEYSTONE button.
2
Select [H-keystone] by the 
 button.
3
Use the 
 
 buttons for keystone
adjustment.
When the adjustment is finished, the menu
automatically disappears. The menu also disap-
pears when the  KEYSTONE or RETURN  button is
pressed.
Before correction
After correction
■ Easy setup
This function automatically adjusts the screen focus and corrects the keystone distor-
tion (Auto focus and Auto keystone functions).
Press the EASY SETUP button on the
projector or on the remote control.The icon 
 will appear during processing.
• Before pressing the  EASY SETUP button, be
sure to set Auto focus and select the items to
be adjusted by Auto adjustment 
p.44
.
• With [ Easy setup ] in the Default setting
menu set to [ On], the screen focus is
automatically adjusted and the keystone
distortion (vertical and horizontal) is corrected when the power is turned on.
(Automatic keystone distortion correction and auto-setting are selected by factory
setting.)
Notes•A  message appears on the screen if the auto-adjustment fails.
•A uto focus and Auto keystone functions are effective for projecting size from 40” to
100” diagonal (projection distance: 1.17 m to 3 m) at maximum zoom and 40” to 66”
diagonal (projection distance: 1.79 m to 3 m) at minimum zoom.Precautions• Depending on the room temperature and brightness as well as the projecting
surface condition and material, the adjustment may not be properly made. When
such a case arises, adjust the screen focus manually.
• Improper adjustment or correction may also occur if the AF sensor is obstructed or
the window gets dirty. Remove the obstruction and clean the AF sensor window in
such a case.
■ Using auto setting 
(Only for analog input from computer)
This function sets up the projector to the optimum state such as
sampling phase, frequency, screen position, and clamp for each
type of the input signal by using simple operations.
Press the remote control’s AUTO SET button.For computer input, the 
 icon will appear during processing.
Y ou can set as well by selecting [ Auto setting ] in the Image
adjustment  menu 
p.39
.
Notes•The image may not be projected or auto adjustment/setting may not be performed
correctly for input signals other than those supported by the projector 
p.88
, p.89
.
• If auto setting fails adjustment, adjust manually with the  Image adjustment menu
p.39
.
Using handy features
Control panel Remote
Control
Before correction
After correction
&4:
4&561Remote Control
&4:
4&561
Control panel Remote
Control
&4:
4&561 
						

							33
Operations
32
■
Cutting off the picture and sound temporarily (Mute)When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Press the remote control’s MUTE button.The picture and sound are cut off. (The Mute function is released
when pressing the MUTE button again.)Notes•The 
 icon will appear while mute is in effect.
•Operating any other functions will also cancel the muting.
■Changing picture mode
The projected image mode can be selected.
Press the remote control’s PICTURE button.Pressing the button switches Bright/Standard/True color in turn.Note•[Picture mode] of the Image adjustment menu has the same
function 
p.39
.
■Changing screen size
The screen size for the projected image can be changed.
Press the remote control’s SCREEN SIZE button.Pressing the button switches Full/Thru/Wide in turn.Notes•Thru display is available for computer-input images.
•[Screen size] of the Display setting menu has the same function 
p.41
.
•If you use this function on commercial video software, broadcast
or cable-broadcasting except for the purpose of your private viewing
and listening, it may infringe the copyright protected by the copyright laws.
■Freezing the image (Freeze)
The image being projected can be frozen. This function is to be used
to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.The picture pauses. (The Freeze function is released when
pressing the FREEZE button again.)Notes•The 
 icon will appear while freeze is in effect.
•Other operation will also release the freeze.
•Even if an image is frozen on the projector, the pictures are running on the video or
other equipment.
•If you use this function on commercial video software, broadcast or cable-
broadcasting except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.
Remote
ControlRemote
ControlRemote
Control
Notes•A message appears on the screen if the automatic keystone distortion correction fails.•Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.Precautions•Depending on the room temperature and brightness, the placement as well as the
projecting surface condition and material, the correction may not be properly made.
When such a case arises, make correction manually.•To manually adjust both vertical and horizontal keystones, adjust the vertical
keystone first then the horizontal.
■Resizing image
The projected image can be resized (zoomed in/out).1
Press the remote control’s RESIZE 
 button.
Each time you press the RESIZE 
 button, zoom ratio is up. You can keep
pressing.
2
To zoom out, press the remote control’s RESIZE 
 button.
Each time you press the RESIZE 
 button, zoom ratio is
down. You can keep pressing.
(However, the image cannot be smaller than the original
size.)
3
To move the area to zoom in, use the 
 
 
 
buttons.You can keep pressing.
4
To reset the zoom, press the RETURN button.The image is reset to the original size.Notes•The 
 icon appears while resizing.
•Operating a function other than Mute will release resizing.
•
As zooming is processed digitally, the image quality is degraded in larger zoom ratio.•During resizing or moving the zooming area, the image may be distorted.
Remote
Control
Remote
Control
Using handy features (Continued) 
						

							35
Operations
34
■Displaying two screens (SPLIT function)
This function displays two screens at a time.
Press the remote control’s SPLIT button.The projected image moves to the left (main
screen), and a new image is displayed to
the right (sub screen). To switch the sub and
main screens, press the remote controls
SWAP button.
To hide the sub screen, press the SPLIT
button again.Notes•Sound of the main screen is output.
•Size of the screens and input source of the sub screen can be changed in the
SPLIT menu.
•Compared with the main screen, the sub screen may suffer some slight image
degradation.
•Operating a function other than Mute, Freeze and volume control will release the
SPLIT mode.
•If you use this function on commercial video software, broadcast or cable-
broadcasting except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.
■SPLIT function setting
Pressing the MENU button while two screens are displayed displays the SPLIT menu.
This menu sets up both screens.
To hide the menu, press the RETURN button.
Sets size of both screens.
Selects the input source for the sub screen.
When the main screen is input from computer or Y/P
B/PR:
Press      or      , toggle the input with            and fix selection 
with      .
Video/S-video
When the main screen is input from video or S-video:
Press      or      , toggle the input with            and fix selection 
with      .
Computer 1 (Digital) / Y/P
B/PR 1 (Digital) / Computer 1 
(Analog) / Y/P
B/PR 1 (Analog) / Computer 2 / Y/P
B/PR 2 / 
Computer 3 / Y/P
B/PR 3 / Wireless/Card / USB memory
Size
Sub inputItem DescriptionNote•To enlarge the screen fully, select [Full] for [Size].
Remote
Control
Using handy features (Continued)■Display a sub screen (PIP function)
Another image can be added in smaller size
(referred as sub screen in this manual) to the
projected image (referred as main screen).
Press the remote control’s PIP
button.A sub screen is displayed in the currently
projected image (main screen).
To swap the main and sub screens, press
the remote control’s SWAP button.
To hide the sub screen, press the PIP button again.Notes•Sound of the main screen is output.
•Input select, display position and size of the sub screen can be changed in the PIP
menu.
•Operating a function other than Mute, Freeze and volume control will release PIP
mode.
•If you use this function on commercial video software, broadcast or cable-
broadcasting except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.
■Sub screen setting
Pressing the MENU button while the sub screen is displayed displays the PIP menu.
This menu sets up the sub screen.
To hide the menu, press the RETURN button.
Sets the sub screen size.
Large            Medium            Small
Sets display position of the sub screen.
Selects the input source for the sub screen.
When the main screen is input from computer or Y/P
B/PR:
Press      or      , toggle the input with            and fix selection 
with      .
Video/S-video
When the main screen is input from video or S-video:
Press      or      , toggle the input with            and fix selection 
with      .
Computer 1 (Digital) / Y/P
B/PR 1 (Digital) / Computer 1 
(Analog) / Y/P
B/PR 1 (Analog) / Computer 2 / Y/P
B/PR 2 / 
Computer 3 / Y/P
B/PR 3 / Wireless/Card / USB memory
PIP size
PIP position
PIP inputItem Description
Remote
Control 
						

							37
Operations
36
How to set password (from [Off] to [On])
1
Select [Password] in the Default setting menu and press the 
 or 
button.The password setting confirmation screen is displayed. ([OK] or [Cancel])
2
Select [OK] and press the 
 button.
The password entry screen is displayed.
3
Enter a four-digit number for the password using numeric keys of the
remote control.The input number appears as [****].
4
Re-enter the same password for confirmation.When the password is confirmed, the setting is complete and the password
becomes [On].
If the password is wrong, repeat the procedure from step 
2.
How to operate when password is [On]
1
Turn on the power.
2
The lamp lights and the password entry screen appears.
3
Enter the password using numeric keys of the remote control.If the entered password is correct, the start-up screen appears and the projector
goes into normal operation. If the password is wrong, a message appears to
prompt you to re-enter the password. If you enter a wrong password for more than
5 times, the projector will automatically power off and enter standby mode.How to cancel password (from [On] to [Off])
1
Select [Password] in the Default setting menu and press the 
 or 
button.The password entry screen is displayed.
2
Enter the password using numeric keys of the remote control.
3
The password cancel confirmation screen is displayed. ([OK] or
[Cancel])
4
Select [OK] and press the 
 button.
The [Password] is canceled and becomes [Off].Note•The password entry screen appears when the power is turned back on only after
the main power switch is turned off or the power cord is unplugged.If you forgot the password, please inquire your dealer. ■Screen combination of PIP and SPLIT functions
Computer 1 (Digital) / Y/P
B/PR 1 (Digital)
Computer 1 (Analog) / Y/P
B/PR 1 (Analog)
Computer 2 / Y/P
B/PR 2
Computer 3 / Y/P
B/PR 3
Wireless/Card
USB memory
Video
S-video A
B
Group Input signalFor PIP functionA: Main screen, B: Sub screen
A: Sub screen, B: Main screen
You cannot display two screens of the same group in the PIP mode.For SPLIT functionA, B or B, A is available.
You cannot display two screens of the same group in the SPLIT mode.
■Password function
When the password function is added and [Password] is set to [On], image projection
requires an entry of the preset password at power-on.
To add the password function, perform the following procedure:
(The password function, once added, cannot be deleted. Set [Password] to [Off] if you
do not want to use it after addition.)
Note: This password is different from that used for the wireless LAN.1
Set the projector to the operating status or the standby mode.
2
Keep pressing the 
 button for about 10 seconds until a beep
sounds.
The password function is added when the steps up to here have been completed. It
is also added to the Default setting menu.
Using handy features (Continued) 
						

							39
Operations
38
■The image adjustment menuUse this menu to set or adjust image-related items. Items that can be set or adjusted are
marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,
it indicates that you cannot select for the current input.)
Description
Digital (DVI)
Analog (D-SUB)(BNC)
    Item 
  
RGB Y/P
B/PRRGB Y/P
B/PRVideo
S-video PC card USB
 
ContrastAdjust the image contrast. Yes Yes Yes Yes Yes Yes Yes Yes
Lower
Higher
BrightnessAdjust the brightness of the image. Yes Yes Yes Yes Yes Yes Yes Yes
Darker
Brighter
ColorAdjust the color of the image. No Yes No Yes Yes Yes No No
Lighter
Deeper
Tint 
*1
Adjust the tint of the image color. No No No No Yes Yes No No
Reddish
Greenish
SharpnessAdjust the sharpness of the image. No Yes No Yes Yes Yes No No
Softer
Sharper
NoiseSet the function to reduce screen noise. No Yes No Yes Yes Yes No No
reduction
 
*2
On (Enable)
Off (Disable)
Picture modePress 
. Toggle the picture mode with 
 
.Yes Yes Yes Yes Yes Yes Yes Yes
Bright/Standard/True color
R-levelAdjust red of the image color. Yes Yes Yes Yes Yes Yes Yes Yes
Less red
More red
G-levelAdjust green of the image color. Yes Yes Yes Yes Yes Yes Yes Yes
Less green
More green
B-levelAdjust blue of the image color. Yes Yes Yes Yes Yes Yes Yes Yes
Less blue
More blue
NTSC mode
*3
Set the black level with 
 
.NoNoNoNo YesYesNoNo
US : NTSC (US) mode
JAPAN:NTSC (JAPAN) mode
 Auto settingAutomatically adjusts items such as the sampling No No Yes No No No No No
phase depending on the type of input signal. PhaseAdjust with 
  
 to eliminate flicker. No No Yes No No No No No
 FrequencyAdjust with 
  
 to eliminate periodic patterns No No Yes No No No No No
and flickering when many vertical lines appear on
the screen.
 H-positionAdjust the horizontal position of the image. No No Yes No No No No No
Move left
Move right
 V-positionAdjust the vertical position of the image. No No Yes No No No No No
Move down
Move up
You can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons 
p.16
 on the control panel (main unit side) and remote control.
■How to use the menus
The menu shown below is for operation instructions purposes and might differ from the
actual display.
Using the menus
Execute+16
+16
+16
+16
+16
+64
+64
+32
255
25530 StandardBrightness+12
Image adjustment
Contrast
Brightness
Picture mode
R-level
G-level
B-level
Auto setting
Phase
Frequency
H-position
V-position
Clamp 1
Clamp 2+12
+12
Bright
+12
+12
+12
+12
+12
+12
+12
+12
+12
To image adjustment menu
On
On
On
LanguageEnglish
StandardOff
Off
On
Manual
Low
1
Ye s
Key lockOff
Toggle items with            . 
Select items with             and press       . 
Fix selection with       .
Display the Setting display menu.
The Setting display (2) is displayed.
1. Press the MENU button
2. Select a Category
3. Adjustments & SettingsSelect a category by using  
         .
There are following five 
categories:Displays the current 
adjustments and 
settings of selected 
category.
Item shown with gray 
cannot be adjusted with 
the current input source.p.39
Image adjustment menu
p.41
Display setting menu
Default setting menu
p.44
Control setting menu
p.46
The figure shows displays given for operation instructions purposes.  As the display may differ depending on the item, use 
the following pages as a reference.
Item
Adjustment/Setting ValueThese marks signify 
the items can be 
adjusted/set by using
            
.
These marks signify the items can 
be selected from the list by using
            .
After an item is selected, apply it by 
pressing       .
Press       or       to open the menu.
Status display menu
p.48
p.53
These marks 
signify that there 
are options. 
Press        or         
to display a list of 
options.
These marks 
signify that 
there are setting 
screens. Press 
       or       to 
display a list of 
setting screens.
* When no item is 
changed, press       .
4. BackRETURN button
5. Press the MENU button.
6. EndPress the MENU button or RETURN button.
(The menu disappears 30 seconds after the last operation.)