Toshiba D-rw2 Manual

							131
Recording
Playback
Editing
Introduction
Connections
Basic Setup
Function Setup
Others
EN
4
 Using [K / L], select a desired item. 
Press [ENTER].
Disc Menu Language (Default : English)
Set the language for the Disc Menu.
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
Audio Language (Default : Original)
Set the Audio language.
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
• When Original is selected, the audio language will be in the disc’s 
default language. 
Subtitle Language (Default : OFF)
Set the Subtitle language.
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
(Continued)
Language
Audio Original  Disc Menu English
Subtitle OFF
Language - Disc Menu 
French
Spanish
Other English
Language
Audio Original  Disc Menu English
Subtitle OFF
Language - Audio
English
French
Spanish
Other Original
Language
Audio Original  Disc Menu English
Subtitle OFF
Language - Subtitle 
OFF
French
Spanish
Other English
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE








 
						

							132
Function Setup
EN
Language setting (cont’d)
If “Other” is selected, press 4-digit code using the 
Number buttons. Refer to “Language code” on page 151.
• When you finish entering the code, press [ENTER]. 
5
  Press [SETUP] to exit.
Language - Subtitle
Code Input- ---
Notes
•  Only the languages supported by the disc can be selected.
•  Audio Language setting may not be available on some discs.
•  Some DVD-Video discs allow you to change subtitle selections only via the disc menu. If this is the case, press 
[MENU/LIST] and choose the appropriate subtitle language from the selection on the disc menu.
•  Press [CLEAR] or [s] to erase numbers entered incorrectly at step 4.
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE








 
						

							133
Function Setup
Recording
Playback
Editing
Introduction
Connections
Basic Setup
Function Setup
Others
EN
Display setting
 Press [STOP C] if you are playing a disc.
1
 Press [SETUP].
2
 Using [K / L], select “Display”. 
Press [ENTER].
Display menu will appear.
3
 Using [K / L], select a desired item. 
Press [ENTER].
OSD Language (Default : English)
Set the language for OSD.
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
(Continued)
Display
Angle IconON
Screen Saver
FL Dimmer10 minutes
Bright OSD Language EnglishOSD Language
Français
Español English
Start
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE








 
						

							134
Function Setup
EN
Display setting (cont’d)
Angle Icon (Default : ON)
Set to “ON” or “OFF”.
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
Screen Saver (Default : 10 minutes)
Set the time to activate the screen saver function on the screen.
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
FL Dimmer (Default : Bright)
Set the brightness of the front panel display.
You can choose among “Auto”, “Bright” and “Dark”.
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
• If “Auto” is selected, the display is shown brighter when the power is 
on, darker when the power is off.
4
  Press [SETUP] to exit.
Display
Angle IconON
Screen Saver
FL Dimmer10 minutes
Bright OSD Language      EnglishScreen Saver
5 minutes
10 minutes OFF
15 minutes
30 minutes
Display
Angle IconON
Screen Saver
FL Dimmer10 minutes
Bright OSD Language EnglishAngle Icon
OFF ON
Display
Angle IconON
Screen Saver
FL Dimmer10 minutes
Bright OSD Language  EnglishFL Dimmer
Bright
Dark Auto
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE








 
						

							135
Function Setup
Recording
Playback
Editing
Introduction
Connections
Basic Setup
Function Setup
Others
EN
Audio setting
Choose the appropriate Audio settings for your 
equipment.
It will only affect DVD discs during playback.
 Press [STOP C] if you are playing a disc.
1
 Press [SETUP].
2
 Using [K / L], select “Playback”. Press 
[ENTER].
Playback menu will appear.
.
3
 Using [K / L], select “Audio”. Press [ENTER].
Digital Out
Set the digital audio output.
• Using [K / L], select a setting. Press [ENTER].
  Option window will appear. Proceed to step  A ,  B  or  C  on next 
page.
(Continued)
Audio
Dynamic Range Control ONDigital Out
Digital Out
Dolby Digital  Stream PCM 48kHz
DTS OFF
ABC
Start
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE








 
						

							136
Function Setup
EN
Audio setting (cont’d)
ASettings for PCM (Default : 48kHz)
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
48kHz   : If your amplifier/decoder is NOT compatible with 96kHz PCM, 
select“48kHz”. 96kHz sound will be output in 48kHz.
96kHz   : If your amplifier/decoder is compatible with 96kHz PCM, select 
“96kHz”. 96kHz sound will be output.
Note
When playing disc with copyright protection
•  Even if you select “96kHz”, the sound will be down sampled at 48kHz.
B Settings for Dolby Digital (Default : Stream)
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
PCM   : Convert the Dolby Digital into PCM(2 channel).
    When your amplifier/decoder is NOT compatible with Dolby 
Digital, set to “PCM”.
Stream   : Outputs Dolby Digital signals.
    When your amplifier/decoder is compatible with Dolby Digital, 
set to “Stream”.
Note
When playing a DVD-RW disc recorded in VR mode
•  If the audio source on a disc is Dolby Digital format, set “Dolby Digital” to 
“PCM” so that you can switch to main (L), sub audio (R), or a mix of both (L/
R) with your amplifier/decoder.
Digital Out - PCM
96kHz 48kHz
Digital Out - Dolby Digital
Stream PCM
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE








 
						

							137
Recording
Playback
Editing
Introduction
Connections
Basic Setup
Function Setup
Others
EN
C Settings for DTS (Default : OFF)
• Select a setting using [K / L], then press [ENTER].
  Your setting will be activated.
ON   : Outputs DTS signals.
    When your amplifier/decoder is compatible with DTS, set to 
“ON”.
OFF   : No DTS signal is output.
    When your amplifier/decoder is NOT compatible with DTS, set 
to “OFF”.
Dynamic Range Control (Default : ON)
Set to “ON” to compress the range between soft and loud sounds.
• Using [K / L], select a setting. Press [ENTER].
  Your setting will be activated.
4
  Press [SETUP] to exit.
Digital Out - DTS
OFF ON
Audio
Digital Out
Dynamic Range Conrtol  ON
Audio - Dynamic Range Control
OFF ON
Note
•  Dynamic Range Control function is available only on the discs which are recorded in the Dolby Digital format.
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE








 
						

							138
Function Setup
EN
Settings for Parental lock level
Some DVD-Video discs feature a Parental Lock level. 
Playback will stop if the ratings exceed the levels you 
set, it will require you to enter a password before the disc 
will playback. This feature prevents your children from 
viewing inappropriate material.
 Press [STOP C] if you are playing a disc.
1
 Press [SETUP].
2
 Using [K / L], select “Playback”. 
Press [ENTER].
Playback menu will appear.
.
3
 Using [K / L], select “Parental Lock”. 
Press [ENTER].Start
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE








 
						

							139
Recording
Playback
Editing
Introduction
Connections
Basic Setup
Function Setup
Others
EN
4
 Using [K / L], select the desired level. 
Press [ENTER].
Parental Lock (Default : All)
Set the Parental Lock level.
• Using [K / L], change the parental level. Press [ENTER].
ALL : 
If you select “ALL”, Parental Lock is not active. The disc will play in full.
Ratings 1 to 8 : 
Some discs contain scenes not suitable for children. If you set a rating 
for the DVD, all disc scenes with the same ratings or lower will be 
played. Higher rated scenes will not be played unless an alternative 
scene is available on the disc. The alternative must have the same rating 
or a lower one. If no suitable alternative is found, playback will stop. You 
must enter the 4-digit password or change the rating level in order to 
play the disc. 
Option window will appear. Proceed to  A  or  B .
A       A password has not been set yet.
• Using [K / L], select “Yes”. Using the Number buttons, enter a 
new password. Press [ENTER].
  Your setting will be activated.
• If you select “No”, proceed to step 5.
(Continued)
Playback
Video Audio
Parental Lock All Language
Parental Lock
8
7
6
5
4
3
2
1 All
Parental Lock
Ye s
No Change Password?Parental Lock
Password Input- ---
YES
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE








 
						

							140
Function Setup
EN
Settings for Parental lock level (cont’d)
B       A password has already been set.
• Using the Number buttons, enter the current password. 
• Using [K / L], select “Yes”. Using the Number buttons, enter a 
new password. Press [ENTER].
  Your setting will be activated.
• If you select “No”, proceed to step 5.
5
  Press [SETUP] to exit.
• If the rating set is lower than the disc rating, a message will appear. 
Select “Yes” if you want to continue playback and input the password 
followed by [ENTER].
• If there is a DVD disc inside of this unit when you set up the 
parental lock, press [OPEN/CLOSE
 A] to activate the parental lock 
level.
Parental Lock
Password Input
****
Parental Lock
Password Input- ---
Parental Lock
Ye s
No Change Password?
YES
Notes
•  Parental lock function may not be available on some discs.
•  With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock 
function operates in the way that you have set.
•  Record the password in case you forget it.
•  Press [CLEAR] to erase numbers entered incorrectly.
•  When you forget the password or you want to clear all settings in Parental lock, enter 4,7,3,7 using the Number buttons in 
Password Input window. Password will be cleared and parental levels will be set to “All”.
VODUJPOTFUVQ@6%JOEE


VODUJPOTFUVQ@6%JOEE