Tone Commander 6002ta Analog Port Terminal Adapter User Guide

Tone Commander 6002TA User Manual7
Installation
Telephone operating software must be version 01.05.xx or higher to
support the 6002TA. To view the installed software version, select
VERS, then S/W from the Administration Options menu  (Setup →
ADMIN→ VERS→ S/W). If your phones software version is lower than
01.05.xx, call Tone Commander at (800) 524-0024 to request an
update.
Mounting the Base  ______________________
1. Disconnect the line cord from the telephone.
Power must be disconnected before...

8Tone Commander 6002TA User Manual
4. Replace the original base with the 6002TA terminal adapter base.
Plug the cable from the terminal adapter base into the expansion
connector on the telephone. The polarization tab on the plug must fit
into the opening on the side of the phone connector.
5.  Snap the terminal adapter base onto the phone. The base may be
rotated for wall mounting.
6.  Replace the retaining screw (required for UL compliance).
Connecting the POTS Device   ______________
Connect the analog...

Tone Commander 6002TA User Manual9
POTS Port Options
The following options can be configured from the POTS Port Options
menu:
• Ring Control• Call Waiting
•  POTS Line Privacy•  POTS Originating Call
Appearance
POTS Port Options Menu   _________________
You can enter the POTS Port Options menu at any time.
Press the Setup key.
Select POTS.
Setup
       SETUP MENU
INSTL ADMIN  USER  POTS
POTS PORT OPTIONS:
RING  PRIV  CALLWT  ORIG 

10Tone Commander 6002TA User Manual
POTS Ringing Control   ___________________
You can control the audible ringing at the analog telephone device for
each call appearance. Similar independent settings in the User Options
menu (Setup → USER
 → RING → CONTROL) control ringing at the
6210/6220 telephone – refer to the 6210/6220 User Manual.
Call appearances set to ALWAYS will ring immediately at the POTS
port.
NEVER completely disables ringing at the POTS port for the call
appearance.
WAIT delays ringing at...

Tone Commander 6002TA User Manual11
If you want to change the setting for the selected key, select
ALWAYS, NEVER, or WAIT2-WAIT7.
Press the Done key to return to the POTS Port Options menu
or the Setup key to exit Setup Mode.
POTS Line Privacy   ______________________
The Privacy setting determines whether phone and POTS calls are
mutually exclusive or if they can be swapped between the handset,
POTS port, and speakerphone.
With Privacy off, an active call can be freely passed between the
handset,...

12Tone Commander 6002TA User Manual
POTS Line Call Waiting Alert   ______________
The Call Waiting option determines whether CIDCW (Calling Identity
Delivery on Call Waiting) signaling, Call Waiting tone only, or no
signaling will be sent to the POTS port when it is active and another
inbound call arrives at the phone.
For fax or modem applications, select DISABLE to prevent interruptions
during a call.
Your analog phone must have a caller ID display and support call
waiting caller ID (CIDCW) for the...

Tone Commander 6002TA User Manual13
POTS Line Originating Call Appearance   _____
This option selects the primary call appearance used for outgoing calls
from the POTS port. If the selected call appearance is busy when
placing a call, another call appearance may be used if available.
For fax or modem applications, you can assign a secondary directory
number (if provisioned on your line) for outgoing fax or modem calls.
From the POTS Port Options menu, select ORIG.
(Setup → POTS → ORIG)
The current...

14Tone Commander 6002TA User Manual
Appendix A
Warranty and Service
Tone Commander Product Warranty
For a period of one year from date of dealer purchase, but not to
exceed 16 months from date of manufacture, Tone Commander
Systems, Inc. (Tone Commander) warrants its products to be free from
defects in material and workmanship under conditions of normal use
and service. Tone Commander shall, at its option, repair or replace any
defective product which, in its opinion, has not been misused,
damaged, or...

Tone Commander 6002TA User Manual15
Appendix B
Specifications
Contents of Shipping Container
6002TA telephone base
Manual
Compatibility
6210T, 6220T, 6210U, or 6220U ISDN phones (may require firmware upgrade)
May not be used with 6030X 30-Button Expansion Module
or 6001TA Terminal Adapter for TAPI
Capacity
Supports up to 3 standard analog telephone (POTS) devices
Connector Arrangement
One RJ-11 6-position modular jack
Battery Feed
-48 V on-hook, 50 mA maximum off-hook loop current
1000 V minimum...

16Tone Commander 6002TA User Manual
Standards Compliance
FCC Part 15, Part 68
UL, cUL 60950
Section 508 §1194.23(a) non-acoustic connection point for TTYs
Physical Dimensions
6.4” W x 5.7” D x 2.4” H, (replacement base for 6210/6220 ISDN phone)
Weight
0.5 lb.
Environmental
Operating Temperature: 32° to 104° F (0° to 40° C)
Storage Temperature: 32° to 122° F (0° to 50° C)
Humidity: 5% to 95% non-condensing