Tascam TM-D1000 Operational Quick Reference Guide

							+Initializing TM-D1000 internal data
Hold and press the PARAM SEL and ENTER keys while powering on the TMD-1000, and 
press 
ENTER after selecting All, Snapshot or Effect(see page 10).
+Setting the word clock
Option à System à Master Clock Select (see ÒWord synchroniza-
tionÓ on page 16).
+Selecting record or mixdown mode
Option à MODE à MODE select (see ÒChoosing REC or MIX modeÓ on 
page 11).
+Selecting Buss Function (group/aux allocations)
Option à MODE à BUSS Function select (see ÒBuss conÞgurationsÓ 
on page 11).
+Assigning channels to busses
Press the channelsÕs CH SEL key, and then the appropriate CH ASSIGN key(s) (see ÒRout-
ing channels to bussesÓ on page 18).
+Bypassing the group buss system
Press the channelÕs CH SEL key, and then the DIRECT OUT key, making sure the channel 
is not assigned to a group buss (see ÒUsing the DIRECT OUTsÓ on page 19).
+Monitoring input channels and tape tracks
Assign the input channels and tape tracks to the stereo L-R buss (see ÒMonitoring, etc.Ó on 
page 21).
+Panning channels between output busses
Use the PA N controls above each channel fader.
+Making EQ settings
Press the PARAM SEL key until the EQ indicator lights green, and then the channelÕs CH 
SEL
 key. Make sure the EQ key by the CH ASSIGN keys is lit, and make the appropriate 
settings using the data editing knobs (see ÒEqualizationÓ on page 18).
+Making stereo linked pairs of channels
Press and hold down the CH SEL key of an odd-numbered channel, and press the CH SEL 
key of the next even-numbered channel (you can also press and hold any even-numbered 
key and press odd-numbered key directly before it)Ñsee ÒLinking channels for simulta-
neous parameter adjustmentÓ on page 20.
+Selecting the way in which internal effect units are used
Option à  Effect à Effect Pattern Ñ choose an effect pattern which 
to match your requirements (see ÒSelecting effect patternsÓ on page 24).
+Selecting and assigning the AUX and EFFECT RETURN 
controls
Option à Setup à Aux Rtn Input/AssignÑchoose the source and 
the routing of the aux and effect returns.
TASCAM 
TM-D1000
 O
PERATIONAL
 Q
UICK
 R
EFERENCE
 G
UIDE
+Assigning the channels which use dynamic processors
Option à Effect à Ch Dynamics InsertÑpush the DATA ENTRY 
knob to toggle the dynamics on and off, and turn it to move the cursor (see ÒAssigning 
channel dynamicsÓ on page 19).
+Setting the dynamic processor parameters
Press the PARAM SEL key until the EFFECT/DYNAMICS indicator lights green, press the 
CH SEL key of one of the channels using dynamic processors, and use the data editing 
knobs to set the processor parameters (see ÒAssigning channel dynamicsÓ on page 19).
+Setting AUX send levels
Press the PARAM SEL key until the AUX indicator lights green, and use the data editing 
knobs to set the levels (see ÒSetting aux send levelsÓ on page 24).
+Selecting the effect to use
Press the PARAM SEL key until the EFFECT/DYNAMICS key lights green, and use the 
DATA ENTRY knob to select the effect type (see ÒSelecting the effect to useÓ on page 24).
+Editing the effect parameters
After selecting the effect as described above, use the data editing knobs to set the parame-
ters.
+Recalling a snapshot
Press the ESCAPE/RECALL key until the display shows  RECALL?. Choose the snap-
shot and press 
ENTER (see ÒRecalling snapshotsÓ on page 26).
+Storing a snapshot
Press and hold the SHIFT key and press the STORE (ESCAPE/RECALL) key. Choose a 
memory, and press 
ENTER (see ÒStoring a snapshotÓ on page 26).
+Setting the MMC ID of the TM-D1000
Option à MIDI à MMC Device ID (see ÒSetting up the device IDsÓ on page 
29).
+Controlling an external device though MMC
Press and hold down the SHIFT key while pressing the MMC control keys (MMC blue 
labels below the keys)Ñsee ÒMIDI Machine controlÓ on page 29.
+Selecting the MTC type for location operations
Option à MIDI à MTC Type (see ÒSelecting the MTC typeÓ on page 30).
+Storing and locating to location memories
Use the MEMO key (see ÒLocationsÓ on page 30).
+Setting MIDI channels to control the TM-D1000 (Program 
Change)
Option à MIDI à MIDI Ch Select for the Mixer, Effects, Dynamics (see 
ÒSetting Program Change receive channelsÓ on page 32). 
						

							Factory default settings
+MODE menu
+Setup menu
+Effect menu
+MIDI menu
+System Menu
MODE selectMIX
Buss Function Select
ST+4Aux[Mono]
 (MIX) / 
ST+4Grp
 (REC)
All Ch Aux Pre/Postpost
Solo mode
PFL (In-Place SOLO) 
 (REC) / 
In-place SOLO(PFL) (MIX)
Digital InputA:RCA
Digital Out
(A:B) L-R:1-2
Digital Out FormatA:SPDIF / B:SPDIF
Direct out mode Post Input Fader
Effect Rtn Input/
AssignInput:Effect2 / Assign:L-R
Aux Rtn Input/Assign
Input:Digital In A 
 / 
Assign:L-R
Ch7-8 Route TargetAnalog In
Ch1-8 Input Analog In
Ch9-16 InputTDIF-1A
TDIF-1A Direct Out Ch1-8
Effect PatternCh Dynamics (REC) / 
L-R:Effect1 Aux1-
2:Effect2
  (MIX)
Ch Dynamics Insert
1234 to channels 1234
MIDI Ch SelectMixer=1, Effectors 1=2 & 2=3 
and 
Dynamics 1 through 4 disabled
MTC Type 30NDF
MMC Device ID1
MMC Communication Closed-loop
Control Change DefeatREC Mode:No / MIX Mode:Yes
L-R/GRP Control 
ChangeNo. 9
Master Clock SelectInternal [48k ]
Direct Recall Defeat Yes
REMOTE CONT FunctionSnapshot Change [ up ]
TDIF-1 A/B Word Length A:24bit
Meter AdjustReleaseTime:30ms / 
 
Hold Time:0s
TASCAM 
TM-D1000
 O
PERATIONAL
 Q
UICK
 R
EFERENCE
 G
UIDE
TASCAM TM-D1000 Digital Mixer
Connections for your first recording session
DIGITAL OUT A
AES/EBU  or
SPDIF
digital
output
MONITOR 
OUTPUT 
 (L and R)DIGITAL IN
DIGITAL IN  A
assigned to  two 
input channels)DIGITAL OUT
AES/EBU 
or SPDIF
Balanced 
+4 dBu 
inputs
DIGITAL IN B
(option)
assigned to
7&8AUX SENDS 
(1-2 or 3-4)
MIDI OUT MIDI IN
MIDI IN MIDI OUTTDIF-1 A
TDIF-1
REMOTE IN/SYNC IN
REMOTE OUT
DA-38 DTRS recorder 
controlled by MMC MMC-38 MIDI 
Interface con-
trollerTM-D1000 Digital MixerMonitoring system
DAT mastering recorder Multi-effector 
with digital 
output
MIC (1/4) XLR 
(balanced)