Technics Stereo Integrated Amplifier Su C700 Owners Manual

							11
You can input analog audio signals to this unit and play back music.
*1 When connecting to a record player with a built-in PHONO equa lizer, connect its cable to the analog audio input terminal [LINE IN].
*2 When connecting a record player with a ground wire, connect t he ground wire to the PHONO EARTH terminal [PHONO EARTH] of this unit.
You can input digital audio signals to this unit and play back music.
	
≥The digital audio input of this unit supports only the linear P CM (LPCM) signals listed below. For details, refer to the opera ting instructions of the 
connected device.
Connecting to analog audio output devices
e.g.,
Record player*
1This unit (rear) Blu-ray Disc player, etc.
Audio cable
(not supplied) Audio cable
(not supplied)
Connecting to digital audio output devices
e.g.,
CD player, etc. This unit
(rear) CD player, etc.
Optical digital audio cable (not supplied) Coaxial digital cable
(not supplied)
Input terminalSampling frequencyNumber of quantization bits
Coaxial digital input 32/44.1/48/88.2/96/176.4/192 kHz 16/24 bit
Optical digital input 32/44.1/48/88.2/96 kHz16/24 bit
*2
SU-C700-SQT0489_PP_mst.book  11 ページ  ２０１５年１月７日　水曜日　午前１０時３２分 
						

							12
Connect only after all other connections are completed.
	
≥This unit consumes a small amount of AC power ( >17) even the power switch lever is in the [OFF] position. Remove the plug from the main 
electrical outlet if you will not  be using the unit for an extended period of time. Place the unit so the plug can be easily r emoved.
AC power supply cord connection
This unit
(rear)
To a household AC outlet
AC power supply cord (supplied)
Insert the AC power supply cord up to 
A, a point just before the round hole.
SU-C700-SQT0489_PP_mst.book  12 ページ  ２０１５年１月７日　水曜日　午前１０時３２分 
						

							13
To optimize the audio output, you can measure the amplifier 
characteristics and correct its output when it is connected to 
the speakers.
≥Disconnect the headphones. If you connect them during amplifier  
characteristic measurement or amplifier output correction, it w ill be 
canceled.
1Raise the power switch lever of this unit to 
the [ Í/I] position.
2Press and hold [LAPC] until the LAPC 
indicator on this unit starts to blink.
≥ This unit will start measuring the characteristics of the 
amplifier. Check that a test tone is output from both the 
left and right speakers.
– If you press [LAPC] while the measurement is in progress, it 
will be canceled. The LAPC indica tor on this unit will go off.
≥When the measurement is complete, amplifier output 
correction will be automatically turned on. The LAPC 
indicator on this unit will light up.
∫ Turning on/off the output correction 
function
Press [LAPC].
Each time you press the button:
	≥Depending on the type of the connected speakers, the effect of  the 
output correction function may be minimal.
≥ The corrected output remains in effect until you measure the 
characteristics again. When you use other speakers, redo the 
measurement.
Operations
≥Reduce the volume to minimum.
1Raise the power switch lever of this unit to 
the [ Í/I] position.
2Press [ NINPUT O] below [AMP] to select 
the input source.
The indicator of the selected input source will light up.
3Operate the device to be used for playback.
4Press [ rVOL s] to adjust the volume.
Measuring the characteristics 
of the amplifier and correcting 
its output
Test tone emitted during measurement
To ensure the measurement accuracy, the speakers 
output a test tone at regular intervals. (For approximately 
4minutes)
It is not possible to change the volume of the audio being 
output while the measurement is in progress.
LAPC indicator lights up On
LAPC indicator goes offOff
PHONOAnalog audio input (PHONO)
LINEAnalog audio input (LINE IN)
PCDigital audio input (PC) ( >15)
COAX1 ≥
Digital audio input (COAX1 IN)
≥ ST-C700
COAX2 ≥
Digital audio input (COAX2 IN)
≥ SL-C700
COAX3 Digital audio input (COAX3 IN)
OPTDigital audio input (OPT IN)
SU-C700-SQT0489_PP_mst.book  13 ページ  ２０１５年１月７日　水曜日　午前１０時３２分 
						

							14
This unit is designed to conserve its power consumption and 
save energy. The unit will turn to standby mode automatically 
if there is no sound and it is not being used for approximately 
20 minutes.
≥ The factory default is “On”.
To cancel this function
1Press and hold [MUTE] until the PHONO 
indicator on this unit starts to blink.
2Press [MUTE].
Each time you press the button:
3Press [VOL s] to exit.
	
≥ You will exit the auto off setup mode if you do not operate any  
buttons and controls for approximately 10 seconds after any of  the 
three indicators above starts blinking.
When other equipment responds to the supplied remote 
control, change the remote control code.
≥ The factory default is “1”.
Point the remote control at this unit, and 
press and hold [OK] and the numeric button 
for at least 4 seconds.
≥When the code is changed, the PC indicator and the 
COAX2 indicator blink for approximately 10 seconds.
	
≥ When the ST-C700/SL-C700 is connected via the system control 
function, change its remote control code as well as the remote 
control code for this unit.
You can automatically link this unit with the ST-C700/SL-
C700 and operate them easily with the remote control.
Preparation
1 Connect this unit and the ST-C700/SL-C700 with system 
connection cables and coaxial digital cables. ( >10)
2 Set the power switch lever of this unit and the ST-
C700/SL-C700 to the [Í/I] position.
∫Switching this unit and the ST-C700/SL-C700 
to on/standby simultaneously
≥If you point the remote control at this unit and press 
[AMP Í] when this unit and the ST-C700/SL-C700 are in 
standby mode, this unit and the device of the selected input 
source will be turned on simultaneously.
≥ If you point the remote control at this unit and press 
[AMP Í] when this unit and the ST-C700/SL-C700 are 
turned on, this unit and the ST-C700/SL-C700 will 
simultaneously enter standby mode.
∫ Switching this unit’s input source 
automatically
When you perform an operation such as playback on the ST-
C700/SL-C700, the input source of this unit will be 
automatically switched to “COAX1”/“COAX2”.
	
≥For information on the operations of the ST-C700/SL-C700, pleas e 
also refer to their operating instructions.
≥ If you install the dedicated app “Technics Music App” (free of 
charge) on your tablet/smartphone, you can use a wide variety o f 
functions when the unit and the ST-C700 are connected.
For details, visit:
www.technics.com/support/
Auto off function
COAX3 indicator blinks On
OPT indicator blinksOff
Remote control code
[OK] + [1]Set the code to 1
[OK] + [2]Set the code to 2
Using the system control 
function
SU-C700-SQT0489_PP_mst.book  14 ページ  ２０１５年１月７日　水曜日　午前１０時３２分 
						

							15
Listening to audio from a PC, etc.
You can connect the digital audio input terminal [PC] and a PC, etc. with a USB cable and play back music on the PC, etc. with 
this unit.
(as of November 2014)
1Disconnect the AC power supply cord.
2Connect this unit and a PC, etc.
3Connect the AC power supply cor d to this unit, and raise the power switch lever to the [Í/I] 
position. ( >12)
4Press [ NINPUT O] below [AMP] repeatedly to select “PC”.
5Operate the PC, etc. for playback.
6Press [ rVOL s] to adjust the volume.
≥ OS X is a trademark of Apple Inc., registered in the U.S. and o ther countries.
≥ Windows and Windows Vista are either registered trademarks or t rademarks of Microsoft Corporation in the United States and/or other 
countries.
Connecting to a PC
Before connecting to a PC, follow the steps below.
≥ Refer to the following for the recommend OS versions for your P C:
– Windows Vista, Windows 7, Windows 8, Windows 8.1
– OS X 10.7, 10.8, 10.9, 10.10
1 Download and install the dedicated driver to the PC. (Only for  Windows OS)Download and install the driver from the website below.
www.technics.com/support/
2Download and install the dedicated app “Technics Audio Player” (free of charge) on your PC. (Common to both Windows 
OS and OS X)
Download and install the app from the website below.
www.technics.com/support/
e.g.,
PC, etc. This unit
(rear)
USB 2.0 cable
(not supplied)
Ty p e   A Ty p e   B
SU-C700-SQT0489_PP_mst.book  15 ページ  ２０１５年１月７日　水曜日　午前１０時３２分 
						

							16
Troubleshooting
Before requesting service, make the following checks. If you 
are uncertain about some of the check points, or if the 
solutions indicated in the following guide does not resolve 
the issue, then consult your dealer for instructions.
Heat buildup of this unit.
≥This unit becomes warm when the volume is high. This is 
not a malfunction.
A “humming” sound can be heard during 
playback.
≥An AC power supply cord or fluorescent light is near the 
cables. Keep other appliances and cords away from the 
cables of this unit.
≥ Set the [ATTENUATOR] switch to [ON]. ( >7)
≥ A strong magnetic field near a TV or other device may 
adversely affect the audio quality. Keep this unit away from 
such devices.
≥ The speakers may output noise when a device nearby is 
emitting powerful radio waves, such as when a mobile 
phone is on a call.
No sound.
≥Check connections to speakers and other equipment.
After checking the connections, measure the 
characteristics of the amplifier. ( >13)
≥ Check to see if the correct input source is selected.
≥
Insert the plugs of the cables to be connected all the way in.
≥ Playback of multi-channel content is not supported.
≥ The digital audio input terminals of this unit can only detect 
linear PCM (LPCM) signals. For details, refer to the 
operating instructions of the 
connected device.
The remote control does not work properly.
≥To avoid interference, please do not put any objects in front 
of signal sensor. ( >7)
≥ Change the remote control code if other products react to 
this remote control. ( >14)
Pressing [DIMMER] changes the display and the 
basic control switches brightness of the ST-
C700/SL-C700.
≥[DIMMER] works for the ST-C70 0/SL-C700 as well as this 
unit. Turn off the device that you want to maintain the 
brightness level of, and press [DIMMER].
The peak power meter does not operate.
≥ In the following cases, this meter does not operate:– When a headphone plug is connected.
– When the peak power meter light is turned off by pressing 
[DIMMER].
– When this unit is muted by pressing [MUTE].
The system control function is not working.
≥ Use the system connection cables supplied with the ST-
C700/SL-C700.
≥ Connect the system connection cables to the system 
terminals [CONTROL1]/[CONTROL2].
Connect the ST-C700 to [CONTROL1] and the SL-C700 to 
[CONTROL2].
≥ Connect coaxial digital cables to the digital audio input 
terminals [COAX1 IN]/[COAX2 IN].
Connect the ST-C700 to [COAX1 IN] and the SL-C700 to 
[COAX2 IN].
The unit turns off automatically.
≥Is the auto off function turned on? ( >14)
≥ If the ST-C700 is connected to this unit via the system 
control function, this unit may automatically enter standby 
mode when the ST-C700 enters standby mode. ( >10, 14)
≥ This unit incorporates a protection circuit to prevent 
damage caused by heat buildup. When you use this unit at 
a high volume level for a long period of time, it may turn off 
automatically. 
Wait for this unit to cool down before turning on this unit 
again. (For approximately 3 minutes)
Input indicator blinks.
≥In the following cases, the input indicator blinks:– When this unit is muted by pressing [MUTE].
– “PC”, “COAX1”, “COAX2”, “COAX3” or “OPT” is selected, but no 
device is connected.
– Audio signals, such as sampling frequency components, are not  input correctly.
To return all settings to the factory defaults
When the following situations occur, reset the memory:
≥There is no response when buttons are pressed.
≥ You want to clear and reset the memory contents.
When the unit is off:
1 Press and hold [AMP Í].
2 While continuing to hold [AMP Í], raise the power 
switch lever of this unit to the [ Í/I] position.
≥Keep holding [AMP Í] until the PC indicator and the 
COAX2 indicator blink twice.
SU-C700-SQT0489_PP_mst.book  16 ページ  ２０１５年１月７日　水曜日　午前１０時３２分 
						

							17
Specifications
	
≥Specifications are subject to change without notice.
≥ Mass and dimensions are approximate.
≥“Direct Stream Digital”, DSD and their logos are trademarks of  Sony Corporation.
∫GENERAL
Power supply AC 120 V, 60 Hz
Power consumption 73 W
Power consumption in standby mode Approx. 0.3 W
Power consumption in off mode Approx. 0.3 W
Dimensions (Wk Hk D) 340 mm k132 mm k325 mm (13
3/8qk 57/32qk1213/16q)
Mass (Weight) Approx. 8.3 kg (18.3 lbs)
Operating temperature range 0oC to r 40oC( r32 oF to  r104 oF)
Operating humidity range 35 % to 80 % RH (no condensation)
∫AMPLIFIER SECTION
FTC output power 45 W r 45 W (20 Hz to 20 kHz, T.H.D. 0.5 %, 8 ≠, 20 kHz LPF)
70 W  r 70 W (20 Hz to 20 kHz, T.H.D. 0.5 %, 4 ≠, 20 kHz LPF)
Load impedance 4≠ to 16 ≠
Frequency response
PHONO (MM) 20 Hz to 20 kHz (RIAA DEVIATION w1 dB, 8 ≠)
LINE 20 Hz to 80 kHz (s3 dB, 8 ≠)
COAX1/2/3 20 Hz to 90 kHz (s3 dB, 8 ≠)
Input sensitivity/Input impedance
LINE 200 mV / 22 k≠
PHONO (MM) 2.5 mV / 47 k≠
∫TERMINALS SECTION
Headphones jack Stereo, ‰6.3 mm (1/4q)
USB port
USB Standard USB 2.0 high-speed
USB Audio Class specification USB Audio Class 2.0, Asynchronous  mode
Connector USB Standard B connector
Format support LPCM (32/44.1/48/88.2/96/176.4/192 kHz, 16/24/32 bit)
DSD (2.8224 MHz, 5.6448 MHz)
DSD control mode ASIO Native mode, DoP mode
DSD64/DSD128 playback
Channel 2ch
Analog input Line input Pin jack
PHONO (MM) Pin jack
Digital input
Optical digital input Optical terminal
Coaxial digital input  k3 Pin jack
Format support LPCM
System port
System control  k2 ‰3.5 mm (
1/8q) jack
SU-C700-SQT0489_PP_mst.book  17 ページ  ２０１５年１月７日　水曜日　午前１０時３２分 
						

							18
n
Limited Warranty (ONLY FOR U.S.A.)
Technics Products – Limited Warranty
Limited Warranty Coverage
(For USA Only)
If your product does not work properly because of a defect in m aterials or 
workmanship, Panasonic Corporation of North America (referred t o as “the 
warrantor”) will, for the length of the period indicated on the  chart below, which 
starts with the date of original purchase (“warranty period”),  at its option either (a) 
repair your product with new or refurbished parts, (b) replace  it with a new or a 
refurbished equivalent value pr oduct, or (c) refund your purcha se price. The 
decision to repair, replace or refund will be made by the warra ntor.
During the “Labor” warranty period there will be no charge for  labor. During the 
“Parts” warranty period, there  will be no charge for parts. This Limited Warranty 
excludes both parts and labor for non-rechargeable batteries, a ntennas, and 
cosmetic parts (cabinet). This warranty only applies to products purchased and 
serviced in the United States. This warranty is extended only t o the original 
purchaser of a new product which was not sold “as is”.
Mail-In Service--Online Repair Request
Online Repair Request
To submit a new repair request and for quick repair status visi t our Web Site at 
www.panasonic.com/support.
When shipping the unit, carefully pack, include all supplied ac cessories listed in 
the Owner’s Manual, and send it prepaid, adequately insured and  packed well in 
a carton box. When shipping Lithium Ion batteries please visit  our Web Site at 
www.panasonic.com/BatteryHandling
 as Panasonic is committed to 
providing the most up to date information.  Include a letter detailing the complaint, 
a return address and provide a daytime phone number where you c an be 
reached. A valid registered receipt is required under the Limit ed Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE 
PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits and Exclusions
This warranty ONLY COVERS failures due to defects in materials  or 
workmanship, and DOES NOT COVER normal wear and tear or cosmeti c 
damage. The warranty ALSO DOES NOT COVER damages which occurred  in 
shipment, or failures which are caused by products not supplied  by the 
warrantor, or failures which result from accidents, misuse, abu se, neglect, 
mishandling, misapplication, alteration, faulty installation, 
set-up adjustments, misadjustm ent of consumer controls, imprope r 
maintenance, power line surge, lightning damage, modification,  introduction of 
sand, humidity or liquids, commercial use such as hotel, office , restaurant, or 
other business or rental use of the product, or service by anyo ne other than a 
Factory Service Center or other Authorized Servicer, or damage  that is 
attributable to acts of God. THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER 
“LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR 
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS 
PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.
(As examples, this excludes dam
ages for lost time, travel to and from the 
servicer, loss of or damage to media or images, data or other memory or 
recorded content. The items listed are not exclusive, but for i llustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY 
OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED 
WARRANTY.
Some states do not allow the exclusion or limitation of inciden tal or 
consequential damages, or limitations on how long an implied wa rranty lasts, so 
the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also  have other rights 
which vary from state to state. If a problem with this product  develops during or 
after the warranty period, you may contact your dealer or Servi ce Center. If the 
problem is not handled to your satisfaction, then write to: Consumer Affairs Department
Panasonic Corporation of North America
661 Independence Pkwy 
Chesapeake, VA 23320
PARTS AND SERVICE, WHICH ARE NO T COVERED BY THIS LIMITED 
WARRANTY, ARE YOUR RESPONSIBILITY.
As of October 2014
Product or Part NamePartsLabor
Technics Stereo Integrated Amp
3 (three) years 3 (three) years
Technics Network Audio Player
Technics Speaker System
Technics Compact Disc Player 2 (two) years 2 (two) years
for all your Technics gear
Go to 
www.panasonic.com/accessories
Get everything you need to get the most out of 
your Technics products
Accessories & Parts for your Camera, Phone, A/V 
products, TV, Computers & Networking, Personal  Care, Home Appliances, Headphones, Baeries,  Backup Chargers & more…
Customer Services Directory
For Product Informaon, Operang Assistance, 
Parts, Owner’s Manuals, Dealer and Service info  go to www.panasonic.com/support
For the hearing or speech impaired TTY: 1- 877-833-8855
The model number and serial number of this product can be 
found on either the back or the bottom of the unit.
Please note them in the spac e provided below and keep for 
future reference.
MODEL NUMBER
SU-C700
SERIAL NUMBER
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
SU-C700-SQT0489_PP_mst.book  18 ページ  ２０１５年１月７日　水曜日　午前１０時３２分 
						

							19
Limited Warranty (ONLY FOR CANADA)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
TECHNICS PRODUCT – LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use and for a 
period as stated below from the date of original purchase agree s to, at its option either (a) repair your product with new or 
refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The  
decision to repair, replace or refund will be made by Panasonic  Canada Inc. 
This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Technics brand 
product mentioned above sold by an authorized Panasonic dealer  in Canada and purchased and used in Canada, which product 
was not sold “as is”, and which product was delivered to you in new condition in the original packaging. 
IN ORDER TO BE ELIGIBLE TO RECE IVE WARRANTY SERVICE HEREUNDER,  A PURCHASE RECEIPT OR OTHER 
PROOF OF DATE OF ORI GINAL PURCHASE, SHOWING  AMOUNT PAID AND PLACE OF PURCHASE
 IS REQUIRED
LIMITATIONS AND EXCLUSIONS
This warranty ONLY COVERS failures due to defects in materials  or workmanship, and DOES NOT COVER normal wear and 
tear or cosmetic damage. The warranty ALSO DOES NOT COVER damag es which occurred in shipment, or failures which are 
caused by products not supplied by Panasonic Canada Inc., or fa ilures which result from accidents, misuse, abuse, neglect, 
mishandling, misapplication, alteration, faulty installation, s et-up adjustments, misadjustment of consumer controls, improper  
maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as 
hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than an Authorized Servi cer, or 
damage that is attributable to acts of God.
Dry cell batteries are also excluded from coverage under this w arranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY 
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU LAR PURPOSE. IN NO EVENT WILL 
PANASONIC CANADA INC. BE LIABLE  FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING 
FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF AN Y EXPRESS OR IMPLIED WARRANTY. (As 
examples, this warranty excludes damages for lost time, travel  to and from the Authorized Servicer, loss of or damage to media  or 
images, data or other memory or recorded content. This list of  items is not exhaustive, but for illustration only.)
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or t he 
exclusion of implied warranties, so the above limitations and e xclusions may not be applicable. This warranty gives you specif ic 
legal rights and you may have other rights which vary depending  on your province or territory.
WARRANTY SERVICE
For product operation, repairs and information assistance , please visit our Support page on:
www.panasonic.ca/english/support
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and prefera bly in the original carton.
Include details of the defect claimed, and proof of date of original purchase.
Technics Stereo Integrated Amp 3 (three) years parts and labour
Technics Network Audio Player 3 (three) years parts and labour
Technics Speaker System 3 (three) years parts and labour
Technics Compact Disc Player 2 (two) years parts and labour
SU-C700-SQT0489_PP_mst.book  19 ページ  ２０１５年１月７日　水曜日　午前１０時３２分 
						

							Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102-5490
http://www.panasonic.comPanasonic Canada Inc.
5770 Ambler Drive, 
Mississauga, Ontario, 
L4W 2T3
www.panasonic.com
C Panasonic Corporation 2015
Printed in Malaysia
p
SQT0489F0115BM0
SU-C700-SQT0489_PP_mst.book  20 ページ  ２０１５年１月７日　水曜日　午前１０時３２分