Tecmo World Kicks Update 1 Modification To Kicker Assembly Manual

							WORLD KICKS
UPDATE 1
MODIFICATION TO THE
KICKER ASSEMBLY 
						

							Ensure that the game is working correctly, and rectify any problems
(except kicker problems) before commencing this work.
Ensure that the game is switched OFF and the power is disconnected
before removing any parts.
Seperate the Kicker and Monitor Cabinets.
1. Remove 4off hex head screws (M6x20), with spring washers.
2. Raise the level adjusters on the Kicker Cabinet and remove the adjustable feet holders
before moving it away from the Monitor Cabinet. (Failure to raise the adjusters may
cause the adjusters to be bent or damaged).
3. Take care when moving the Kicker Cabinet not to stretch the looms before
disconnecting the connectors.
Monitor Cabinet
Hex head screw
(M6x20)
with spring washerConnectors Hex head screw
(M6x20)
With spring washer
Kicker cabinet
Adjustable foot holder 
						

							Torx security screw
(M6x20)
Torx Security screw
(M6x20)
Torx security screw
(M6x20)
Socket button
head screw
(M6x20)Hex head screw
(M10x30)
Kicker assy
Front protector
(left)
Front protector
(centre)
Front protector
(right)
Whizz nut
(M10) Fixing bracket
1. Remove 2off whizz nuts (M10) and remove the rear Fixing Bracket.
2. Remove 4off torx security screw (M6x20), 4off socket button head screw (M6x20) and
remove the Front Protectors (left and right). Remove 2off torx security screw (M6x20)
and remove the Front Protector (centre).
3. Disconnect the connectors from the Kicker Assemblies.
4. Remove 2off hex head screw (M10x30) from the front of each Kicker Assy.
5. Withdraw the Kicker Assy from the front of the cabinet. Remove the Kicker Assemblies. 
						

							Spring endsSpring shaft
Full nut
(M6)
Spring
Fitting the New Nylon Washer
1. Remove 1off Full nut (M6) and remove the Spring Shaft complete with Spring, and
Spring Ends.
2. When reassembling the new Spring Shaft refit the spring ends in the opposite
positions (front spring end refitted to the back and the back spring end refitted to the
front).
3. Fit the new Nylon Washer on to the spring shaft in front of the front spring end and
refit the Spring Shaft to the Kicker Assembly.
4. Refit the shaft to the Kicker Assembly using 1off Whizz nut (M6) supplied and with
Loctite 242 applied to the thread.
Note: When tightening the Whizz nut ensure that the nut welded to the shaft is retained
with a spanner to ensure that the Whizz nut is fully tightened. Failure to tighten the
Whizz nut fully may allow the shaft to come loose during game play causing damage
to the shaft.
Spring endsSpring shaftWhizz nut (M6)
(fit with
Loctite 242
applied)
Spring
Reverse positions of spring ends
when refitting to the new shaft.
New Nylon Washer
(Part No 47000208) 
						

							Re-assembly and Testing
1. Refit the Kicker Assemblies to the cabinet.
2. Refit the Front Protectors.
3. Rejoin the Kicker Cabinet to the Monitor Cabinet.
(Take care not to trap any wires when rejoining the cabinets).
4. Refit the Adjustable Feet Holders and lower the Level Adjusters.
5. Re-initialize the game.
The following operation 
must always be performed after replacing the NAOMI Game
PCB, Joystick Potentiometers or initializing the backup data..
The game will not operate correctly if these adjustments are not made.
a) Slide the TEST switch ON while pressing and holding the SERVICE switch. The
following screen is displayed.
b) Ensure that all joysticks are in their central position, then press the Service button to
initialize the setting details.
c). Press the Enter button to go to the Switch Test and confirm correct joystick operation.
(see next page for test details)I/F INITIALIZE
KEEP STICKS CENTRE POSITION
AND PRESS SERVICE SW
GO TO [SWITCH TEST] ............................ (a)
SELECT SW :CHOOSE ENTER SW : ENTER 
						

							Switch Test
When Switch Test is selected and entered from the I/F Initaialize screen the following
screen is displayed.
I/O TEST
LINK : OFF
SWITCH TEST [ON : RED]
COIN 0 (1)
SERVICE OFF (2)
TEST OFF (3)
SELECT (UP/DOWN) OFF/OFF (4)
ENTER OFF (5)
STICK
   (L / R) 8765 7765 6765 5765 (7)
   (U / D) 8765 7765 6765 5765 (8)
BUTTON OFF OFF OFF OFF (9)
   KICK 0000 0000 0000 0000 (10)
 (FRONT / BACK) OFF/OFF OFF/OFF OFF/OFF OFF/OFF (11)
(12)
UP SELECT SW  +  ENTER SW  :  EXIT
(6)
The SWITCH TEST screen displays the status of the switches.
The display changes when any of the switches are operated.
Press both Select Up switch and Enter Switch together to exit and return to the Menu.
(1) The number increments each time a coin signal is received.
(2) ~ (5) The display changes from OFF to ON each time the respective switch is
operated.
(6) A bar extends from the centre corresponding to the direction and deflection
of the joystick.
(7) & (8) The figure changes corresponding to the joystick angle when the joystick is
tilted. The figure will change colour when the joystick is tilted to its
maximum angle of defelection.
(7) is for the left/right direction, and (8) is for the forward/backward
direction.
(9) The dispaly changes from OFF to ON when either of the start buttons are
pressed.
(10) Displays the input force of the ball assembly used during the game.
(11) The left OFF changes to ON, (ON/OFF), when the ball is kicked gently and
the right OFF changes to ON, (ON/ON), when the ball is kicked hard.
(12) A red bar is displayed above the line when the ball is kicked. The bar
length indicates the kick speed.