Toshiba Satellite Pro Te2300 Manual

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
The Grand Tour
2-15TOSHIBA TE2300 DVD-RAM write  2 speed 
CD read 24 speed (maximum) 
CD-R write 16 speed (maximum) 
CD-RW write 8 speed (maximum) 
This drive supports the following formats: 
■ DVD-ROM  ■ DVD-Video 
■ CD-DA  ■ CD-Text 
■ Photo CD (single/multi-session) ■ CD-ROM Mode1, Mode2 
■ CD-ROM XA Mode2 (Form1, Form2) ■ Enhanced CD (CD-EXTRA) 
■ CD-G (Audio CD only)  ■ Addressing Method 2 
 
DVD Multi drives and disc are manufactured according to the 
specifications of six marketing regions. When you purchase DVD-Video, 
make sure it matches your drive, otherwise it will not play properly. 
Code Region 
1  Canada, United States 
2  Japan, Europe, South Africa, Middle East 
3  Southeast Asia, East Asia 
4  Australia, New Zealand, Pacific Islands, Central America, South 
America, Caribbean 
5  Russia, Indian Subcontinent, Africa, North Korea, Mongolia 
6 China 
 
 
Use the WinDVD 4 application to view DVD-Video discs. 
CD-R and DVD-R discs can be written only once. The recorded data 
cannot be erased or changed. 
CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi 
speed CDRW discs or high-speed 4- to 10-speed discs. The write speed 
of the high-speed CD-RW discs is maximum 10-speed. 
DVD-RW/-RAM discs can be recorded more than once. 
  
						

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
The Grand Tour
2-16TOSHIBA TE2300 
Slim Select Bay HDD adaptor (Black) 
You can increase your computer’s data storage capacity by installing an 
optional, integrated, 2 1/2 HDD in the Slim Select Bay. 
 
The Slim Select Bay HDD adaptor 
Slim Select Bay 2nd battery pack (Black) 
An optional battery pack can be installed in the Slim Select Bay to 
increase the computer’s battery power and operating time. For details, 
refer to the documentation accompanying the secondary battery pack. 
Refer to Chapter 8, Optional Devices, for details on installing a Slim Select 
Bay 2nd battery pack. 
 
The Slim Select Bay 2nd battery pack  
						

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
The Grand Tour
2-17TOSHIBA TE2300 
AC adaptor 
The AC adaptor converts AC power to DC power and reduces the voltage 
supplied to the computer. It can automatically adjust to any voltage from 
100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you 
to use the computer in almost any region. 
To recharge the battery, simply connect the AC adaptor to a power source 
and the computer. See Chapter 6, Power and Power-Up Modes, for 
details. 
 
The AC adaptor 
 
Use of the wrong adaptor could damage your computer. TOSHIBA 
assumes no liability for any damage in such case. The current rating for the computer is 5.0 amperes.  
						

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
The Grand Tour
3-18TOSHIBA TE2300 
3. Chapter 3 
Getting Started
This chapter provides basic information to get you started using your 
computer. It covers the following topics: 
■ Setting up your work space — for your health and safety 
 
Be sure also to read the Safety Instruction Manual. This guide, which is 
included with the computer, explains product liability. 
■ Connecting the AC adaptor 
■ Opening the display 
■ Turning on the power 
■ Starting up for the first time 
■ Turning off the power 
■ Restarting the computer 
■ Restoring the preinstalled software 
If you are a new user, follow the steps in each section of this chapter as 
you prepare to operate your computer.  
 
All users should be sure to carefully read the section Restoring the 
preinstalled software.  
 
 
TOSHIBA TE2300 
 User’s Manual 3-1  
						

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
Getting Started
3-2TOSHIBA TE2300 
Setting up your work space 
Establishing a comfortable work site is important for you and your 
computer. A poor work environment or stressful work habits can result in 
discomfort or serious injury from repetitive strain to your hands, wrists or 
other joints. Proper ambient conditions should also be maintained for the 
computer’s operation. This section discusses the following topics: 
■  General conditions 
■  Placement of the computer and peripheral devices 
■  Seating and posture 
■  Lighting 
■  Wo r k  h a b i t s  
General conditions 
In general, if you are comfortable, so is your computer, but read the 
following to make sure your work site provides a proper environment. 
■ Make sure there is adequate space around the computer for proper 
ventilation. 
■  Make sure the AC power cord connects to an outlet that is close to 
the computer and easily accessible. 
■  The temperature should be 5 to 35 degrees Centigrade (41 to 
95 degrees Fahrenheit) and the relative humidity should be 20 to 
80 percent. 
■  Avoid areas where rapid or extreme changes in temperature or 
humidity may occur. 
■  Keep the computer free of dust, moisture, and exposure to direct 
sunlight. 
■  Keep the computer away from heat sources, such as electric heaters. 
■  Do not use the computer near liquids or corrosive chemicals. 
■  Do not place the computer near objects that create strong magnetic 
fields (e.g., stereo speakers). 
■  Do not operate the computer in close proximity to a mobile phone. 
■  Leave ample ventilation room for the fan. Do not block the vents. 
Placement of computer 
Position the computer and peripheral devices to provide comfort and 
safety. 
■ Set the computer on a flat surface at a comfortable height and 
distance. The display should be no higher than eye level to avoid eye 
strain.  
						

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
Getting Started
3-3TOSHIBA TE2300 ■ Place the computer so that it is directly in front of you when you work 
and make sure you have adequate space to easily operate other 
devices. 
■ Allow adequate space behind the computer to let you freely adjust the 
display. The display should be angled to reduce glare and maximize 
visibility. 
■ If you use a paper holder, set it at about the same height and distance 
as the computer. 
Seating and posture 
The height of your chair in relation to the computer and keyboard as well 
as the support it gives your body are primary factors in reducing work 
strain. Refer to the following tips and to the figure below. 
 
Posture and positioning of the computer 
■ Place your chair so that the keyboard is at or slightly below the level of 
your elbow. You should be able to type comfortably with your 
shoulders relaxed. 
■ Your knees should be slightly higher than your hips. If necessary, use 
a foot rest to raise the level of your knees to ease pressure on the 
back of your thighs. 
■ Adjust the back of your chair so it supports the lower curve of your 
spine. 
■ Sit straight so that your knees, hips and elbows form approximately 
90 degree angles when you work. Do not slump forward or lean back 
too far. 
90° ANGLES 
BELOW EYE 
LEVEL  
FOOT REST  
						

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
Getting Started
3-4TOSHIBA TE2300 
Lighting 
Proper lighting can improve legibility of the display and reduce eye strain. 
■ Position the computer so that sunlight or bright indoor lighting does 
not reflect off the screen. Use tinted windows, shades or other screen 
to eliminate sun glare. 
■ Avoid placing the computer in front of bright light that could shine 
directly in your eyes. 
■ If possible, use soft, indirect lighting in your computer work area. Use 
a lamp to illuminate your documents or desk, but be sure to position 
the lamp so that it does not reflect off the display or shine in your 
eyes. 
Work habits 
A key to avoiding discomfort or injury from repetitive strain is to vary your 
activities. If possible, schedule a variety of tasks into your work day. If you 
must spend long periods at the computer, finding ways to break up the 
routine can reduce stress and improve your efficiency. 
■ Sit in a relaxed posture. Good positioning of your chair and equipment 
as described earlier can reduce tension in your shoulders or neck and 
ease back strain. 
■ Vary your posture frequently. 
■ Occasionally stand up and stretch or exercise briefly. 
■ Exercise and stretch your wrists and hands a number of times during 
the day. 
■ Frequently, look away from the computer and focus your eyes on a 
distant object for several seconds, for example 30 seconds every 15 
minutes. 
■ Take frequent short breaks instead of one or two long breaks, for 
example, two or three minutes every half hour. 
■ Have your eyes examined regularly and visit a doctor promptly, if you 
suspect you might be suffering from a repetitive strain injury. 
A number of books are available on ergonomics and repetitive strain injury 
or repetitive stress syndrome. For more information on these topics or for 
pointers on exercises for such stress points as hands and wrists, please 
check with your library or book vendor. Also refer to the computer’s 
Safety Instruction Manual. 
  
						

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
Getting Started
3-5TOSHIBA TE2300 
Connecting the AC adaptor 
Attach the AC adaptor when you need to charge the battery or you want 
to operate from AC power. It is also the fastest way to get started, 
because the battery pack will need to be charged before you can operate 
from battery power. 
The AC adaptor can be connected to any power source supplying from 
100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor 
to charge the battery pack, refer to Chapter 6, Power and Power-Up 
Modes. 
 
Use of the wrong adaptor could damage your computer. TOSHIBA 
assumes no liability for any damage in such case. The current rating for the computer is 5.0 amperes. 
  1.  Connect the power cord to the AC adaptor. 
 
Connecting the power cord to the AC adaptor 
  2.  Connect the AC adaptor’s DC output plug to the DC IN port on the 
back side of the computer. 
 
Connecting the adaptor to the computer 
  3.  Plug the power cord into a live wall outlet. The Battery and DC IN 
indicator on the front of the computer should glow.  
						

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
Getting Started
3-6TOSHIBA TE2300 
Opening the display 
The display panel can be rotated in a wide range of angles for optimal 
viewing. 
  1.  Slide the display latch on the front of the computer to the right to 
unlatch the display panel. 
  2.  Lift the panel up and adjust it to the best viewing angle for you. 
 
When you open the display, hold it with both hands and lift up slowly. 
 
Opening the display panel 
Turning on the power 
This section describes how to turn on the power. 
 
After you turn on the power for the first time, do not turn it off until you 
have set up the operating system (OS) and the OS has started up. 
  1.  If an external diskette drive is connected, make sure it is empty. If a 
diskette is in the drive, press the eject button and remove the 
diskette. 
  2.  Open the display panel. 
  3.  Press and hold the button for two or three seconds. 
 
 Turning on the power D
ISPLAY 
LATCH  
						

							 
 
 
TE2300 Ve r s io n  1Last Saved on 21.05.2003 10:18
ENGLISH using TE2300_Onine.dot –– Printed on 27.05.2003 as  
Getting Started
3-7TOSHIBA TE2300 
Starting up for the first time 
When you first turn on the power, the computer’s initial screen is the 
Microsoft Windows® XP Professional Startup Screen Logo. 
Follow the on-screen directions.  
Turning off the power 
The power can be turned off in one of the following modes: Shut down 
(Boot), Hibernation or Standby mode. 
Shut Down mode (Boot mode) 
When you turn off the power in Shut Down mode, no data is saved and 
the computer will boot to the operating system’s main screen. 
  1.  If you have entered data, save it to the hard disk or to a diskette. 
  2.  Make sure all disk(disc)activity has stopped, then remove any 
CD/DVDs or diskette. 
 
Make sure the Disk, Slim Select Bay and Slim Select Bay’s module 
indicators are off. If you turn off the power while a disk (disc) is being accessed, you can lose data or damage the disk(disc). 
  3.  Click start then click Turn off computer. From the Tu r n  o f f  
computer menu select Tu r n  o f f. 
  4.  Turn off the power to any peripheral devices. 
 
Do not turn the computer or devices back on immediately. Wait a moment 
to let all capacitors fully discharge. 
Hibernation mode 
The hibernation feature saves the contents of memory to the hard disk 
when the computer is turned off. The next time the computer is turned on, 
the previous state is restored. The hibernation feature does not save the 
status of peripheral devices. 
 
1.   While entering hibernation mode, the computer saves the contents of 
memory to the HDD. Data will be lost if you remove the battery or 
disconnect the AC adaptor before the save is completed. Wait for the Disk indicator to go out. 
2.   Do not install or remove a memory module while the computer is in 
hibernation mode. Data will be lost.