Toshiba Projector Tdp S9 User Manual

21
Operations
Operations
■ Connecting the power cord
1Insert the power cord connector into the
AC  IN socket of the projector.
2Insert the power cord plug into a wall or
other power outlet.
■ Turning the power on
1Turn on the main power switch
The ON indicator will change to green
flashing, indicating standby mode.
2Press the I/ ON/STANDBY button.
The power turns on, and the following
2 green indicators light: ON and
LAMP. After a moment, the start-up
screen appears.
Start-up screen
Control panel...

22
Note
•The start-up screen will disappear after a moment.
■ T urning the power off
1Press the I/ ON/STANDBY button.
A  message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer val\
id after the
message disappears.)
2Press the I/ ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp...

23
Operations
4Use the  or  button to select the desired
language and press the control panels MENU
b utton or the remote controls Enter button.
Message for setup confirmation is displayed in a selected
language.
3Activate the connected device.
Turn on and start the connected device such as a computer.
4Press the control panels SOURCE button or the remote
controls Source button.
An image of the connected equipment is projected.
Each time you press the control panel’s SOURCE button or the remote...

24
5Projector placement angle adjustments
The placement angle and the height of the projected image can be adjuste\
d by the foot
adjuster.
1Lift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
2To  adjust the horizontal angle, use the
tilt adjuster.
To  s tow the foot adjuster, hold up the projector while
pressing the foot adjuster release button, then slowly
lower the projector....

25
Operations
■Manually selects an input source (Source)
If you are connecting multiple sources to the projector
simultaneously, press the control panel’s SOURCE button
or the remote control’s Source button. The projector will
detect your source.
Note
•The image may not be projected or auto adjustment/setting may not be per\
formed correctly for
input signals other than those supported by the projector 
p.40, p.41.
■ Correcting the keystone distortion (Keystone)
When the foot adjuster p.24 is used to...

26
■Automatically adjusts frequency and phase (Auto)
If source is a computer, press the control panel’s
AUTO button or the remote control’s Auto button to
adjusts frequency and phase.
■ Switching the image aspect ratio (4:3/16:9)
Toggle the remote control’s 4:3/16:9 button to
change the aspect ratio.
Note
•T he aspect ratio can also be set via the Image menu p.28.
■Cutting off the sound temporarily (Mute)
Press the remote controls Mute button.
The sound is cut off. (The Mute function is released when...

27
Operations
You can call up on-screen menus, and conduct a number of adjustments and \
settings
using the operation buttons 
p.16 on the control panel (main unit side) and remote control.
■ How to use the menus
The menu shown below is for operation instructions purposes and might di\
ffer from the
actual display.
Using the menus
Note
•Menu adjustments and settings are saved when the power is turned off via the  I/ ON/STANDBY
button. If the power cable is disconnected before this, or the power goe\
s...

28
Item   Description
Contrast Adjust the image contrast.
Lower   Higher
Brightness Adjust the brightness of the image.
Darker   Brighter
Ke ystone Adjusts image distortion caused by tilting the projector.
Reduce the upper width   Reduce the lower width
Aspect Ratio Selects this function to fit 16:9, 4:3 aspect ratio. If the input signal\
 is a
computer signal greater than SVGA or component 1080i / 720p, 16:9
or 4:3 aspect ratio will be available.
16:9   4:3
Blank Screen Blanks the screen temporarily,...

29
Operations
■Video menu
Use this menu to adjust video-related items. When using a video source, \
the on-screen
display allows changes to the "Video" menu.
Item   Description
Saturation Adjusts a video image from black and white to fully saturated
color.
Weaker   Stronger
Tint Adjust the tint of the image color.
Greenish   Reddish
Sharpness Adjust the sharpness of the image.
Softer   Sharper 

30
■Display menu
Use this menu to adjust display-related items. When using a computer, th\
e on-screen
display allows changes to the "Display" menu.
Item   Description
Phase Synchronizes the signal timing of the display with that of the
graphic card. If you experience an unstable or flickering image,
use the phase function to correct it.
Switch with  and  to adjust the setting.
T racking Changes the display data frequency to match the frequency of
your computer graphic card. If you experience a...