Studio Experience Projector Matinee 1hd User Manual

31
Computer Input / (RGB Scart 21-Pin Video Input)
Input Source Selection (Menu Operation)
Press the MENU button, and the main menu appears.  Select
the Input Source Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
Choose Computer with the POINT UP/DOWN  button and press
the POINT RIGHT button.  The Source selection menu appears.   
1
2
Input Source Selection menu
Input Source Selection  menu 
Input Source Selection (Direct Operation)
You can...

32
Computer Input
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, or SXGA in most cases
(refer to “Compatible Computer System” on the next page).  When selecting Computer, this projector automatically tunes to
incoming signal and projects proper image without any special settings. 
The projector displays one of the Auto, - - -, Mode 1/2/3/4/5, or the system provided in the projector.
When the projector cannot recognize the connected
system as computer...

33
Computer Input
Compatible Computer System
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100
MHz of Dot Clock.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
MAC 211152 x...

34
Computer Input
Computer Adjustment (Auto) (Menu Operation)
The Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to
conform to your computer.  The Auto PC Adjustment function can be operated as follows.
Press the MENU button, and the main menu appears.  Select
the Computer Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Choose the Auto PC Adj., and then press the SELECT button...

35
Computer Input
Computer Adjustment (Manual)
This projector can automatically tune to the display signals from most personal computers currently distributed.  However,
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-
Scan system of this projector.  If this happens, the projector cannot reproduce a proper image and the image may be
recognized as a flickering picture, a non-synchronized picture, a non-centered picture, or a skewed...

36
Computer Input
To store adjustment data.
To clear adjustment data.Choose one of the positions from the Mode 1 to 5 where you
want to store with the POINT UP/DOWN button, and press the
SELECT button.  Select Yes with the SELECT button and
close the menu by pressing the SELECT button at the Quit.  
4
Adjust an image as necessary to eliminate flicker from the display.  Press the POINT LEFT/RIGHT button to adjust
value.(From 0 to 31.)
Fine sync
The number of total dots in one horizontal period.  Press the...

37
Computer Input
Adjustment of horizontal area displayed by the projector.  Press the POINT LEFT/RIGHT button to decrease/increase value
to match the resolution of image.
Display area H
Adjustment of vertical area displayed by the projector.  Press the POINT LEFT/RIGHT button to decrease/increase value to
match the resolution of image.
Display area V
When this function is on, SXGA image is fully displayed at 4 : 3 aspect ratio.  It is displayed at 5 : 4 aspect ratio with this
function off.  
Full...

38
Computer Input
Image Level Selection (Menu Operation)
Press the MENU button, and the main menu appears.  Select
the Image Level Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Choose the level that you want to set with the POINT UP/DOWN
button, and then press the SELECT button to activate it.
Image Level Selection menu
Normal picture adjustment preset on this projector.
Standard
Picture adjustment improved in reproduction of halftones....

39
Computer Input
Press the MENU button, and the main menu appears.  Select
the Image Level Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Choose the item that you want to adjust with the POINT
UP/DOWN button, and then press the POINT LEFT/RIGHT
button to adjust each item.  The items displayed in a line can be
adjusted while you see the change of the image.  Press the
SELECT button to finish adjusting an item.  The on-screen menu
returns to...

40
Computer Input
Press the POINT LEFT button to decrease contrast and the POINT RIGHT button to increase contrast.  (From 0 to 63.)
Press the POINT LEFT button to adjust image darker and the POINT RIGHT button to adjust image brighter.  (From 0 to 63.)
Contrast
Brightness
Press the POINT LEFT button or the POINT RIGHT button to obtain better balance of contrast.  (From 0 to 15.)
Gamma
Press the POINT LEFT button to soften the image and the POINT RIGHT button to sharpen the image.  (From 0 to 15.)...