Toshiba Projector Tdp S9 User Manual

							
Others
Maintenance
Operations
Preparations
Before Using
OWNER’S MANUAL
DATA PROJECTOR
TDP-S9(SVGA) 
						

							
2
The lightning flash with arrowhead symbol, within an equilateral triangl\
e, is intended
to alert the user to the presence of uninsulated "dangerous voltage" wit\
hin the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to aler\
t the user to the
presence of important operating and maintenance (servicing) instructio\
ns in the
literature accompanying the appliance.
FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject\
 to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device mu\
st accept any
interference received, including interference that may cause undesired o\
peration.
This equipment has been tested and found to comply with the limits for a\
 Class B digital
device, pursuant to part 15 of the FCC Rules.  These limits are designed to provide reasonable
protection against harmful interference in a residential installation.  \
This equipment generates,
uses and can radiate radio frequency energy and, if not installed and us\
ed in accordance with
the instructions, may cause harmful interference to radio communications\
.
However, there is no guarantee that interference will not occur in a par\
ticular installation.
If this equipment does cause harmful interference to radio or television\
 reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: W ARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
W ARNING: Handling the cord on this product or cords associated with accessories s\
old with
this product, will expose you to lead, a chemical known to the State of \
California
to cause birth defects or other reproductive harm. 
Wash hands after handling.
W ARNING: This [product] contains mercury. Disposal of mercury may be regulated du\
e to
environmental considerations. For disposal or recycling information, ple\
ase contact
your local authorities or the Electronic Industries Alliance: www.eiae.org.
USA only
MODEL NAME: TDP-S9
TRADE NAME: DATA PROJECTOR               MODEL NAME: TDP-S9
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
USA only
SAFETY PRECAUTIONS
Before Using
USA only 
						

							
Before Using
3
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.
- Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC. 9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A
Phone: (949) 583-3000
W ARNING: Changes or modifications made to this equipment, not expressly approved
by Toshiba, or parties authorized by Toshiba, could void the user’s authority
to operate the equipment.
Notice: This Class B digital apparatus complies with Canadian ICES-003.  Cet app\
areil
numérique de la classe B est conforme à la norme NMB-003 du Canada\
.
CANADA only
USA only 
						

							
4
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNERS MANUAL AND THOSE
MARKED ON THE UNIT.  RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This set has been designed and manufactured to assure personal safety.  \
Improper use can
result in electric shock or fire hazard.  The safeguards incorporated in this unit will protect you
if you observe the following procedures for installation, use and servic\
ing.  This unit is fully
transistorized and does not contain any parts that can be repaired by th\
e user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE.  REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.
1. Read Owners Manual
After unpacking this product, read the
owner's manual carefully, and follow
all the operating and other
instructions.
2. Power Sources
This product should be operated only
from the type of power source
indicated on the marking label.
If you are not sure of the type of power
supply to your home, consult your
product dealer or local power
company.
For products intended to operate from
battery power, or other sources, refer
to the operating instructions.
3. Source of Light
Do not look into the lens while the
lamp is on.  The strong light from the
lamp may cause damage to your eyes
or sight.
4. Ventilation
Openings in the cabinet are provided
for ventilation and to ensure reliable
operation of the product and to protect
it from overheating, and these
openings must not be blocked or
covered.
The openings should never be
blocked by placing the product on a
bed, sofa, rug or other similar surface.
This product should not be placed in a
built-in installation such as a bookcase
or rack unless proper ventilation is
provided or the manufacturer's
instructions have been adhered to. 
						

							
Before Using
5
5. Heat
The product should be situated away
from heat sources such as radiators,
heat registers, stoves, or other
products (including amplifiers) that
produce heat.
6. Water and Moisture
Do not use this product near water.- for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming
pool and the like.
7. Cleaning
Unplug this product from the wall
outlet before cleaning.  Do not use
liquid cleaners or aerosol cleaners.
Use a soft cloth for cleaning.
8. Power-Cord Protection
Power-supply cords should be routed
so that they are not likely to be walked
on or pinched by items placed upon or
against them, paying particular
attention to cords at plugs,
convenience receptacles, and the
point where they exit from the product.
9. Overloading
Do not overload wall outlets; extension
cords, or integral convenience
receptacles as this can result in a risk
of fire or electric shock. 
						

							
6
IMPORTANT SAFETY INSTRUCTIONS  (Continued)
10. Lightning storms
For added protection for this product
during storm, or when it is left
unattended and unused for long
periods of time, unplug it from the wall
outlet.  This will prevent damage to the
product due to lightning and power-
line surges.
However, while it is thundering or
lightning, do not touch the apparatus
and any connected cable and/or
equipment.
This will prevent you from receiving
the electric shock by an electric surge.
11. Object and Liquid Entry
Never push objects of any kind into
this product through openings as they
may touch dangerous voltage points
or short-out parts that could result in a
fire or electric shock.  Never spill liquid
of any kind on the product.
12. Do not place the productvertically
Do not use the product in the upright
position to project the pictures at the
ceiling, or any other vertical positions.
It may fall down and dangerous.
13. Stack Inhibited
Do not stack other equipment on this
product or do not place this product on
the other equipment.  Top and bottom
plates of this product develops heat
and may give some undesirable
damage to other unit.
14. Attachments
Do not use attachments not
recommended by the product
manufacturer as they may cause
hazards. 
						

							
Before Using
7
15. Accessories
Do not place this product on an
unstable cart, stand, tripod, bracket, or
table.  The product may fall, causing
serious injury to a child or adult, and
serious damage to the product.  A
product and cart combination should
be moved with care.  Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
S3125A
16. Damage Requiring Service
Unplug this product from the wall
outlet and refer servicing to qualified
service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to
rain or water.
d) If the product does not operate normally by following the operating
instructions.  Adjust only those
controls that are covered by the
operating instructions as an improper
adjustment of other controls may
result in damage and will often require
extensive work by a qualified
technician to restore the product to its
normal operation. e) If the product has been dropped or
damaged in any way.
f) When the product exhibits a distinct
change in performance - this indicates
a need for service.
17. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
This product incorporates glass
components, including a lens and a
lamp.  If such parts should break,
please handle with care to avoid injury
and contact your dealer for repair
service.  The broken pieces of glass
may cause to injury.  In the unlikely
event of the lamp rupturing, thoroughly
clean the area around the projector
and discard any edible items placed in
that area.
18. Servicing
Do not attempt to service this product
yourself as opening or removing
covers may expose you to dangerous
voltage or other hazards.  Refer all
servicing to qualified service
personnel. 
						

							
8
19. Replacement Parts
When replacement parts are required,
be sure the service technician has
used replacement parts specified by
the manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result
in fire, electric shock, or other
hazards.
(Replacement of the lamp only should
be made by users.)
20. Safety Check
Upon completion of any service or
repairs to this product, ask the service
technician to perform safety checks to
determine that the product is in proper
operating condition.
21. Do not leave thermal-paper
documents or easily
deformed items on top of the
unit or near the air exhaust
for long periods of time.
The heat from the unit could erase the
information on the thermal paper, or
cause deformation or warping.
22. Do not use the product in a
closed installation state.
Do not place the product in a box or in
any other closed installation state.
Otherwise it may overheat. This could
result in a risk of fire.
IMPORTANT SAFETY INSTRUCTIONS  (Continued) 
						

							
Before Using
9
If your line voltage is 220 to 240V, use one of the following types of c\
able.
Plug
configurationPlug type
Australian
240V
10A
North American240V
15A Switzerland
240V
6A
Line voltage
EURO
UK 220 – 240V
220 – 240V 200 – 240V
200 – 240V 200 – 240V
Plug
configuration
Plug type Line voltage
Use a 5A fuse which is approved by ASTA 
or BSI to BSI362.
Always replace the fuse cover after 
changing the fuse.
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if\
 you ever have to ship your
projector. For maximum protection, repack the set as it was originally p\
acked at the factory.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location\
 to a warm location. When the
unit is exposed to such a change in temperature, moisture may condense o\
n the crucial internal
parts. To prevent the unit from possible damage, do not use the unit for at leas\
t 2 hours when there is
an extreme or sudden change in temperature
.
Place and Manner of Installation
•
Do not place in hot locations, such as near heating equipment.  Doing so\
 could cause malfunction,
and shorten the life of the projector.
• Avoid locations with oil or cigarette smoke.  Doing so will dirty the opt\
ical parts, shortening their
lives, and darkening the screen.
• Do not use the product vertically in any upright position or slantwise i\
n an angle of 20 degrees or
more.
• Using this instrument near a TV or radio may cause interference to the images or audio sound. If this\
happens, move it away from the TV or radio.
• Moving the projector from a low-temperature room to a high-temperature r\
oom may cause
condensation on the lens or internal parts in the instrument. If you con\
tinue to use it in that situation,
the malfunction may result. Ensure to wait until the condensation natura\
lly disappears.
• In a high altitude location where air is thin, cooling efficiency is red\
uced so use it with the ambient
temperature being lowered.
POWER SUPPLY CORD SELECTION 
						

							
10
EXEMPTION CLAUSES
•Toshiba Corporation bears no responsibility in the case of damages arisin\
g from natural disaster
such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, operation, theft or
mischief by third parties, other accidents, or use under abnormal condit\
ions including erroneous or
improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost\
 profit, work interruption,
corruption or loss of the memory contents, etc.) arising from the use o\
f or the inability to use this
unit.
• Toshiba Corporation accepts no liability whatsoever for any damages arisi\
ng from not having
followed the descriptions in this Instruction Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arisi\
ng from malfunctions
arising from combination with equipment or software that is not related \
to Toshiba Corporation.
IMPORTANT PRECAUTIONS  (Continued)
Av oid Volatile  Liquid
Do not use volatile liquids, such as an insect spray, near the unit.  Do\
 not leave rubber or plastic
products touching the unit for a long time.  They will leave marks on the finish.
If cleaning with a chemically saturated cloth, be sure to follow the pro\
duct's precautions.
In the spaces provided below, record the Model and Serial No. located at\
 the bottom of your
projector.
Model No. Serial No.
Retain this information for future reference.