Toshiba Projector Tlp X21u User Manual

31
Operations
CONTENTS
Turning the power off
Press ON/STANDBY after using the projector.An instruction message appears.Press ON/STANDBY again.Cooling starts. Once cooling is completed, the LAMP and FAN
indicators turn off and the standby mode is set. (The ON
indicator turns in orange.)
To protect the light source lamp, the LAMP indicator blinks as long as
a minimum of cooling is necessary. The power cannot be turned back
on during this time. Unplugging the power cord at this time will shorten
the lampÕs...

32
Operations
CONTENTS
Notes
¥ Automatic adjustment may not be performed properly for signals other than the RGB signals
with which the projector is compatible 
91
.
¥ The horizontal position, vertical position, sampling phase and sampling frequency can also be
adjusted from the menu screen 
54
.
* Sampling frequency
Analog RGB signals input from the computer are converted into digital signals inside the
projector. The sampling frequency is the number of times per second the analog signals are
converted...

33
Operations
CONTENTS
Correcting the keystone distortion
A picture may be expanded on the upper side if projected upward from the projector lifted
up by the foot adjuster. The projector can correct this keystone distortion automatically.
MENUON/STANDBY INPUT
L-CLICK R-CLICK
ENTERKEYSTONE
AUTO
SET
EXIT
PIPFREEZEMUTE CALL
RESIZE
VOLUME/ADJUST
TEMP
LAMP ON
BUSY FANKEYSTONESET AUTO AUTO
KEYSTONEAUTO
EXIT ENTER
MENUINPUTVOL/ADJ.TEMPLAMP ONBUSY FANON/STANDBY
KEYSTONESET AUTO AUTOEXIT ENTERMENUINPUT...

34
Operations
CONTENTS
Cutting off the picture and sound temporarily
The image and sound of this projector can be turned off if you wish to temporarily project
the image of another projector or a OHP, etc., on the screen.
Note
The mute mode is cancelled if another operation is performed during the mute mode.
MENUON/STANDBY INPUT
L-CLICK R-CLICK
ENTERKEYSTONE
AUTO
SET
EXIT
PIPFREEZEMUTE
MUTECALL
RESIZE
VOLUME/ADJUSTLASER
MUTE
Press MUTE.The sound and picture are cut off temporarily.
To cancel the mute...

35
Operations
CONTENTS
Freezing the picture
You can freeze the image being projected.
Use this function to stop images from a video recorder to make presentations.
Notes
¥ The freeze mode is cancelled if any other operation is performed during the freeze mode.
¥ You can not use the FREEZE button when the memory card input is selected.
¥ The freeze mode cannot be set when there is no input (when no signals are being supplied
from a signal source).
¥ The input sourceÕs image continues to play even when the...

36
Operations
CONTENTS
You can enlarge (resize) the picture size projected.
Enlarging the picture size
Press RESIZE (
).
The enlargement ratio increases each time the RESIZE (
)
button is pressed.
The enlargement ratio can be increased continuously by keeping the
button pressed in.To reduce the enlargement ratio, press the RESIZE (
) button.
The enlargement ratio can be reduced continuously by keeping the button
pressed in.The enlarged section is moved when the selection buttons
(
 / 
 / 
 / 
) are...

37
Operations
CONTENTS
Press PIP.A sub-picture is displayed.
Press the PIP button again to turn off the sub-picture.
Video or S-video images can be displayed as small images on the computerÕs image.
(Referred to as Òsub-picturesÓ in this manual.)
Notes
¥ The PIP function cannot be used when a source other than an RGB input source is selected.
¥ The PIP function cannot be used with no signals supplied from an RGB signal source.
¥ The sub-picture turns off if any other operation is performed.
¥ The signal...

38
Operations
CONTENTS
CALL
Notes
¥ The information displayed is not refreshed even if it changes. To refresh the information, turn
off the information display, then turn it back on.
¥ The information display turns off if any other operation is performed.
¥ The ÒLamp timeÓ shows an approximate time for lamp replacement. (It should not be used as a
lamp warranty time counter.) If the time indicated here nears 1000, contact your store of
purchase about obtaining a replacement lamp (TLPLX10, sold...

39
Operations
CONTENTS
Operating a computer by the remote control
Notes
¥ This function is available with Windows98 and Mac OS9 computers equipped with a USB port as standard.
¥ When connecting the computerÕs USB port for the first time, a message asking you to insert the Windows98 CD-ROM may appear on the computerÕs
monitor screen, depending on whether or not the device driver is installed. If so, do as the message says.
¥ When using a USB cable other than the supplied one, be sure to use a shielded...

40
Operations
CONTENTS
This projector can read the image data of JPEG format stored in a memory card to project the images on the screen.
For example, you can perform the presentation without a computer by converting the presentation data prepared on the computer into JPEG format
and then saving in the memory card. (It cannot reproduce the motion in the same manner of the Microsoft PowerPoint animated effect.)
Read this page carefully before using this function.
Projecting images stored in a memory card...