Toshiba Projector Tlp 561 User Manual

21
Installation and
connections
CONTENTSProjector placement angle adjustment (Foot adjuster)
Foot adjuster
release buttonFoot adjuster The tilt of the projector can be adjusted using the foot adjuster.  Adjust this when the highest position by the lens shift dial 
20 is
insufficient.  Refer to “Projection on the screen” 
28, and adjust the foot adjuster after projecting a picture.
Lift the front of the projector until the desired tilt
angle is obtained and hold down the foot adjuster
release button.
The...

22
Installation and
connections
CONTENTS
Ceiling-mounted front projection
Viewing a picture projected on the front of the screen from a
ceiling installation.
Ceiling-mounted rear projection
Viewing a picture projected through the back of the screen from a
ceiling installation.
Perform the “Projection mode” setting on the menu screen for the projection method. 51
Note
The relation between the projection size and the distance to the screen is the same as that of the floor-mounted projection mode 18....

23
Installation and
connections
CONTENTS
Notes
•The projector cannot be connected to a computer without an analog RGB connector. For details, refer to the computer manual.
•You may not be able to connect some computers to the projector. For details, consult the dealer.
•When connecting to a Macintosh computer, some models may need a Mac adapter for connection.
•Some computers may have output modes which are not compatible with this projector. Check the compatibility of the connectors, signal levels,...

24
Installation and
connections
CONTENTSConnecting video equipment
Note
The S-VIDEO IN connector and VIDEO IN jack can be used independently, but the audio input jack is used for all input sources.
You can project the picture from video equipment.
Check that the power supplies for the projector and for the video equipment are off before connecting the cables.
Pin plug (red)
To audio output (R)
(Yellow) To VIDEO IN jackTo S-VIDEO IN connector
Be sure to connect in the proper 
direction.To S-video output...

25
Installation and
connections
CONTENTSConnecting video equipment (continued)
You can project the picture from video equipment with component video output jack.
Check that the power supplies for the projector and for the video equipment are off before connecting the cables.
COMPUTER IN connector
For use as both analog RGB and Y/P
B/PR input. At shipping from factory, it is 
set for use as analog RGB input.
Change the setting on the menu screen when using as Y/P
B/PR input. 
AUDIO IN jack
For use as...

26
Installation and
connections
CONTENTSProjector operation control by a computer
CONTROL connector
Computer
To RS-232C port Control cable (supplied) To CONTROL connector
Be sure to connect in the proper 
direction.USB AUDIO INCONTROLS-VIDEO IN VIDEO INCOMPUTER OUT (
Y/PB/PR )COMPUTER IN (
Y/PB/PR )
You can control the projector by a computer connected with the control cable supplied. 72
Check that the power supplies for the projector and for the computer are off before connecting the cables.
Note
Do not...

27
Installation and
connections
CONTENTSHow to use the output connector
You can output analog RGB signal to a computer monitor, etc.
Check that the power supplies for the projector and for the computer are off before connecting the cables.
Notes
• The analog RGB signals or Y/PB/PR signals of the COMPUTER IN connector are output from the COMPUTER OUT connector.
• Signals are output from the COMPUTER OUT connector even when in the standby mode.
• A general computer monitor may not display a normal picture...

28
Operations
CONTENTS
Preparation
1Install and connect the projector properly.
2Take off the lens cover.
Press ON/STANDBY.
The projector turns on and the ON, LAMP and FAN indicators
light in green.
(The LAMP indicator blinks while the lamp is warming up.)
The lamp lights and the start up display appears.
CAUTION – Do not look into the projection
lens while operating the projector.
Projection on the screen
ON / STANDBY
FANTEMPLAMPON
ON / STANDBY
FANTEMPLAMPON
(Green) (Green) (Green) (Green)...

29
Operations
CONTENTSProjection on the screen (continued)
Press ENTER to confirm.
Press EXIT to return to step 2 if you want to re-select a
language.3
Continued
MENU
ON /INPUT
ENTERCT-90106
KEYSTONE AUTO SET
EXIT /
P.MODE
PIP FREEZE
MUTE
CALLRESIZE
VOL / ADJ
STANDBY
KEYSTONE
AUTOSET
EXIT
ON / STANDBY
VOL / ADJ
ENTER
MENU
INPUT
FANTEMPLAMPON
2
2,3
2 2,3
ENTER
ENTER
Remote control
Control panel
(Main unit side)Select a desired language with the
selection buttons (
  /  ), and
press ENTER.
A menu...

30
Operations
CONTENTS
Select the input source by pressing INPUT
repeatedly.
At shipping from factory, “Analog RGB” connected to
COMPUTER IN connector or “Video” connected to VIDEO IN
Jack can be selected. (You can select “Camera” when using the
model with a document imaging camera.)
The icon and the name of the selected input source appear on
the screen.
Projection on the screen (continued)
5-a
5-b
MENU
ON /INPUT
ENTER
CT-90106
KEYSTONE AUTO SET
EXIT /
P.MODE
PIP FREEZE
MUTE
CALLRESIZE
VOL / ADJ...