Home > Toshiba > Projector > Toshiba Projector Tlp Wx2200 User Manual

Toshiba Projector Tlp Wx2200 User Manual

Here you can view all the pages of manual Toshiba Projector Tlp Wx2200 User Manual. The Toshiba manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 21

41
Operations
40
■The default setting menuThis menu shows placement status and other settings.Default setting 1 menu
Description
Item
Set the time to wait for the power to be turned off after the last 
operation is made with no input signal. 
Set whether the input with signals is only selected or not. 
Beep when operation is made.
Sets whether to turn on the power when the  ON/STANDBY button is 
pressed (Manual), or when the power cord is plugged in (Auto).  
Sets the lamp power....

Page 22

43
Operations
42
Using the menus (Continued)
[Key lock]Protect from operating errors by locking on the control panel buttons of the
projector. (The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly
operation with the control panel buttons is disabled.
•To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing
the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to
[Off]. (When...

Page 23

45
Maintenance
44
1
Unplug power cord.
2
Wait until lamp is sufficiently cooled.Wait for at least 1 hour.
3
Remove the lamp cover.Loosen the two screws, raise the lamp cover
with your fingers as shown to remove the lamp
cover. Use care to avoid any damage to nails
and/or tip of your finger(s). If you have any
difficulty in removal, you can use a screwdriver
or any other smaller tool for your convenience.
4
Pull out the lamp.Loosen the three lamp locking screws, pull up the
handle, and remove the lamp....

Page 24

47
Maintenance
46
Air filter cleaningThe air filter prevents dust and debris from getting inside the projector. Never run the
projector with the filter removed. It is recommended that the air filter is cleaned regularly.
•The message “Check the air filter for dirt.” is displayed every 100 hours. (If the usage time
exceeds 100 hours, this message is displayed for about 30 seconds when the image is
displayed for the first time after power is turned on. This display will be dismissed with any
operation.)...

Page 25

48
49
Others
The indicator lights to inform you of internal abnormalities.
No power
⇒Problem with projector
•Unplug the power cord, and contact your dealer.Lamp went out during use, or won’t come on⇒Lamp temperature is high so that it is difficult to turn on, the lifetime of the
lamp has ended or the projector is malfunctioning.
•Unplug the power cord and wait for a short while, then turn the power
back on.
•If a lamp burns out, replace it with a new one.
❈The abnormal display will not disappear until...

Page 26

51
Others
50
Specifications■List of general specifications
Item Specification
Consumption Power 300 WWeight 2.8 kg
External Dimensions 288 × 92  × 247 mm (W  × H  × D)(including protruding parts)Cabinet material PC resin and PC+ABS resinConditions for usage
 environment
Temp: 5 °C to 35 °C; relative humidity: 30% to 70%
Display method 3-panel transmission
LCD Panel
P anel size
0.56 type
Drive system
TFT active matrix
Picture elements
1,024,000 pixels (1280H  × 800V)
Lens Zoom lens      F=1.6-1.88...

Page 27

53
Others
52
Specifications (Continued)
■List of supported signals (Y/P
B/P
R signals)
Signal format fh(kHz) fv(Hz)
480i(525i)@60Hz 15.73 59.94
480p(525p)@60Hz 31.47 59.94
576i(625i)@50Hz 15.63 50.00
576p(625p)@50Hz 31.25 50.00
720p(750p)@60Hz 45.00 60.00
720p(750p)@50Hz 37.50 50.00
1080i(1125i)@60Hz 33.75 60.00
1080i(1125i)@50Hz 28.13 50.00
■List of supported signals (Video, S-Video signals)
Video mode fh(kHz) fv(Hz) fsc(MHz)
NTSC 15.73 60 3.58PA L 15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41 P AL-M 15.73...

Page 28

54
■CONTROL terminal●Pin assignment
7
6
8
5
43
21
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
GND Pin No.
1
2
3
4
5
6
7
8Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
Signal ground
Mini DIN 8 pin connector
●Interface format
1Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:  1 bit
2Communication format STX (02h)  Command (3Byte)  ETX (03h)
Only 1 command valid per communication.
3Data format For input...

Page 29


				            
Start reading Toshiba Projector Tlp Wx2200 User Manual

Related Manuals for Toshiba Projector Tlp Wx2200 User Manual

All Toshiba manuals