Tascam DA 88_quick Start Guide
Here you can view all the pages of manual Tascam DA 88_quick Start Guide. The Tascam manuals for Cassette Player are available online for free. You can easily download all the documents as PDF.
Page 1
1 DA-88 QUICK TIPS (VERSION 4 SOFTWARE) ABS / TC DISPLAY MODE SWITCHING (REQUIRES SY-88) 1) Hold DISPLAY and press UP to enter ABS display 2) Hold DISPLAY and press DOWN to enter TC mode ABS / TC REFERENCE SWITCHING (REQUIRES SY-88) 1) Default is ABS Time 2) With DISPLAY set to ABS, press both UP and DOWN, then press either UP or DOWN to toggle between ABS and TC 3) Press DISPLAY to exit AUTO PLAY FUNCTION 1) After either MEMO 1 or MEMO 2 have been captured 2) Enable AUTO PLAY 3) Press either LOC 1 or...
Page 2
2 BEGINNING OF TAPE PLAY 1) Hold REW, FF and PLAY while powering On BEGINNING OF TAPE STOP 1) Hold FF and PLAY while powering On CHASE LOCK SYNCHRONIZATION (CODE ONLY MASTER) (Requires SY-88) [Dip-switch settings] 1) In a post environment, all dip-switches would typically be set to the DOWN position, unless the VIDEO THRU jack is used, in which case dip-switch S1 #1 would be UP. 2) If a composer is running virtual MIDI tracks in sync with the DA-88 while slaved to TC, place dip-switch S1 #2 in the...
Page 3
3 350 to 400 hours: Perform manual cleaning of heads and guides. Check tape path alignment after cleaning. (requires proper test and measurement equipment, and should be performed by qualified service personnel) During third cleaning, (1000 hours) a complete alignment check is suggested. Remember, the duration between cleanings may vary depending on your environment. A dusty or smokey environment will shorten the cleaning cycle. Although most name brand tapes are of very high quality, it is possible...
Page 4
4 Note: Make certain that the Master tape is write protected. 6) Engage all REC FUNCTION switches on the Target DA-88 so as to arm all tracks Note: If dubbing Time Code, engage the TC REC FUNCTION switch, but DO NOT start the generator. 7) On Target DA-88, engage CHASE so that it locates to the same time position as the Source DA-88 8) On Target DA-88, engage DIGITAL IN 9) On Source DA-88, hold RECORD and press PLAY END OF TAPE REWIND 1) Hold REW, STOP and PLAY while powering On END OF TAPE STOP 1)...
Page 5
5 GREETING AT POWER ON The DA-88 can be programmed to display a greeting different from the scrolling TASCAM at Power ON. 1) Power ON holding FFWD, STOP, and PLAY 2) Press STOP before TASCAM begins scrolling to enter Test Mode (display will show TEST) 3) From the ABS display mode, IN sequence, press and hold the following keys: A. UP key B. DOWN key C. DISPLAY D. REMOTE - the character A should now appear - use the UP and DOWN keys to define letters 4) Enter the greeting, pressing DISPLAY after each...
Page 6
6 PEAK HOLD OFF 1) Hold REW, PLAY and REC while powering the unit On PREROLL - DEFAULT TIME: 5 SEC 1) To access, either RHSL or AUTO IN/OUT must be active 2) In the ABS display mode, press the DOWN key while holding the UP key 3) Edit value using UP and DOWN keys (minimum value = 5 sec.) REPEAT FUNCTION 1) After MEMO 1 and MEMO 2 have been captured 2) Press REPEAT - DA-88 automatically begins to cycle between these two Locate points, regardless of current tape position TIMECODE GENERATE (REQUIRES SY-88)...
Page 7
7 TRIM A CAPTURED LOCATE MEMORY (MEMO 1 & 2) 1) Capture the memory point via normal procedure 2) Recall that point via the DISPLAY key 3) Trim the address via UP / DOWN keys VARISPEED 1)± 6% 2) Press Vari Speed button 3) Use UP/ DOWN keys to adjust ã1997 TEAC America, Inc. 7733 Telegraph Road, Montebello, CA 90640 (213) 726-0303 FAXBACK Index #1130 (5/97)