Timex Dive Casual and Performance User Manual

							DAY / DATE MODELS
TO SET THE TIME:1)   PULL the crown outto the “C” position.
2)   TURN the crown either way to the 
correct time.
3)   PUSH in the crown to the “A” position.
TO SET THE DATE: 1)   PULL the crown out to the “B” position. 
2)   TURN the crown either way to the correct date.
3)   PUSH in the crown to the “A” position.
TO SET THE DAY: 1)   PULL the crown out to the “C” position.
2)   TURN the crown either way for full 24 hour cycleto set day.
3)   PUSH the crown in to the “A” position.
7
ENGLISH
TO SET “QUICK DATE®” FEATURE: 3-Position Crown:
1)   Pull crown to “Middle” position and turn CLOCK- WISE or COUNTERCLOCKWISE until correct date
appears.
2-Position Crown:
1)   Pull crown to “OUT” position and turn CLOCKWISE until date changes. Repeat until correct date
appears. Adjust date when month has less than
31 days. Push crown in when finished.
Caution: Wearing or storing the watch with the crown
in the middle position will cause damage to the move-
ment. Always return the crown to the normal position,
or if you wish to save the battery life while storing the
watch, leave the crown in the out position.
The date function advances the date between the
hours of 10 PM and 2 AM. Avoid setting the date 
during this timeframe. If you attempt to set the date
during this time period, rotate the crown at a very
slow rate to avoid damaging the watch.
6
ENGLISH
C
B
A
CROWN 
POSITION 
 
DAY/DATE 
 
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 6 
						

							EASY SET ALARM DATE & TIME SETTINGS
TO SET THE DATE: 
1)   With the TIMEKEEPING CROWN in the “B” positionTURN the TIMEKEEPING CROWN or TURNING RING
in either direction to set the date. 
TO SET THE TIME:1)   With the TIMEKEEPING CROWN in the “C” positionTURN the TIMEKEEPING CROWN or TURNING RING
in either direction to set the time. 
EASY SET ALARM SETTINGS1)   Your easy set alarm watch is equipped with twotypes of alarms:
2)   12-Hour Alarm: rings OR vibrates twice per day at the desired hour and minute as long as the alarm
is activated. (Alarm crown must be in “E” position.)
3)   Hourly Alarm: rings OR vibrates every hour at the desired minute if activated. (Alarm crown must be
in “F” position.)
9
ENGLISH
EASY SET ALARM
EASY SET ALARM 
WITH DATE & INDIGLO®NIGHT-LIGHT1)   From the “A” position, PUSH the TIMEKEEPINGCROWN in (towards the watch case) to activate
the INDIGLO
®Night-Light and illuminate the watch
dial. 
8
ENGLISH
A B C POSITION
POSITION
D E F
ALARM CROWN
PULL CROWN “OUT” TO ACTIVATE
THE ALARM TIMEKEEPING / INDIGLO®
NIGHT-LIGHT CROWN.
PUSH CROWN TO ACTIVATE
THE INDIGLO NIGHT-LIGHT
HOUR MARKER
ALARM SET
TURNING RING MINUTE MARKER
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 8 
						

							TO SET THE HOURLY ALARM:1)   With the ALARM CROWN in the “D” position, TURNthe ALARM CROWN or TURNING RING in either
direction to set the minute alarm marker. 
2)   To activate the alarm to ring or vibrate at the desired minute, PULL the ALARM CROWN out to
the “F” position. Three beeps sound and flash 
OR a vibration indicates the Hourly Alarm is
 activated. 
3)   The alarm will sound and the dial will flash OR vibrate at the desired minute and will repeat
every hour on the specified minute unless the
alarm is deactivated. 
     NOTE:  Alarm is deactivated when the ALARM
CROWN is in the “D” position.
     If the alarm is not deactivated it will automatically stop ringing after 20 beeps and flashes OR stop
vibrating, and will resume again in one hour at
the indicated minute.
11
ENGLISH
TO SET THE 12-HOUR ALARM: 1)   With the ALARM CROWN in the “D” position,  TURN the ALARM CROWN or TURNING RING in
either direction to set the hour and minute alarm
markers. To activate the alarm to ring or vibrate at
the desired time, PULL the ALARM CROWN out to
the “E” position. A single beep sound and flash,
OR a vibration will indicate that the 12-Hour
Alarm is activated. 
2)   The alarm will sound and the dial will flash OR vibrate at the desired time (hour and minute) and
will repeat every twelve hours unless the alarm is
deactivated. 
NOTE: Alarm is deactivated when the ALARM
CROWN is in the “D” position.
If the alarm is not deactivated it will automatically
stop ringing after 20 beeps and flashes OR stop
vibrating, and will resume in 12 hours at the
indicated time.
10
ENGLISH
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 10 
						

							TO SET TIMETo set time, simply pull crown all the way out and
turn. Day and date change automatically when time
is adjusted past midnight; there is no additional step
for setting day or date. Push crown in when done.
After setting, if date changes at noon, time needs to
be adjusted ahead or back 12 hours.
If crown is accidentally put in MIDDLE position and
turned, date display will change temporarily, but date
setting is unaffected. Simply pull crown all the way
out and set time. Proper date display will resume.
7-YEAR BATTERY LIFE* WITH 
FREE LIFETIME REPLACEMENT**
If the battery needs to be changed, we recommend
that only TIMEX replace it. Your watch will need to be
recalibrated to correct time and date after changing
the battery. To return your watch to Timex use a pre-
paid shipper. To obtain a pre-paid shipper please call
1-800-448-4639 or visit the retailer where you
purchased your watch or go to www.TIMEX.com.
Please include the following with your watch to cover
13
ENGLISH
PERPETUAL CALENDARYour Perpetual Calendar watch accurately keeps
track of how many days are in each month. It also
adjusts for leap years. The date on your watch
(including the month and year) was preset at the
factory to Eastern Standard Time, Greenwich Mean
Time or Hong Kong Standard Time (depending on
where you purchased your watch). You only need to
adjust the time. 
12
ENGLISH
I
I
WED 14I       I 
WED 14
MIDDLEOUT
CHECK DATE
(FACTORY USE ONLY)SET TIME
DAY, DATE
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 12 
						

							ELAPSED TIME RINGIf your watch is equipped with a rotatable outer ring
on the face, with numbers corresponding to minutes,
you can use this Elapsed Time Ring to time an activity
from the start, or to mark the ending time for the
duration of an activity.
TO TIME AN ACTIVITY FROM THE START:Set the Start/Stop triangle at the time (hour or
minute) when you start the activity (As shown on the
left in the illustration shown below). At completion,
you can see how long the activity took.
15
ENGLISH
postage and handling (this is not a repair charge); 
a U.S.$8.00 check or money order in the U.S.; a
CAN$7.00 cheque or money order in Canada; 
In other countries Timex will charge you for postage
and  handling.
** Shipping & handling charges apply. *With
normal usage.
NEVER INCLUDE A SPECIAL WATCHBAND
OR ANY OTHER ARTICLE OF PERSONAL
VALUE IN YOUR SHIPMENT.
14
ENGLISH
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 14 
						

							TACHYMETER RINGThe tachymeter feature can be used to measure
speed in miles per hour (MPH), nautical miles per
hour (knots) or kilometers per hour (KPH) using the
sweep second hand and the scale on the wall above
the watch face. You need to know the actual  distance
you are covering in miles or km.
Start the chronograph with the second hand at zero
(the twelve o’clock position). Within the first minute,
the second hand will point to the rate for a one-mile
(or one kilometer) course: if it takes 45 seconds, the
hand will point to 80 at that position – 80 MPH or 
80 KPH.
If within the first minute, a distance greater than one
mile or kilometer is covered, multiply the tachymeter
number by the distance to get the actual rate: if you
went 1.2 miles in 45 seconds, multiply the 80 by 
1.2 – 96 MPH.
17
ENGLISH
TO MEASURE THE TIME REMAINING:Set the triangle to the hour or minute position when
you wish to complete the activity, and check the
watch periodically for progress towards that goal.
In the illustration shown on the previous page on the
right you can stop when the minute hand reaches
the 20 minutes past the hour position.
16
ENGLISH
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 16 
						

							HOW TO ADJUST BRACELET(Variations of the following bracelet sections apply to
all watch models).
SLIDING CLASP BRACELET1    Open locking plate.
2.   Move clasp to desired bracelet length.
3.   Exert pressure while holding locking plate andslide clasp back and
forth until it engages
in grooves on under-
side of bracelet.
4.   Press locking plate down until it snaps
closed. Clasp can be
damaged if excessive
force is used.
19
ENGLISH
COMPASS RINGIf your watch is equipped
with a movable ring around
the dial marked at the
letters “N”, “E”, “W”, “S” 
(for the four compass
directions) or compass
degrees, you can use this feature 
to find an approximate compass
directional reading.
1)   Lay the watch on a flat surface,or hold it so that the face is
  parallel to the ground.
2)   Locate the sun and point the hour hand at the sun.
3)   In the A.M., rotate the ring until the “S” (south) marker is halfway between the hour hand and
12:00 (after the hour hand or within the shortest
distance between the hour hand and 12:00).
4)   In the P.M., rotate the ring until “S” is before the hour hand and halfway between the hour hand
and 12:00. 
18
ENGLISH
12 1
2
3
4
5
6
7
8
9
10
11
N
SW
E
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 18 
						

							BRACELET LINK REMOVAL
REMOVING LINKS:1.   Place bracelet uprightand insert pointed tool
in opening of link.
2.   Push pin forcefully in direction of arrow until
link is detached (pins
are designed to be difficult to remove).
3.   Repeat until desired number of links are removed.
RE-ASSEMBLY:1.   Rejoin bracelet parts.
2.   Push pin back into link in opposite direction of
arrow.
3.   Press pin down securely into bracelet until it is
flush.
21
ENGLISH
FOLDOVER CLASP
BRACELET
1.   Find spring bar that  connects bracelet 
to clasp.
2.   Using a pointed tool, push in spring bar and gently
twist bracelet to disengage.
3.   Determine wrist size, then insert spring bar in correct
bottom hole.
4.   Push down on spring bar, align with top hole and
release to lock in place.
20
ENGLISH
Fig. 1
Fig. 2
Fig. 3
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 20 
						

							TIMEX INTERNATIONAL WARRANTYYour TIMEX®watch is warranted against manufacturing
defects by Timex Group USA, Inc. for a period of ONE YEAR
from the original purchase date. Timex and its worldwide
affiliates will honor this International Warranty. 
Please note that Timex may, at its option, repair your
watch by installing new or thoroughly reconditioned and
inspected components or replace it with an identical or
similar model. IMPORTANT — PLEASE NOTE THAT THIS
WARRANTY DOES NOT COVER DEFECTS OR DAMAGES TO
YOUR WATCH:
1)     after the warranty period expires;
2)     if the watch was not originally purchased from an authorized Timex retailer;
3)     from repair services not performed by Timex;
4)     from accidents, tampering or abuse; and
5)     lens or crystal, strap or band, watch case, attach- ments or battery. Timex may charge you for replacing
any of these parts.
THIS WARRANTY AND THE REMEDIES CONTAINED HEREIN
ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PUR-
POSE. TIMEX IS NOT LIABLE FOR ANY SPECIAL, INCIDENTAL
23
ENGLISH
BATTERYTimex strongly recommends that a retailer or jeweler
replace battery. If applicable, push reset button when
replacing battery. Battery type is indicated on
caseback. Battery life estimates are based on certain
assumptions regarding usage; battery life may vary
depending on actual usage.
DO NOT DISPOSE OF BATTERY IN FIRE. DO NOT
RECHARGE. KEEP LOOSE BATTERIES AWAY
FROM CHILDREN.
22
ENGLISH
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 22 
						

							Bermuda and the Bahamas +1 501 370 5775 (U.S.); France
+33 3 81 63 42 00; Germany/Austria +49 662 88921 30;
Mexico and Central America 01 800 01 06000 (U.S.);
Portugal +351 212 555 460; UK, Middle East and Africa +44
20 8687 9620
For other areas, please contact your local Timex retailer or
Timex distributor for warranty information. In Canada, the
U.S. and in certain other locations, participating Timex
retailers can provide you with a postage-paid, pre-
addressed Watch Repair Mailer for your convenience in
obtaining factory service.
©2010 Timex Group USA, Inc. TIMEX and QUICKDATE are
registered trademarks of Timex Group USA, Inc. INDIGLO is
a registered trademark of Indiglo Corporation in the US
and other countries.
25
ENGLISH
OR CONSEQUENTIAL DAMAGES. Some countries and states
do not allow limitations on implied warranties and do not
allow exclusions or limitations on damages, so these
limitations may not apply to you. This warranty gives you
specific legal rights and you may also have other rights,
which vary from country to country and state to state.
To obtain warranty service, please return your watch to
Timex, one of its affiliates or the Timex retailer where the
watch was purchased, together with a completed original
Watch Repair Coupon or, in the U.S. and Canada only, the
completed original Watch Repair Coupon or a written
statement identifying your name, address, telephone
number and date and place of purchase. Please include
the following with your watch to cover postage and
handling (this is not a repair charge): a US$ 8.00 check or
money order in the U.S.; a CAN$7.00 cheque or money
order in Canada; and a UK£2.50 cheque or money order in
the U.K. In other countries, Timex will charge you for
postage and handling. NEVER INCLUDE A SPECIAL WATCH-
BAND OR ANY OTHER ARTICLE OF PERSONAL VALUE IN
YOUR SHIPMENT.
For additional warranty information please call one of the
numbers listed below: 
Asia +852 27407311; Brazil +55 11 3068 3500; U.S. +1 800
448 4639; Canada 1 800 263 0981; the Caribbean,
24
ENGLISH
T1002-24_W217_EN_WEU_analoglayout_4  3/9/10  10:20 AM  Page 24