Toshiba Satellite L300 L305 Maintenance Manual

4 Replacement Procedures  4.1 General 
Removing the Memory Card 
Remove the memory card according to the following procedures and Figure 4-3, after 
checking that the computer is turned off in boot mode. 
1. Open the card cover. 
2. Push the memory card to be removed until it stops then release the memory card. 
3. When the memory card pops out, grasp it and pull it out. 
Memory card
 
Figure 4-3 Removing the memory card 
 
4-12 Satellite L300/L305/ Satellite Pro  L300/ EQUIUM L300/ SATEGO L300...

4.1 General   4 Replacement Procedures 
Satellite L300/L305/ Satellite Pro  L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-13 
Installing the Memory Card 
Install the memory card according to the following procedures and Figure 4-3, after chec\
king 
that the computer is turned off in boot mode. 
1. Insert the memory card gently until it stops and is seated securely. 
2. Checking that the memory card is seated securely. 
After the PC card is installed, check the  hardware configuration in the...

4 Replacement Procedures  4.1 General 
Removing the Optional Memory 
Remove the optional memory (module) according to the following procedures and Figures 4-
4, after checking that the computer is turned off in boot mode. 
CAUTION: Remove the optional memory after turning off the computer. If t\
his is 
violated, the computer or memory can be damaged. 
1. Turn the computer upside down. 
2. Release one optional memory cover securing the screw. 
3. Remove the memory cover. 
CAUTION:  Do not touch the...

4.1 General   4 Replacement Procedures 
Satellite L300/L305/ Satellite Pro  L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 4-15 
Installing the Optional Memory 
Install the optional memory (module) according to the following procedures and Figures 4-4, 
after checking that the computer is turned off in boot mode. 
Note: The slot A is reserved for main memory. Use the slot B for expanded memory. If 
only one card is installed, use the slot A. 
CAUTION:  Install the optional memory afte r turning off...

4 Replacement Procedures  4.2 HDD 
4.2 HDD 
Removing the HDD  
 
CAUTION:  Do not press on the top or bottom of the drive.  
Applying such pressure can either corrupt the data in the drive or  
damage the drive. 
 
 
Remove the HDD (hard disk drive) according to the following procedures and Figures 4-5, 4-
6. 
1. Release the two HDD cover screws securing the HDD cover. 
2. Remove the HDD cover. 
HDD cover
HDD cover secure screw
HDD pack
 
Figure 4-5 Removing the HDD pack 
4-16 Satellite L300/L305/...

4.2 HDD  4 Replacement Procedures 
3. Remove the HDD pack by pulling on the tab attached to the pack, following t\
he 
direction of the arrows. 
NOTE:  Do not disassemble the HDD pack when it is working normally.  Dis\
assemble 
or replace the HDD pack only if it fails. 
4. Place the HDD pack on a flat surface (such as a desk), and remove the two M3x4 
black flat head screws with M3x4 black head screws. 
5. Place the HDD pack on a flat surface (such as a desk), and remove the chassis. 
M3x4 Black
flat...

4 Replacement Procedures  4.2 HDD 
4-18 Satellite L300/L305/ Satellite Pro L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 
Installing the HDD 
Install the HDD according to the following procedures and Figures 4-5, 4\
-6. 
CAUTION:  To avoid damage, always hold the HDD only by its sides. 
1. Attach the HDD chassis. 
2. Secure the HDD and its chassis with the two M3x4 black flat head screws \
with M3x4 
white head screws. 
CAUTION:  To prevent the HDD bracket from being distorted when installin\
g the...

4.3 ODD Bay Module  4 Replacement Procedures 
4.3  ODD Bay Module 
Removing the ODD Bay Module 
NOTE:  The installation and removal procedures are the same for all the \
modules that 
can be installed in the ODD bay. See the appropriate sections for the di\
sassembly 
procedures of specific modules.  
Remove the ODD bay module according to the following procedures and Figures 4-7. 
1. Turn the computer upside down. 
2. Remove the M2.5x6 black flat head screw. 
3. Push out on the ODD bay module in the...

4 Replacement Procedures  4.3 ODD Bay Module 
4-20 Satellite L300/L305/ Satellite Pro  L300/ EQUIUM L300/ SATEGO L300 Maintenance Manual 
Installing the ODD Bay Module 
Install the ODD bay module according to the following procedures and Figures 4-7. 
1. Place the ODD bay module in the correct position and slide it in. 
2. Push it in until it clicks into place. 
3. Secure the ODD bay module with one M2x5 black flat head screw.  

4.3 ODD Bay Module  4 Replacement Procedures 
Disassembling the ODD Drive 
NOTE:  Do not disassemble the ODD drive when it is working normally. Dis\
assemble 
or replace the ODD drive only if it fails. 
Disassemble the ODD drive according to the following procedures and Figure 4-8. 
1. Remove two  M2x3 black flat head screws. 
2. Remove  the bracket. 
 
Bracket
M2x3 flat head screw
black ODD bay module
 
Figure 4-8  Removing the bracket from the ODD drive 
 
Assembling the ODD Drive 
Assemble the ODD...