Toshiba D-rw2 Manual
Have a look at the manual Toshiba D-rw2 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
141 Function Setup Recording Playback Editing Introduction Connections Basic Setup Function Setup Others EN Settings for Progressive Scan Mode This unit is compatible with the Progressive Scan System. The feature provides you with the higher defi nition images than the traditional output system does. To utilize this feature, you must set Progressive Scan mode to “ON” in the Setup menu by following the steps below. 1 Press [SETUP]. 2 Using [K / L], select “Playback”. Press [ENTER]. Playback menu will appear. . 3 Using [K / L], select “Video”. Press [ENTER]. (Continued) Start VODUJPOTFUVQ@6%JOEEVODUJPOTFUVQ@6%JOEE
142 Function Setup EN 4 Using [K / L], select “Progressive”. Press [ENTER]. 5 Using [K / L], select “ON”. Press [ENTER]. Confirmation window will appear. 6 Using [{ / B], select “Yes”. Press [ENTER]. Final confirmation window will appear. • If your TV does not support progressive scan, distorted picture or blank screen will appear when “Yes” option is selected. In this case, just wait for 15 seconds for auto recovery. ON Video - Progressive OFF Video - Progressive Activating progressive scan: Check your TV has progressive scan and connect with component video cable. NOTE: If there is no picture or picture is distorted after selecting “Yes”, Wait about 15 seconds for auto recovery. Activate?No Ye s Video OFF Auto Progressive Still Mode VODUJPOTFUVQ@6%JOEEVODUJPOTFUVQ@6%JOEE
143 Recording Playback Editing Introduction Connections Basic Setup Function Setup Others EN 7 Using [K / L], select “Yes”. Press [ENTER] within 15 seconds. Your setting will be activated. 8 Press [SETUP] to exit. Video - Progressive Confirm again to use progressive scan. If Picture is good, Select “Yes”. No Ye s Notes • If your TV is compatible with Progressive Scan (525p / 480p), you must use the Component Video cable (commercially available) to connect this unit to the TV. (See Method 2 on page 25.) Make sure the “P.SCAN” appears on the front panel display. If not, use the video cable and set the Progressive Scan mode to “OFF”, or press and hold [SETUP] for more than 3 seconds during DVD playback, so that the “P.SCAN” on the front panel display disappears. • If there is no picture or picture is distorted after selecting “Yes” in step 6, wait about 15 seconds. It will go back to Video- Progressive menu automatically. VODUJPOTFUVQ@6%JOEEVODUJPOTFUVQ@6%JOEE
144 Function Setup EN Settings for Still Mode Press [STOP C] if you are playing a disc. Set the type of still image in pausing mode. 1 Follow steps 1 to 3 on page 141 to display the Video setting menu. 2 Using [K / L], select “Still Mode”. Press [ENTER]. 3 Using [K / L], select a setting. Press [ENTER]. Your setting will be activated. Auto : Optimun setting is selected. Field : Flicker-free images are played back in pause playback mode. Frame : Higher- resolution images are played back in pause playback mode. 4 Press [SETUP] to exit. Video OFF ProgressiveStill Mode Auto Video-Still Mode Auto Field Frame Note • Frame is one complete video image and made up of 2 fields (There are 30 frame per second of NTSC video). Start VODUJPOTFUVQ@6%JOEEVODUJPOTFUVQ@6%JOEE
Others ● Troubleshooting ● Language code ● Glossary ● Specifications 0UIFST@6%JOEE0UIFST@6%JOEE
146 Others EN Troubleshooting Before requesting service for this unit, check below for a possible caus\ e of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the probl\ em and restore proper operation. Power ■ The power does not turn on. • Check that the AC power cord is connected securely. • (In case of power failure) Check the breaker. Picture ■ There is no picture. • Re-connect the connecting cords securely. • Check if the connecting cords are damaged. • If Setup menu appears on the TV screen, press [RETURN] to exit the menu. • Check the connection to your TV (page 24). • Check if the Interlace/Progressive mode is set correctly according to your TV (pages 141-143). • Switch the input selector on your TV (such as to “LINE1”) so that the signal from the unit appears on the TV screen. ■ Picture noise appears. • The disc is dirty or flawed. • If the video signal is sent to your TV through a VCR or if your TV is equipped with a VCR, the copy- protection signal applied to some DVD programs could affect picture quality. If you still experience this problem even when you connect the unit directly to your TV, try connecting the unit to your TV’s S-VIDEO input. ■ TV program reception does not fill the screen. • Try to set the channels with “Auto Preset” in the Setup menu (pages 32-33). • Select a channel of any TV program using [CH / ]. ■ TV program pictures are distorted. • Adjust TV antenna. • Adjust the picture (see the TV’s instruction manual). • Place the unit and TV farther apart. • Place the TV and any bunched antenna cables farther apart. ■ TV channels cannot be changed. • Switch the input to TV. • Connect the antenna cable correctly (page 24). ■ Playback picture is distorted • Keep the equipment which may cause electrical disturbances, such as a mobile phone, away. Sound ■ There is no sound. • The disc is dirty or flawed. • Re-connect all connections securely. • Check if the connecting cord is damaged. • Check the connections to the amplifier input. • The input source setting on the amplifier is incorrect. • The recorder is in pause mode or in Slow forward / Slow reverse play. • The recorder is in fast forward or fast reverse mode. • If the audio signal does not come through the DIGITAL OUT (COAXIAL) jack, check the Audio settings (pages 135-137). ■ No DTS sound on digital output. • Change the setting menu for DTS to ON. ■ No DTS sound from analog output. • This unit has no analog sound output when playing the selected DTS sound mode. ■ Sound is noisy. • The disc is dirty or flawed. Remote control ■ The remote control does not work. • Check the antenna or cable connection to the main unit. • Check the battery life of the remote control. • Check if there is an obstacle between the sensor and the remote control. 0UI FST @ 6 %J O EE 0UIFST@6%JOEE
147 Recording Playback Editing Introduction Connections Basic Setup Function Setup Others EN Playback ■ The disc does not play. • No disc is inserted. • A blank disc is inserted. • The disc is upside down. Insert the disc with the labeled side facing up. • The disc is not correctly inserted. • The unit cannot play certain discs (such as a CD- ROM) (pages 9-10). • The region code on the DVD-Video does not match the unit (page 10). • Moisture has condensed inside the unit. Remove the disc and leave the unit turned on for about two hours until the moisture evaporates (page 4). • If the disc was recorded on another recorder, the unit cannot play the disc if it was not finalized (page 51). ■ Playback image freezes for a second. • During the playback of two layered disc, picture may freeze for a moment when the 1st layer switches to the 2nd layer. This is not a malfunction. ■ The disc does not start playback from the beginning. • Resume play was activated (page 87). Press [STOP C] twice. • You have inserted a disc whose Title menu or DVD menu automatically appears on the TV screen when it is first insert. ■ The unit starts playing from the disc automatically. • The DVD-Video features an auto playback function. ■ Some functions such as Stop, Search, Fast / Slow reverse or Fast / Slow forward cannot be performed. • Depending on the disc, you may not be able to do some of the operations above. See the instruction manual supplied with the disc. ■ The language for the sound track cannot be changed. • Multilingual tracks are not recorded on the DVD- Video, DVD-R or DVD-RW being played. • The DVD-Video prohibits the changing of the language for the sound track. • Try changing the language using the DVD-Video’s menu. ■ The subtitle language cannot be changed or turned off. • Multilingual subtitle are not recorded on the DVD- Video. • The DVD-Video prohibits changing of the subtitles. • Try changing the subtitle using the DVD-Video’s menu. ■ The angles cannot be changed. • Multi-angles are not recorded on the DVD-Video being played. • The angle-change operation is whenever possible as long as the disc contains a multi-angle portion. Actual change will be performed when the portion has come up. • The DVD-Video prohibits changing angles. • Try changing the angle using the DVD-Video’s menu. Recording/Timer Recording/Editing ■ The channel cannot be changed from the channel you are recording. • Set the TV’s input to “TV”. ■ Recording does not start immediately after you press [REC I]. • A new DVD-R or DVD-RW has been inserted. It takes a while for the unit to automatically format a DVD-RW. ■ Nothing was recorded even though you set the timer setting correctly. • There was a power failure during recording. • The unit’s internal clock stopped due to a power failure that lasted for more than 30 seconds. Reset the clock (pages 38-43). • Disconnect the AC power cord from the AC outlet, and connect it again. • The program contains copy protection signals that restricts copying. • The timer setting overlapped with another setting that has priority. ■ Recording does not stop immediately after you press [STOP C]. • It will take a few seconds for the unit to input disc data before recording can stop. ■ Timer Recording is not complete or did not start from the beginning. • The timer setting overlapped with another setting that has priority (page 67). • Disc space was not enough. 0UIFST@6%JOEE0UIFST@6%JOEE
148 Others EN Troubleshooting (cont’d) Others Error message Error message Cause SolutionDisc Error --- Please eject the disc. --- Playback feature may not be available on this Disc. • Unplayable disc is inserted in the unit. • The disc is upside down. • Insert the standardized disc which bear the marks on pages 9-10. • Insert the disc with the labeled side facing up. Region Error --- Please eject the disc. --- Playback is not authorized in your region. • Playback is not authorized in the region of the DVD-Video disc which you inserted in the unit. • Insert the DVD-Video disc with region codes 1 or ALL. Parental Lock On The current selected parental level prohibits playback. • The current selected parental level in the Setup menu prohibits playback. • Check the “Parental Lock” setting (pages 138-140). Recording Error This program is not allowed to be recorded. • The recording function encountered the copy prohibited program. • You cannot record copy prohibited programs. ■ The unit does not operate properly. ● When static electricity, etc., causes the unit to operate abnormally, unplug the unit and then plug it in again. ■ The disc tray does not open when you press [OPEN/CLOSE A]. ● It may take a few seconds for the disc tray to open after you have recorded or edited a disc. ■ “Repairing” appears on the TV screen. ● If there is a power failure or unplugging during recording, finalizing, formatting or editing (even after “Wait for a moment.” message is disappeared), a Repairing process will begin automatically just after turning the unit on again. It may take several minutes up to about four hours. ■ In a case you intend to cancel the Repairing process. ● If you intend to cancel the Repairing process, press [A OPEN/CLOSE ] on the front panel, then select “Yes” with [ { / B ] and press [ENTER]. After that, the disc tray will automatically open. In case the Repairing process is canceled, the disc MAY NOT work. Repairing Repairing Do you want to cancel a repairing process ? When selecting “Yes”, the disc may not be usable. Yes No 0 UI FST @ 6 %J O EE 0UIFST@6%JOEE
149 Recording Playback Editing Introduction Connections Basic Setup Function Setup Others EN Error message Cause Solution Recording Error This program is not recordable in Video mode.• You are trying to record the copy- once program onto the DVD-RW disc in Video mode.• Set “Format mode” to “VR mode” (pages 52-54). Recording Error Cannot record on this disc.• You are trying to record onto the disc which is unrecordable, or whose status is unable to record. • The disc is dirty. • The disc is damaged.• Insert the recordable disc, and ensure the disc status satisfies the recording requirements (page 9). • Clean the disc with a cleaning cloth. • Replace the disc. Recording Error This program is not allowed to be recorded on this disc.• You are trying to record the copy- once program onto the DVD-RW disc which is not compatible with CPRM.• Insert the DVD-RW disc in VR mode (ver.1.1 or 1.2 compatible with CPRM). Recording Error This disc is protected and not recordable.• You are trying to record on to the protected disc which is set in the Disc menu.• Release the disc protect setting in the Disc menu (page 72). Recording Error Disc is full. (No area for new recording)• You are trying to record onto the disc which has no space for recording.• Insert the recordable disc with enough recording space. Recording Error You cannot record more than 99 titles on one disc. (The maximum is 99)• You are trying to record onto the disc on which the number of recording titles exceed the maximum (99). • Delete unnecessary titles (page 100). Recording Error You cannot record more than 999 chapters on one disc. (The maximum is 999)• You are trying to record onto the VR mode DVD-RW disc on which the number of recording chapters exceed the maximum (999).• Delete unnecessary chapter marks (page 106). Recording Error You cannot record on this disc as Control Information is full.• This disc has no space to write the Control Information when recording or deleting contents. When editing has been repeatedly performed, the control Information area may come up to be full even the recording area has enough space.• Delete unnecessary titles (page 100). 0UIFST@6%JOEE0UIFST@6%JOEE
150 Others EN Troubleshooting (cont’d) Error message Cause Solution Recording Error You cannot record on this disc as Power Calibration Area is full.• When recordings are performed repeatedly onto an unstable disc, this area may come up to be full. Every time you insert a disc for recording, the disc’s working area will be taken up. And if you repeat this frequently, it will be used up sooner and you may not be able to record full 99 titles.• Insert a new disc. Recording Error This disc is already finalized.• You are trying to record onto the disc already finalized.• Release the finalizing for this disc (page 75). * If you are still having trouble with the unit after checking “Troubleshooting”, write down the error code and the error description before calling the TACP’s Consumer Solution Center or, for Canada, TCL customer support line mentioned on pages 155 and 156. Frequently Asked Questions ■ Can I record to CD-R/RW? No, this unit records only DVDs. ■ Can I play DVD-Video that is bought in another country? Possible when the region code of the disc is 1 and All. ■ Can I connect the unit to my PC? No, you cannot control the unit by PCs. 0UIFST@6%JOEE0UIFST@6%JOEE