Toshiba Projector Tlp X11u User Manual

							21
Installation and
connection
CONTENTS
Ceiling-mounted front projectionViewing a picture projected on the front of the screen from a
ceiling installation.
Ceiling-mounted rear projectionViewing a picture projected through the back of the screen from a
ceiling installation.
Perform the ÒProjection modeÓ setting on the menu screen for the projection method. 
67
Notes
¥ For models with a document imaging camera, the ceiling-mounting is not recommended, since the camera arm may hang down if the projector is
suspended from the ceiling.
¥ The relation between the projection size and the distance to the screen is the same as that of the floor-mounted projection mode 
18
.
Translucent screen Viewer
Ceiling-mounted projector placement
CAUTION
When a ceiling mount is required, please consult with the dealer.
Viewer 
						

							22
Installation and
connection
CONTENTS
Notes
¥ The projector cannot be connected to a computer without an analog RGB connector. For details, refer to the computer manual.
¥ When connecting to a Macintosh computer, use the supplied Mac adapter (Multiple Scan 21 compatible). For some models the adapter is not required.
¥ You may not be able to connect some computers to the projector. For details, consult the dealer.
¥ Some computers may have output modes which are not compatible with this projector. Check the compatibility of the connectors, signal levels, timing,
resolutions, etc.
Connecting a computer
You can project the picture from the computer.
Check that the power for the projector and computer is off before connecting the cables.
USB MONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2
CONTROLS-VIDEO VIDEO
VIDEO INR - AUDIO - LAUDIO
IN AUDIO
OUT
USB MONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROL
S-VIDEO VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN AUDIO
OUT
COMPUTER IN 1 Connector
For use as both analog RGB1 input and Y/P
B/PR input. At shipping from 
factory, it is set for use as analog RGB1 input.
AUDIO IN jack
For use as both audio signals for RGB input (analog RGB1/analog 
RGB2/digital RGB) and Y/P
B/PR input.
ø3.5mm Stereo mini-jack
To audio output port RGB cable (supplied)
To AUDIO IN jackComputer
To COMPUTER IN 1 connector
Be sure to connect in the proper 
direction.
To monitor port (      )
Audio cable (supplied)Connecting a Mac adapter for 
Macintosh computers (supplied) 
						

							23
Installation and
connection
CONTENTS
Connecting a computer with DVI output connector
Notes
¥ The COMPUTER IN 2 connector can be used to input either digital RGB or analog RGB signals, depending on the connection cable used.
The projectorÕs DVI connector is of the DVI analog & digital type. Check the type of output connector on the computer, then purchase the appropriate type
of connection cable.  (To input analog RGB signals from a computer without a DVI connector, use a DVI cable on which the computer side connector is a
mini D-sub 15-pin connector.)
¥ You may not be able to connect some computers to the projector. For details, consult the dealer.
¥ Some computers may have output modes which are not compatible with this projector. Check the compatibility of the connectors, signal timing,
resolutions, etc.You can project the picture by entering the digital RGB signals from a computer with DVI output connector.
Check that the power for the projector and computer is off before connecting the cables.
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROLS-VIDEO VIDEO
VIDEO INR - AUDIO - LAUDIO
IN AUDIO
OUT
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROL
S-VIDEO VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN AUDIO
OUT
48
COMPUTER IN 2 Connector (DVI connector)
For use as both analog RGB2 input and digital RGB input. At shipping from 
factory, the projector is set so that this connector cannot be selected by the 
INPUT button. Change the setting on the menu screen when using.
AUDIO IN jack
For use as both audio signals for RGB input (analog RGB1/analog 
RGB2/digital RGB) and Y/P
B/PR input.
ø3.5mm Stereo mini-jack
To audio output port DVI cable (not supplied)
To AUDIO IN jackComputer To COMPUTER IN 2 connector
Be sure to connect in the proper 
direction.
To DVI output port
Audio cable (supplied) 
						

							24
Installation and
connection
CONTENTS
Connecting video equipment
Note
The S-VIDEO connector and VIDEO jack can be used independently, but the audio input jacks are used as both the S-VIDEO and VIDEO input.You can project the picture from video equipment by using VIDEO IN connectors.
Check that the power for the projector and video equipment is off before connecting the cables.
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROLS-VIDEO VIDEO
VIDEO INR - AUDIO - LAUDIO
IN AUDIO
OUT
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROL
S-VIDEO VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN AUDIO
OUT
48
S-VIDEO connector
At shipping from factory, the projector is set so that this connector cannot be 
selected by the INPUT button. 
Change the setting on the menu screen when using.
Pin plug (red)
To audio output (R)
(Yellow) To VIDEO jack To S-VIDEO connector
Be sure to connect in the proper 
direction.
To S-video output
AV cable (supplied)Pin plug (white)
To audio output (L) Video equipment
Pin plug (yellow)
To video output (White) To AUDIO-L jack (Red) To AUDIO-R jackS-video cable
(not supplied)
Continued 
						

							25
Installation and
connection
CONTENTS
Connecting video equipment (continued)
Note
Some component video signal sources include the Y/C
B/CR signals of a DVD player and the Y/P
B/PR signals of high definition devices, etc.
You can project the picture from video equipment with component video output jack.
Check that the power for the projector and video equipment is off before connecting the cables.
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROLS-VIDEO VIDEO
VIDEO INR - AUDIO - LAUDIO
IN AUDIO
OUT
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROL
S-VIDEO VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN AUDIO
OUT
48
Video equipment with component 
video output jack. (DVD player, etc.) COMPUTER IN 1 Connector
For use as both analog RGB1 input and Y/P
B/PR input. At shipping from 
factory, it is set for use as analog RGB1 input.
Change the setting on the menu when using as Y/P
B/PR input.
AUDIO IN jack
For use as both audio signals for RGB input (analog RGB1/analog 
RGB2/digital RGB) and Y/P
B/PR input.
Pin plug (red)
To audio output (R)
To AUDIO IN jackTo COMPUTER IN 1 connector
Be sure to connect in the proper 
direction.Adapter
BNC-pin
(Not supplied)
Audio cable (not supplied) Monitor cable 
Mini D-sub 15P-BNC
(Not supplied)
Pin plug (white)
To audio output (L) (Blue) To P
B (CB) video output (Green) To Y video output
(Red) To PR (CR) video output 
						

							26
Installation and
connection
CONTENTS
Projector operation control by a computer
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROLS-VIDEO VIDEO
VIDEO INR - AUDIO - LAUDIO
IN AUDIO
OUT
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROL
S-VIDEO VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN AUDIO
OUT
Computer
To RS-232C port Control cable (supplied) To CONTROL connector
Be sure to connect in the proper 
direction.
You can control the projector by a computer connected with the control cable supplied. 
93
Check that the power for the projector and computer is off before connecting the cables.
Note
Do not connect a cable other than the exclusive one supplied. 
						

							27
Installation and
connection
CONTENTS
How to use the output connector
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROLS-VIDEO VIDEO
VIDEO INR - AUDIO - LAUDIO
IN AUDIO
OUT
USBMONITOR OUT
COMPUTER IN 1(
Y/PB/PR )
COMPUTER IN 2 CONTROL
S-VIDEO VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN AUDIO
OUT
Pin plug (red)
To audio input (R)
To AUDIO OUT jackTo MONITOR OUT connector
Be sure to connect in the proper 
direction.
Audio cable (not supplied)Stereo system, etc. Computer monitor, etc.
Pin plug (white)
To audio input (L)
You can output video and audio signals to a computer monitor, a stereo system, etc.
Check that the power for the projector and the equipments is off before connecting the cables.
Notes
¥ The audio signals of the input source selected by the input select operation are output from the AUDIO OUT jack.  The signal level (volume) is fixed.
¥ The analog RGB signals of the COMPUTER IN 1 or COMPUTER IN 2 connector selected by the input select operation are output from the MONITOR
OUT connector. If neither of these input sources is selected, the analog RGB signal of the COMPUTER IN 1 connector is output.  (Digital RGB signals
are not output.)
¥ Signals are output from the MONITOR OUT connector even when in the standby mode.
¥ Do not turn the projector on or off with the stereo system, etc., turned on.  This may damage the stereoÕs speakers. 
						

							28
Operations
CONTENTS
Preparation1
Install and connect the projector properly.
2
Take off the lens cover.
Press ON/STANDBY.The projector turns on and the ON, LAMP and FAN indicators
light in green.
(The LAMP indicator blinks while the lamp is warming up.)
The lamp lights and the start up display appears.
CAUTION Ð Do not look into the projection
lens while operating the projector.
Projection on the screen
ON LAMP
ON LAMP
FA N
FA N
(Green) (Green)
Flashing
(Green)(Green) (Green)
(Green)
12
Continued
MENUON/STANDBY INPUT
L-CLICK R-CLICK
ENTERKEYSTONE
AUTO
SET
EXIT
PIPFREEZEMUTE CALL
RESIZE
VOLUME/ADJUST
1
LASER
TEMPLAMP ONBUSYFA NON/STANDBY
KEYSTONESET AUTO AUTOEXIT ENTERMENUINPUT
VOL/ADJ.
TEMP
LAMP ON
BUSYFA N
ON/STANDBY
KEYSTONESET AUTO AUTO
EXIT ENTER
MENUINPUTVOL/ADJ.
1
1
Indicators Remote controlControl panel
(Main unit side)
T
E
M
PL
A
M
PO
NB
U
S
YFA
NO
N
/S
T
A
N
D
B
Y
K
E
Y
S
T
O
N
ES
E
T A
U
T
O A
U
T
OE
X
IT E
N
T
E
RM
E
N
UIN
P
U
TV
O
L
/A
D
J
.
Turn on the connected equipment and put it in
playback mode.Select ÒCancelÓ when the dialog box of Add New Hardware
Wizard screen appears on the computer. 
						

							29
Operations
CONTENTS
Projection on the screen (continued)
Select the input source.Press the INPUT button repeatedly to select it.
The icon of the input source selected appears.(You can select ÒCameraÓ when using the model with a document
imaging camera.)
3
Continued
MENUON/STANDBY INPUT
L-CLICK R-CLICK
ENTERKEYSTONE
AUTO
SET
EXIT
PIPFREEZEMUTE CALL
RESIZE
VOLUME/ADJUST
3
LASER
TEMP
LAMP ON
BUSY FANKEYSTONESET AUTO AUTO
EXIT ENTER
MENUINPUTVOL/ADJ.
3
TEMPLAMP ONBUSY FANON/STANDBY
KEYSTONESET AUTO AUTOEXIT ENTERMENUINPUT
VOL/ADJ.ON/STANDBY
 (Signal sent from the computer)
¥ If you project an image from a computer with an LCD screen while monitoring the image on
the computer, the image may not be projected properly, depending on the computer model.
In this case, turn off the computer display. For details on controlling the computer display, etc.,
refer to the computerÕs manual and description on the software for the computer used.
¥ The projector projects an image by XGA signal (1024 x 768) in full screen.
¥ The projector projects an image by VGA or SVGA signal in full screen size, the image quality
may be slightly degraded. But, when you set the ÒScreen sizeÓ in the menu screen 
54
 to
ÒThruÓ, the display size will be reduced without the image quality be degraded.
¥ The projector has simplified display compatibility with the signals whose picture dots are more
than that of XGA signal. (However, letters and lines can be inequal or a part can be missing.
Some signals may not be projected at all.)
¥ It is recommended to set an external monitor connected to the computer to XGA mode (1024
x 768).
¥ The projector can be also applied to DDC2B (Display Data Channel 2B). If your computer is
applied to the DDC, start up your computer after turning on the projector.
Note
The types of input sources selected when the INPUT button is pressed repeatedly can be
set from the menu screen. 
48
(At shipping from factory, the projector is set so that the RGB signal source input to the
COMPUTER IN 1 connector and the video signal source input to the VIDEO jack can be
selected.)
INPUTINPUT
Remote controlControl panel
(Main unit side)
COMPUTER-1 COMPUTER-2
Video S-video Memory card Camera 
						

							30
Operations
CONTENTS
Adjust the picture size by turning the
zooming lever.Turn to the right to enlarge the picture.
Turn to the left to reduce the picture.
Notes
¥ When changing the projecting angle, adjust the foot adjuster. 
20
¥ When the screen image is distorted in keystone, press the AUTO KEYSTONE button. 
33
¥ The projector may stop operating if the surrounding temperature is too high or if the air filter is
clogged with dust. 
82
¥ Due to the lamp characteristic, flickers may occasionally occur in a picture. This is not
malfunction of the unit.
¥ The projectorÕs liquid crystal panel is made using extremely advanced technology, but there
may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the
panel. Please note that these are not malfunctions.
¥ When trying to press the button whose operation is not available, the icon 
 appears.
¥ When supplying the signal not compatible to the projector, the icon 
 appears.
¥ When signals are not input from the input source, the icon 
 appears.
Projection on the screen (continued)
Focus on the picture by turning the
focusing ring.A still picture is recommended for focusing.
45
LASER
6
MENUON/STANDBY INPUT
L-CLICK R-CLICK
ENTERKEYSTONE
AUTO
SET
EXIT
PIPFREEZEMUTE CALL
RESIZE
VOLUME/ADJUST
TEMPLAMPONBUSY
FA NSTANDBYON/
KEYSTONESET AUTO AUTO
EXIT ENTER
MENUINPUT
VOL/ADJ.
USB MONITOR OUT
COMPUTER IN 1(
Y/PB/PR )COMPUTER IN 2
CONTROLS-VIDEO VIDEOVIDEO INR - AUDIO - LAUDIO
IN AUDIO
OUT
4
5
6
TEMP
LAMP ON
BUSY FANKEYSTONESET AUTO AUTO
EXIT ENTER
MENUINPUTVOL/ADJ.ON/STANDBY
Press VOL/ADJ (+/
-) to adjust volume.
Press the (+) button to increase volume.
Press the (
-) button to decrease volume.
The volume adjusting bar and the icon appear.
6
Remote controlControl panel
(Main unit side)
60