Taxan Projector U6 232 User Manual

8English 9 English
8English 9 English

 Introduction

1.  Control Panel
2.  Zoom Lever
3.  Power Socket
4.  Focus Ring
5.  Adjuster 
6.  Adjuster Button
7.  Remote Control Sensor
8.  Tilt Adjuster
9.  Connection Ports
Main Unit
  Product Overview
1
2
3
4
5
6
1
7
9
8
8 

8English 9 English
8English 9 English

Introduction

 Control Panel
1.  Power/Standby Button
2.  Menu Button
3.  Source Button
4.  Keystone Correction Button
5.  Enter Button
6.  Auto Button
7.  Four Directional Select Keys Buttons
8.  Temp Indicator  
9.  Lamp Indicator 
10.  Power Indicator 
5
7
3
10
4
4
6
2
1
98 

10English 11 English
10English 11 English

 Introduction

 Connection Ports
1.  Control(RS232) Connector
2.  Monitor Loop-through Output Connector
3.  Composite Video Input Connector
4.  S-Video Input Connector
5.  Audio Input Connector
6.  PC Analog signal/SCART RGB/HDTV/Component Video 
Input Connector
7.  Audio Output Connector
8.  KensingtonTM Lock Port
8
134562
7 

10English 11 English
10English 11 English

Introduction

Wireless Remote Control
1.  Power
2.  Infrared Transmitter 
3.  Menu
4.  Aspect
5.  Volume +/-
6.   Computer Source
7.  S-Video Source
8.  Video Source
9.  Auto
10.  Four Directional Select 
Keys
11.  D-Zoom
12.  Mute
13.  Freeze
14.  Picture Mute
15.  Quick Color Adjustment
16.  Keystone Correction
17.  Enter
12
 16
 9
 6
 5
 4
 3
 8
 7
 11
 12
 14
 13
 15
 10
 17 

12English 13 English
12English 13 English

Installation

 Connecting the Projector
Due to the difference applications for each country, some regions may have different accessories.
1.........................................................................\
.....................................Power Cable2.........................................................................\
............................RGB Signal Cable3.........................................................Audio IN Cable...

12English 13 English
12English 13 English

 Installation

Powering On the Projector
1.  Remove the lens cap. 
2.  Ensure that the power cable and RGB signal cable are 
securely connected. The Power LED will fl  ash green.
3.  Turn on the lamp by pressing “Power/Standby” button on 
the control panel.  And the Power LED will turn green. 
The fi  rst time you use the projector, you can select your 
preferred language from quick menu after the startup screen 
display.
4.  Turn on the power of the connected...

14English 15 English
14English 15 English

Installation

Warning Indicator
  When the “LAMP” indicator lights solid red, the projector 
will automatically shut itself down. Please contact your local 
reseller or an authorized service center. 
  When the “TEMP” indicator lights solid red for about 15 
seconds, it indicates the projector has been overheated. The 
projector will automatically shut itself down.
  Under normal conditions, the projector can be switched on 
again after it has cooled down. If...

14English 15 English
14English 15 English

 Installation

 Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt adjuster
The projector is equipped with an adjuster for adjusting 
the image height.
 To raise the image:
1.  Press the adjuster button . 
2.  Raise the image to the desired height angle , then release  
  the button to lock the adjuster into position.
3.  Use  to fi  ne-tune the display angle. 
 To lower the image:
1.  Press the adjuster button.
2.  Lower the image, then...

16English 17 English16English 16English 17 English
Installation
Focus Ring
Zoom Lever
Adjusting the Projector Zoom / Focus
You  may  turn  the  zoom  lever  to  zoom  in  or  out.    To  focus  the 
image, rotate the  focus ring until the image is clear. The projector 
will focus at distances from 4.92 to 38.75 feet (1.5 to 11.8 meters) 
with mechanical travel.
Adjusting Projection Image Size
There is a tolerance of ± 5% due to design values.
This table uses the lens apex and lens center as references...

16English 17 English16English 17 English17 English
 User Controls
Control Panel
 Control Panel & Remote Control
There are two ways for you to control the functions: 
Remote Control and Control Panel.
 Using the Control Panel
  Power/Standby  
Refer to the “Power On/Off the Projector” section on pages 13-14.
 Source  
Press “Source” to choose Computer, Component-p, Component-i, Composite, S-video source.
 Menu 
Press “Menu” to launch the on screen display (OSD) menu. To exit OSD, press “Menu” again....