Tascam Digital Mixing Console TM-D4000 Owners Manual

 
13 - Rear panel & connections—Analog outputs, etc. 
13–2  
[54] PHANTOM (+48V) 1–4 & 5–8 
switches 
When turned on, these switches provide +48 V phan-
tom powering to the XLR-type  
MIC 
 connectors  
[47] 
 
on the eight integral analog input channels, for pow-
ering condenser microphones. 
WARNING 
Make sure that these switches are not turned 
on if equipment which does not require phan-
tom power is connected to these jacks, and if  
the  
MIC 
 input is selected  
[50] 
. 
[55] L (MONO) & R inputs...

 
13 - Rear panel & connections—Digital I/O 
 13–3 
[62] 2TR RTN 1/2 switch 
This switch is used to select which of the 2-track 
mastering recorder inputs ( 
[57] 
 and  
[58] 
) is used 
when the  
2TR 
 monitor select key  
[22] 
 is active.
When this switch is pressed in, the balanced XLR-
type inputs are active, and when out, the unbalanced 
RCA inputs are active. 
[63] CR LEVEL 
This is used to control the level of the signal selected 
using the monitor select keys  
[22] 
 sent through the 
pair of...

13 - Rear panel & connections—Other connections
13–4 
This stereo signal may be routed to any combination 
of the following: input channels 5-6, input channels 
13-14 and 
ST-IN 1, using the I/O SETUP 
screen accessed through the 
DIGITAL I/O key (see 
3.1, “I/O setup”).
Regardless of the channel assignment, the signal 
received here may always be selected for monitoring 
using the 
D-IN 1 key of the monitor select keys [22].
Using the 
DIGITAL I/O screens, this may 
also be used as a clock source.
13.5...

 
14–1 
14 - Specifications, etc. 
This section provides technical details relating to the 
TM-D4000.
All specifications are given with the factory reference 
level of –16 dBFS. This can be changed to either 
–20 dBFS or –9 dBFS by a qualified service person, 
affecting the maximum output level (0 dBFS)
Changes in specifications and features may be made 
without notice or obligation. 
14.1 Analog audio I/O 
14.2 Digital audio I/O 
For details of the I/O facilities provided by the inter-
face cards, please...

 
14 - Specifications, etc. 
14–2 
14.4 Analog performance 
14.4.1 MIC/LINE channel inputs 
(measured with STEREO 
OUTPUTS)
14.4.2 STEREO IN 1 and 2 (measured 
with STEREO OUTPUTS)
14.4.3 2TR RTN1 input
14.4.4 2TR RTN2 input
14.4.5 STEREO outputs (XLR)14.4.6 STEREO outputs (RCA)
14.4.7 AUX 1–6 outputs
14.4.8 CR outputs
14.4.9 STUDIO outputs
14.4.10 PHONES output
14.4.11 Overall system performance 
CASCADE IN/
OUT 
25-pin ’D’-sub connector
 
TO METER 
37-pin ’D’-sub connector for connection to 
optional...

 
14 - Specifications, etc. 
14–3 
14.5 Physical specifications 
14.6 Error and warning messages 
Not every one of these messages indicates an error. 
The purpose of some of these messages is to let you 
know that the status of some of the parameters of the 
TM-D4000 have changed.
“User” messages, i.e. those which result from an 
invalid entry or selection, are marked with a  
l 
.
“Confirm” messages, where a response may be nec-
essary to confirm an action or setting, are marked by 
a  
4 
.
“Fatal”...

14 - Specifications, etc.
14–4
14.6.3 Automation setup
14.6.4 Machine control
14.6.5 Snapshot library
In these messages, XX represents the snapshot 
library entry number
l
TM-D4000 
Firmware Version 
Panel :x.xx Main 
y.yy Remote z.zz
The main, display and 
machine control version 
numbers (major and minor 
revisions) of the software 
currently installed in the 
TM-D4000
8
 
Battery Voltage 
is Too Low to 
Save T-D4000 
Data
Contact TASCAM service 
for the internal battery to 
be replaced. If you cannot...

14 - Specifications, etc.
14–5
14.6.6 Dynamics library
In these messages, XX represents the library 
entry, and 
YY represents the channel(s) using 
the dynamics processor settings.
14.6.7 EQ library
In these messages, XX represents the library 
entry, and 
YY represents the channel(s) using 
the EQ setting.14.6.8 Effect library
In these messages, XX represents the library 
entry.
14.6.9 Stereo link (using SEL keys)
14.6.10 Computer communications 
(automation) l
DYN LibraryXX is 
Read Only!An attempt...

14 - Specifications, etc.
14–6
14.6.11 MIDI14.6.12 Fatal System Errors
NOTE
These messages should not occur. However, 
if you do see such a message, please make a 
note of the number displayed, and contact 
TASCAM Service. Inform them of the error 
and, if possible, a brief description of your 
system and the events leading up to the error. 
No recovery is possible from these errors—
you must turn down the level of the monitoring 
system, power down the TM-D4000 and wait 
a few seconds before switching...

14 - Specifications, etc.
14–7
14.7 Block diagram