Toshiba Satellite C55-b Manual

							2. Plug one end of the cable into the LAN jack. Press gently until youhear the latch click into place. Figure 4-5 Connecting the LAN cable1. LAN jack2. LAN cable
3. Plug the other end of the cable into a LAN hub connector or router.
Check with your LAN administrator and hardware or software vendorbefore using or configuring a network connection.
Memory media The computer is equipped with a memory media slot that canaccommodate some kinds of memory media with various memory
capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants.
Keep foreign objects out of the memory media slot. Never allow metal
objects, such as screws, staples and paper clips, to enter the computer or Keyboard. Foreign metal objects can create a short circuit, which cancause computer damage and fire, possibly resulting in serious injury.Please note that an adaptor is required to use miniSD/microSD Card.
Please note that not all memory media have been tested and verifiedto work correctly. Therefore, it is not possible to guarantee that allmemory media will operate properly.
Figure 4-6 Examples of memory media
 Secure Digital (SD) Card microSD card adaptor and
microSD card  MultiMediaCard (MMC)  
User's Manual 4-2421     
						

							Points to note about the memory media cardSD/SDHC/SDXC memory cards comply with SDMI (Secure Digital MusicInitiative), which is a technology adopted to prevent unlawful copy or
playback of digital music. For this reason, you cannot copy or playback
protected material on another computer or other device, and you may not
reproduce any copyrighted material except for your personal enjoyment.
Below is a simple explanation for distinguishing SD memory cards from SDHC memory cards and SDXC memory cards.
SD, SDHC and SDXC memory cards appear the same externally.
However, the logo on memory cards is different, so pay careful
attention to the logo when purchasing.
The SD memory card logo is ().
The SDHC memory card logo is ().
The SDXC memory card logo is ().
The maximum capacity of SD memory cards is 2GB. The maximum
capacity of SDHC memory cards is 32GB. The maximum capacity of
SDXC memory cards is 128GB.
Memory media format New media cards are formatted according to specific standards. If you wish
to reformat a media card, be sure to do so with a device that uses media cards.
Formatting a memory media card
Memory media cards are sold already formatted in conformity to specific
standards. If you reformat a memory card, be sure to reformat it with a
device such as digital camera or digital audio player that uses the memory
cards, not with the format command provided within Windows.
Should you need to format all areas of the memory card, including the
protected area, you will need to obtain an appropriate application that applies the copy protection system.
Media care
Observe the following precautions when handling the card.
Do not twist or bend cards.
Do not expose cards to liquids or store in humid areas or lay media
close to containers of liquid.
Do not touch the metal part of a card or expose it to liquids or let it get
dirty.
After using card, return it to its case.
User's Manual 4-25    
						

							The card is designed so that it can be inserted only one way. Do nottry to force the card into the slot.
Do not leave a card partially inserted in the slot. Press the card untilyou hear it click into place.
Set the write-protect switch to the lock position, if you do not want to
record data.
Memory cards have a limited lifespan, so it is important to backup
important data.
Do not write to a card if the battery power is low. Low power could
affect writing accuracy.
Do not remove a card while read/write is in progress.
For more details on using memory cards, see manuals accompanying the cards.
About the write-protect feature
Memory media cards have a write-protect function.
SD Card (SD memory card, SDHC memory card and SDXC memory
card)
Set the write-protect switch to the lock position, if you do not want to record
data.
Inserting memory media
The following instructions apply to all types of supported media devices. To
insert memory media, follow the steps as detailed below:
1. Turn the memory media so that the contacts (metal areas) face down.2. Insert the memory media into the memory media slot on the computer.
User's Manual 4-26 
						

							3. Press the memory media gently to ensure a firm connection is made.The memory media will be partially out of the slot.
Figure 4-7 Inserting memory media1. Memory media slot*2. Memory media
* One Memory media slot is provided either on the front or on the left side of
your computer.
Product appearance depends on the model you purchased.
Make sure the memory media is oriented properly before you insert it.
If you insert the media in wrong direction, you may not be able toremove it.
When inserting the memory media, do not touch the metal contacts.You could expose the storage area to static electricity, which candestroy data.
Do not turn the computer off or switch to Sleep Mode or HibernationMode while files are being copied - doing so may cause data to be
lost.
Removing memory media
The following instructions apply to all types of supported media devices. To
remove memory media, follow the steps as detailed below:
1. Click the  Safely Remove Hardware and Eject Media  icon on the
Windows Taskbar.
2. Select  memory media .
3. Grasp the media and remove it.
If you remove the memory media or turn off the power while the
computer is accessing the memory media, you may lose data or
damage the media.
Do not remove the memory media while the computer is in Sleep or Hibernation Mode. The computer could become unstable or data inthe memory media could be lost.
Do not remove only the miniSD/microSD Card while leaving the
adaptor in the memory media slot.
User's Manual 4-2712  
						

							External DisplayYour computer video capabilities can be enhanced with additional displays.External displays allows you to share your desktop or extend the desktoparea.
Connecting an external display Your computer comes with a built-in display, but you can also connectother external displays via available ports on the computer.Some models may include the Triple Monitor function that can display
image on Triple Monitor independently.
As the port operation of all external display devices have not been
confirmed, some devices may not function properly.
External RGB monitor port
An external analog monitor can be connected to the External RGB monitor
port on the computer. To connect an external analog monitor, follow the steps as detailed below:
1. Connect the RGB cable to the External RGB monitor port. Figure 4-8 Connecting the RGB cable to the External RGB monitor port
1. External RGB monitor port2. RGB cableThere are no fastening screws for an external monitor cable on the
External RGB monitor port. However, external monitor cables which have connectors with fastening screws can still be used.
2. Turn the external monitor's power on.
When you turn on the power, the computer will automatically recognize the
monitor and determine whether it is a color or monochrome device.
When displaying desktop on an external analog monitor, desktop is sometimes displayed on the center of the monitor with black bars around
desktop (with small size).
At that time, please read the manual of the monitor and set the display mode which is supporting at the monitor. Then it will be displayed with
suitable size with correct aspect ratio.
User's Manual 4-2821  
						

							The HDMI out port
HDMI (High-Definition Multimedia Interface) port digitally transfers bothvideo and audio data without reducing the quality. HDMI-compatible external display devices including televisions can be connected via theHDMI port.
Some models can support ultra high definition (3840 x 2160 pixels) display
on compatible external display devices via HDMI output port. To use this
function, you must purchase an HDMI cable (corresponding to 3840x2160
pixels or higher).
To connect an HDMI-compatible display device, follow the steps as
detailed below:
To connect a device to the HDMI out port, you must purchase a suitable
HDMI cable.
1. Plug one end of the HDMI cable into the HDMI in port of the HDMI display device.
2. Plug the other end of the HDMI cable into the HDMI out port on your computer.
3. Turn the HDMI display device's power on.
Figure 4-9 Connecting the HDMI out port
1. HDMI out port2. HDMI cablePlease do not plug/unplug an HDMI device under the following conditions:
The system is starting up.
The system is shutting down.
When you connect a television or external monitor to the HDMI port, the
display output device is set to HDMI.
When you unplug the HDMI cable and re-plug it, please wait at least 5
seconds before you re-plug the HDMI cable again.
When you change the display output device, the playback device may not switch automatically. In this case, in order to set the playback device to the
User's Manual 4-2921  
						

							same device as the display output device, please adjust the playbackdevice manually by the following steps:
1. Click  Start -> Control Panel -> Hardware and Sound -> Sound .
2. In the  Playback  tab, select the playback device which you want to
switch to.
3. To use the internal speakers on your computer, select  Speakers. To use
the television or the external monitor that you have connected to the computer, select a different playback device.
4. Click the  Set Default button.
5. Click  OK to close the  Sound dialog.
Settings for display video on HDMI
To view video on the HDMI display device, be sure to configure the
following settings otherwise you may find that nothing is displayed.
Be sure to use the function key to select the display device before starting
to play video. Do not change the display device or audio device while playing media files.
Do not change the display device under the following conditions.
While data is being read or written.
While communication is being carried out.
Selecting HD Format
To select the display mode, follow the steps as below:
1. Click  Start -> Control Panel -> Appearance and Personalization ->
Display -> Change display settings -> Advanced settings -> List 
All Modes .
2. Select one of the modes at  List All Modes.
Changing the display settings After one or more external displays are connected, the operating systemcan automatically detect, identify and setup the display settings.
You can also manually manage how the external displays will work and change the display settings by pressing  P while holding down the
Windows  ( 
 ) key. If you disconnect the external display before you turn
the computer's power off, be sure to switch to the internal display.
Security lock A security lock enables you to anchor your computer to a desk or other
heavy object in order to help prevent unauthorized removal or theft. The
computer has a security lock slot on its right side into which you can attach
User's Manual 4-30  
						

							one end of the security cable, while the other end attaches to a desk or
similar object. The methods used for attaching security cables differ from
product to product. Please refer to the instructions for the product you are
using for more information.
Connecting the security lock In order to connect a security cable to the computer, follow the steps as
detailed below:
1. Turn the computer so its right side faces you.
2. Align the security cable with the lock slot and secure it in place.
Figure 4-10 Security lock1. Security lock slot2. Security lock
Optional TOSHIBA Accessories
You are able to add a number of options and accessories in order to make
your computer even more powerful and convenient to use. For reference,
the following list details some of the items that are available from your
reseller or TOSHIBA dealer:
Universal AC AdaptorIf you frequently use your computer at more than
one site, it may be convenient to purchase an additional AC adaptor to be kept at each site in
order to remove the need to always carry the
adaptor with you.
Sound System and Video mode
This section describes some of the audio control functions.
Volume Mixer The Volume Mixer utility lets you control the audio volume for playback ofdevices and applications under Windows.
To launch the Volume Mixer utility, right click on the speaker icon on
the Windows Taskbar, and then select  Open Volume Mixer from the
sub menu.
User's Manual 4-311
2  
						

							To adjust the volume level of speakers or headphones, move the
Speakers  slider.
To adjust the volume level of an application that you are using, move
the slider for the corresponding application.
Microphone Level Follow the steps below to change the microphone recording level.1. Right click on the speaker icon on the Windows Taskbar, and select Recording devices  from the sub menu.
2. Select  Microphone , and click Properties .
3. On the  Levels tab move the  Microphone slider to increase or
decrease the microphone volume level.
If you feel the microphone volume level is inadequate, move the
Microphone Boost  slider to a higher level.
Audio Enhancements In order to apply the sound effects for your current speaker, follow the
steps below.
1. Right click on the  Speakers icon on the Windows Taskbar, and then
select  Playback devices  from the sub menu.
2. Select  Speakers, and click  Properties .
3. On the  Enhancements  tab select the sound effects you would like,
and click  Apply.
DTS Sound DTS Sound™ utilizes advanced patented techniques to retrieve audio cuesburied in the original source material and deliver immersive surround sound complete with deep, rich bass and crystal clear dialog.
DTS Sound is provided with some models. It provides the following
features:
Immersive surround sound with bass and dialog enhancement
Broad sweet spot with elevated sound image
Improved volume output delivering maximum volume without creating
clipping or distortion
Dialog enhancement for clear and intelligible vocals
Bass enhancement for rich, low frequency production
High frequency definition for crisp details
To access the utility, click  Start -> All Programs -> DTS, Inc -> DTS 
Sound .
U.S. patents apply to this product. See
http://patents.dts.com
Manufactured under license from DTS Licensing Limited.
User's Manual 4-32 
						

							Video modeVideo mode settings are configured via the  Screen Resolution dialog.
To open the  Screen Resolution  dialog, click Start -> Control Panel ->
Appearance and Personalization -> Display -> Change display  settings .If you are running some applications (for example a 3D application or video
playback), you may see some disturbance, flickering or frame dropping on
your screen.
If that occurs, adjust the resolution of display, lowering it until the screen is
displayed properly.User's Manual 4-33