Taxan Projector KG Ps 125x User Manual

E-10
Names of the Main Unit Parts
SOURCE
KEYSTONEAUTO
KEYSTONE
P
O
W
E
R
S
T
A
N
D
B
YST
A
TU
S
M
E
N
U
Q
U
IC
K M
E
N
U
Adjuster button [E-25]
Focus ring [E-25] Exhaust vents
Front adjuster [E-25]
Lamp cover [E-59] Remote control
sensor [E-13]
LensVentilation slots
Rear adjusters [E-25] Speaker
Lens cover Zoom ring [E-24] 

E-11
Names of the Main Unit Parts
SOURCE
KEYSTONEAUTO
KEYSTONE
POWER
STANDBYSTATUS
MENU
QUICK MENU
SOURCE
KEYSTONE
AUTO
KEYSTONEPOWER
STANDBY STATUS
MENU QUICK MENU
SD CARD
S-VIDEO VIDEO AUDIOCOMPUTER IN
USB slot
See Page 15 (“Image Viewer / Wireless Network”
section)
AUDIO connector [E-20] COMPUTER IN connector [E-16, 19] S-VIDEO connector [E-18]
VIDEO connector [E-18]Ventilation slotKeystone Manual Adjustment
button [E-29]
SOURCE button [E-26] AUTO button [E-26]
ENTER button [E-34] SELECT (
)...

E-12
Names of the Remote Control Parts
Precautions
Handling of the Remote Control
* Do not drop the remote control or handle it inappropriately.
* Do not expose the remote control to water or other liquids. Should the remote control become wet, wipe it dry
immediately.
* Try to avoid use in hot and/or humid locations.
* Please keep button battery out of the reach of children. If a battery is swallowed, promptly obtain the medical care of
a doctor.
* Remove the battery from the remote control when it is...

E-13
Using the remote control for the first time
The battery compartment is fitted with a transportation insulation sheet at the time of shipping. Pull
out the sheet and remove it. The remote control is now ready for use.
Replacement Method
1(A) With the knob pressed to
the right side, (B) draw out the
battery case.2Remove the old battery and in-
stall a new button battery with (+)
side facing upward in the battery
holder.3Insert the battery holder into the re-
mote control and push in until the
battery...

E-14
The Procedure Up to Projecting to the Screen
Perform setup adjustments in the following order.
1Position the projectorDetermine the locations to set up the screen and the projector.
See “Placement Guide” on Page E-15.
2Connect the video equipment and personal computer
Connect your equipment to the projector.
When making connections with the personal computer’s RGB connector, see “Connections with
Personal Computer” on Page E-16.
When making connections with the video equipment’s video connector or...

E-15
Placement Guide
• Use this information as a guide to find out about the screen size when the projector is placed at a certain location, or
to find out the approximate size of a screen that will be required.
• The projection distance over which focussing is adjustable is 1.20 m (3.9 feet) to 11.78 m (38.65 feet). The projector
should be placed within this range.
* There is a tolerance of ±5% due to design values.
* This table uses the lens apex and lens center as references and requires that the...

E-16
Connecting Personal Computers and Video Equipment
Connecting this unit with a personal computer permits presentation data to be projected as a large screen display at
conferences, lectures, and on other occasions. Furthermore, connecting this unit to a DVD player or other video equip-
ment source in combination with an audio/video amplifier and speaker system will allow you to enjoy convincing home
theater.
MONITOR OUT
Personal
computer
RGB signal cable (Supplied item)
Note:
* Before making...

E-17
Connecting Personal Computers and Video Equipment
To Output the External Output Signal of a Notebook Computer
When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook
computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your
notebook computer or the on-line help while performing the following procedure.
1Check whether a signal is being sent from the notebook...

E-18
VIDEOS-VIDEO
Connecting Personal Computers and Video Equipment
Connections with Composite Signals
Video Equipment with VIDEO Connectors
•Connect to the projector’s VIDEO connector using a commercially available video cable.
•The input setting of the VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project, please
change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input Format]
→ [Video].
See “Input...

E-19
CrCbY
Pr Pb YCOMPONENT
COMPONENT
Connecting Personal Computers and Video Equipment
Connections with Component Signals
When the Video Equipment Has a YCbCr Connector or YPbPr Connector
•The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “Compo-
nent” using the menu sequence of [Setup] → [Input Format] → [Computer].
See “Input Format” on Page E-49.
•When projecting the YCbCr signal or YPbPr signal, if the color of the overall image...