Toshiba B Ex4 User Guide

2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.3 Loading Supplies
 
E2- 7 
2.3.1  Loading the Media  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  10.
 Lower the Print Head Block until it stops.  
11.  After loading the media, it may be necessary to set the Media 
Sensors used to detect the print start position for label or tag printing. 
 
Setting the Feed Gap Sensor position
 
(1)  Manually move the Media Sensor so that the Feed Gap Sensor is  positioned at the centre of the labels. ( z indicates the position...

2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.3 Loading Supplies
 
E2- 8 
2.3.1  Loading the Media  (Cont.) 
  12.
 Batch mode  
In the batch mode, the media is  continuously printed and fed until 
the number of labels/tags specified in the issue command have been 
printed.  
 
 
  
 
 
 
 
 
 
 
 
 
13.  Loading with peel off module
 
When the optional Strip Module is fitted, the backing paper is 
automatically removed from the label at the Strip Plate as each label 
is printed.  
 
(1)  Remove enough...

2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.3 Loading Supplies
 
E2- 9 
2.3.1  Loading the Media  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  14. 
Loading with cutter 
When the optional Cutter Module is fitted, the media is 
automatically cut.  A disc cutter and a rotary cutter are available as 
an option, but they are used in the same way. 
Insert the leading edge of the media into the cutter until it comes out 
the Media Outlet of...

2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.3 Loading Supplies
 
E2-10 
2.3.2  Loading the Ribbon  
 
 
  There are two types of media available for printing on: these are thermal 
transfer media and direct thermal media (a chemically treated surface).  
DO NOT LOAD a ribbon when using a direct thermal media. 
 
1.
  Grasp the tabs on the top and bottom of the Ribbon Stoppers and 
move the Ribbon Stoppers back to the end of the Ribbon Shaft.   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.   Leaving plenty of slack...

2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.3 Loading Supplies
 
E2-11 
2.3.2  Loading the Ribbon  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  3.
  Slide the Ribbon Stoppers along the Ribbon Shafts to a position where 
  the ribbon is centred when fitted.  
4.   Lower the Print Head Block and set the Ribbon Shaft Holder Plate 
aligning its holes with the Ribbon Shafts.  
5.   Take up any slack in the ribbon.  Wind the leading tape onto the 
ribbon take-up roll until the ink ribbon can be...

2. PRINTER SETUP ENGLISH VERSION EO1-33089 
2.4 Connecting the Cables to Your Printer
 
E2-12 
2.4 Connecting the  Cables to Your 
Printer 
 
  The following paragraphs outline how
 to connect the cables from the 
printer to your host computer, and  will also show how to make cable 
connections to other devices.  De pending on the application software 
you use to print labels, there are 5 possibilities for connecting the 
printer to your host computer.  These are: 
•  An Ethernet connection using the...

2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.5 Turning the Printer ON/OFF
 
E2-13 
2.5  Turning the Printer  ON/OFF
 
 
 
2.5.1  Turning ON the Printer  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.5.2  Turning OFF the Printer 
 
 
 
 
 
 
  When the printer is connected to your host computer it is good practice to 
turn the printer ON before turning on your host computer and turn OFF 
your host computer before turning off the printer. 
 
 
1.
  To turn ON the printer power, press the Power Switch as...

2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-14 
2.6 Printer Setting 
 
 
 
   
Depending on the settings of your host computer or an interface to be 
used, it may be necessary to change the printer parameter settings. 
 
Follow the procedures described below 
to change the printer parameter 
settings to correspond to your environment.  
 
 
 
 
 
 
 
 
 
 
 
NOTE: 
Incorrect settings can cause the printer to function erroneously.  If you\
 have 
any problems with the parameter...

2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-15 
2.6 Printer Setting 
 (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.6.1  User System Mode  
 
„  Key functions in the system mode 
Key Function 
[MODE]  Returns to the mode menu screen. 
[CANCEL] or 
[FEED]+[RESTAR]  Returns to the upper hierarchy. 
Displays a next screen. [ENTER] or [PAUSE]
Saves the setting and returns to the upper 
hierarchy. 
Moves the cursor upward. (Note 1) [UP] or [RESTART] Increases a value. (Note 2) 
Moves the...

2. PRINTER SETUP ENGLISH VERSION EO1-33089 2.6 Printer Setting
 
E2-16 
2.6.2 Parameter Setting 
 
  The Parameter Set menu allows conf
iguring printer parameter settings. 
The following table shows the contents of the Parameter Set menu. 
 
Contents of the Parameter Set Menu  
Menu Sub menu  Parameter 
Printer Set  MEDIA LOAD Parameter 
set  (Section 2.6.2.1)  FORWARD WAIT 
   FW/BK ACT 
   HU CUT/RWD 
   RBN SAVE 
    PRE PEEL OFF 
   BACK SPEED 
  Software Set  FONT CODE 
  (Section 2.6.2.2)  ZERO...