Tone Commander 6002ta Analog Port Terminal Adapter User Guide

							Tone Commander 6002TA User Manual7
Installation
Telephone operating software must be version 01.05.xx or higher to
support the 6002TA. To view the installed software version, select
VERS, then S/W from the Administration Options menu  (Setup →
ADMIN→ VERS→ S/W). If your phones software version is lower than
01.05.xx, call Tone Commander at (800) 524-0024 to request an
update.
Mounting the Base  ______________________
1. Disconnect the line cord from the telephone.
Power must be disconnected before installing the 6002TA.
Wait 10 seconds after disconnecting power before proceeding.
2. Remove the retaining screw in the center of the base.
3. Press the top of the tall edge of the base to disengage the snap
tabs, then lift the original base from the telephone body. Do not
touch the expansion connector. 
						

							8Tone Commander 6002TA User Manual
4. Replace the original base with the 6002TA terminal adapter base.
Plug the cable from the terminal adapter base into the expansion
connector on the telephone. The polarization tab on the plug must fit
into the opening on the side of the phone connector.
5.  Snap the terminal adapter base onto the phone. The base may be
rotated for wall mounting.
6.  Replace the retaining screw (required for UL compliance).
Connecting the POTS Device   ______________
Connect the analog telephone device to the jack on the back of the
base, using a standard 4 or 6-conductor cable.
WARNING:
The 6002TA is intended to connect to local analog POTS
telephone devices via relatively short (less than 300 feet) inside-
plant cabling.
Do not connect to wiring that extends outside or between buildings,
or that may be subject to electrical hazards, such as lightning or
power line crosses.
Do not connect to a telco network telephone line. Damage to the
POTS port may occur. 
						

							Tone Commander 6002TA User Manual9
POTS Port Options
The following options can be configured from the POTS Port Options
menu:
• Ring Control• Call Waiting
•  POTS Line Privacy•  POTS Originating Call
Appearance
POTS Port Options Menu   _________________
You can enter the POTS Port Options menu at any time.
Press the Setup key.
Select POTS.
Setup
       SETUP MENU
INSTL ADMIN  USER  POTS
POTS PORT OPTIONS:
RING  PRIV  CALLWT  ORIG 
						

							10Tone Commander 6002TA User Manual
POTS Ringing Control   ___________________
You can control the audible ringing at the analog telephone device for
each call appearance. Similar independent settings in the User Options
menu (Setup → USER
 → RING → CONTROL) control ringing at the
6210/6220 telephone – refer to the 6210/6220 User Manual.
Call appearances set to ALWAYS will ring immediately at the POTS
port.
NEVER completely disables ringing at the POTS port for the call
appearance.
WAIT delays ringing at the POTS port for 2 to 7 ringing cycles (6
seconds per cycle).
When using a cordless phone on the analog port, select ALWAYS for
primary call appearances, and NEVER for secondary or shared call
appearances. You can select a WAIT option on primary call
appearances when the analog phone is used as a backup answering
position; set the POTS port ring delays longer than the 6210/6220
delays to ensure that calls always ring at the 6210/6220 first.
Note – You cannot answer a call on the POTS port unless it is ringing
(ring delays have timed out).
For fax or modem applications, select ALWAYS for the fax call
appearance, and NEVER for all other call appearances. Set the
6210/6220 ringing for the call appearance to NEVER; fax/modem calls
will only ring at the POTS port.
From the POTS Port Options menu, select RING.
(Setup → POTS
 → RING)
All multifunction keys that are programmed for call
appearances or DSS will have a steady green indication.
Press a lit key to view its current POTS ring control setting.
The key’s indicator will alternately flash red and green.
KEY01=ALWAYS RING      \
ALWAYS NEVER WAIT2 WAIT3
KEY01=ALWAYS RING      \
WAIT4 WAIT5 WAIT6  WAIT7 
						

							Tone Commander 6002TA User Manual11
If you want to change the setting for the selected key, select
ALWAYS, NEVER, or WAIT2-WAIT7.
Press the Done key to return to the POTS Port Options menu
or the Setup key to exit Setup Mode.
POTS Line Privacy   ______________________
The Privacy setting determines whether phone and POTS calls are
mutually exclusive or if they can be swapped between the handset,
POTS port, and speakerphone.
With Privacy off, an active call can be freely passed between the
handset, speakerphone, or POTS port, by using the hookswitch or
Spkr key.
With Privacy on, an active call cannot be passed between the
handset/speakerphone and the POTS port.
Set Privacy ON if a fax or modem is connected to the POTS port, and
OFF for most other applications.
From the POTS Port Options menu, select PRIV.
(Setup → POTS → PRIV)
The current Privacy setting will be shown in the display.
Select ON to enable Privacy, or OFF to disable Privacy.
When finished, press the Done key to return to the POTS Port
Options menu or the Setup key to exit Setup Mode.
Done
Done
POTS LINE PRIVACY = OFF
ON    OFF 
						

							12Tone Commander 6002TA User Manual
POTS Line Call Waiting Alert   ______________
The Call Waiting option determines whether CIDCW (Calling Identity
Delivery on Call Waiting) signaling, Call Waiting tone only, or no
signaling will be sent to the POTS port when it is active and another
inbound call arrives at the phone.
For fax or modem applications, select DISABLE to prevent interruptions
during a call.
Your analog phone must have a caller ID display and support call
waiting caller ID (CIDCW) for the CALLID function to work. Call waiting
tone may still be available if provided by the ISDN network.
From the POTS Port Options menu, select CALLWT.
(Setup → POTS → CALLWT)
The current call waiting alert setting will be shown in the
display.
Select one of the displayed options.
CALLID – calling party ID is sent to the analog
telephone device, if provided by the ISDN
network. Your POTS phone must be CIDCW
compatible.
TONE – waiting calls are indicated by an alert tone.
DISABLE – call waiting alerting is disabled.
When finished, press the Done key to return to the POTS Port
Options menu or the Setup key to exit Setup Mode.
Done
CALL WAITING=CALLER ID
CALLID TONE DISABLE 
						

							Tone Commander 6002TA User Manual13
POTS Line Originating Call Appearance   _____
This option selects the primary call appearance used for outgoing calls
from the POTS port. If the selected call appearance is busy when
placing a call, another call appearance may be used if available.
For fax or modem applications, you can assign a secondary directory
number (if provisioned on your line) for outgoing fax or modem calls.
From the POTS Port Options menu, select ORIG.
(Setup → POTS → ORIG)
The current outgoing call appearance will be shown in the
display, and the CA/DN key will alternately flash red and
green.
If you want to use a different call appearance, press another
CA/DN key. Status indicators for available CA/DN keys will be
green.
When finished, press the Done key to return to the POTS Port
Options menu or the Setup key to exit Setup Mode.
Done
POTS ORIGINATING CA
CA1 
						

							14Tone Commander 6002TA User Manual
Appendix A
Warranty and Service
Tone Commander Product Warranty
For a period of one year from date of dealer purchase, but not to
exceed 16 months from date of manufacture, Tone Commander
Systems, Inc. (Tone Commander) warrants its products to be free from
defects in material and workmanship under conditions of normal use
and service. Tone Commander shall, at its option, repair or replace any
defective product which, in its opinion, has not been misused,
damaged, or improperly installed.
Repair or replacement under this warranty will be performed at Tone
Commanders factory. Authorization must be obtained from Tone
Commander prior to returning a product for repair. Freight must be
prepaid for all units returned to Tone Commander. Units repaired under
warranty will be shipped UPS Ground (or equivalent), freight prepaid by
Tone Commander.
Products that are older than the warranty period, but less than 7 years
old, or still manufactured by Tone Commander may be repaired at the
factory for a flat rate charge. Repaired out-of-warranty units are
warranted for 90 days from the date of repair.
The repair or replacement of a product under this warranty represents
the entire obligation of Tone Commander; Tone Commander shall not
be liable for any special or consequential damages resulting from or
caused by any defect, failure, incapacity or malfunction of any of its
products.
The foregoing express warranty is in lieu of all other warranties,
express or implied, including but not limited to any implied
warranty of merchantability, fitness, or adequacy for any
purpose or use, quality, productiveness or capacity; Tone
Commander, to the extent permitted by law, hereby disclaims
all such other warranties. 
						

							Tone Commander 6002TA User Manual15
Appendix B
Specifications
Contents of Shipping Container
6002TA telephone base
Manual
Compatibility
6210T, 6220T, 6210U, or 6220U ISDN phones (may require firmware upgrade)
May not be used with 6030X 30-Button Expansion Module
or 6001TA Terminal Adapter for TAPI
Capacity
Supports up to 3 standard analog telephone (POTS) devices
Connector Arrangement
One RJ-11 6-position modular jack
Battery Feed
-48 V on-hook, 50 mA maximum off-hook loop current
1000 V minimum isolation from primary (ISDN) power
Ringing
20 Hz, 70 Vrms nominal
Maximum Load: REN=3
Maximum Recommended Loop Length
300 ft (100 M) with 24-26 AWG (inside wiring only)
Transmission Characteristics
0 dB Transmit Loss, 3 dB Receive Loss ± 1 dB, 300-3000 Hz
Echo Return Loss >12 dB @600 or 900 ohms
Power Requirements
24 to 56.5 VDC, powered through 6210 or 6220 ISDN phone
Typical 1.5 W idle, 3.5 W off-hook (including 6220T ISDN phone) 
						

							16Tone Commander 6002TA User Manual
Standards Compliance
FCC Part 15, Part 68
UL, cUL 60950
Section 508 §1194.23(a) non-acoustic connection point for TTYs
Physical Dimensions
6.4” W x 5.7” D x 2.4” H, (replacement base for 6210/6220 ISDN phone)
Weight
0.5 lb.
Environmental
Operating Temperature: 32° to 104° F (0° to 40° C)
Storage Temperature: 32° to 122° F (0° to 50° C)
Humidity: 5% to 95% non-condensing