Stihl Fs 410 C Instruction Manual
Here you can view all the pages of manual Stihl Fs 410 C Instruction Manual. The Stihl manuals for Brush Cutter are available online for free. You can easily download all the documents as PDF.
Page 21
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 19 WARNING Deflector (3) is approved for shredder blades only and must therefore be mounted before fitting a shredder blade. WARNING The limit stop (4) is approved as a deflector for circular saw blades only and must therefore be mounted before fitting a circular saw blade. It is also necessary to change the guard ring (5), see "Mounting the Cutting Attachment" / "Mounting Circular Saw Blades". Mounting the Deflector...
Page 22
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 20 Guard ring for mowing applications Always fit guard ring (1) when using –mowing heads –grass cutting blades –brush knives –shredder blades to ensure optimum protection against grass cuttings. Guard ring for sawing applications Fit guard ring (4) only when you use circular saw blades.Mounting the Thrust Plate and Guard Washer NFit the thrust plate (1) and guard washer (2) on the shaft (3). NOTICE The thrust plate (1) on the gearbox is...
Page 23
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 21 NPull the guard washer (1) and thrust plate (2) off the shaft. NThoroughly clean the guard ring, shaft, thrust plate and guard washer – do not remove the guard ring. Blocking the Shaft The output shaft (1) must be blocked with the stop pin (2) to mount or remove cutting attachments. The stop pin is included with the machine and is available as a special accessory. NInsert the stop pin (2) in the bore (3) in the gearbox as far as stop,...
Page 24
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 22 Check direction of rotation of cutting attachment Cutting attachments 1, 4 and 5 may be mounted either way round – they must be turned over regularly to help avoid one-sided wear. The cutting edges of cutting attachments 2 and 3 must point clockwise. NUse guard ring for mowing attachments.NPlace the cutting attachment (1) in position. WARNING Collar (a) must locate in the cutting attachment's mounting hole (b). Securing the cutting...
Page 25
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 23 NPlace the shredder blade (1) in position – the cutting edges must point upwards. WARNING Collar (a) must locate in the cutting attachment's mounting hole (b). Securing the cutting attachment NFit the thrust washer (2) – convex side must face up. NFit the shredder blade guard ring (3) – opening must face up. NBlock the shaft. NFit the nut (4) counterclockwise and tighten it down firmly. WARNING If the mounting nut has become too loose,...
Page 26
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 24 Check direction of rotation of cutting attachment Cutting edges of circular saw blades must point clockwise. NPlace the cutting attachment (1) in position. WARNING Collar (a) must locate in the cutting attachment's mounting hole (b).Securing the cutting attachment NFit the thrust washer (2) – convex side must face up. NFit the rider plate (3). A rider plate (3) for sawing applications is available as a special accessory. It allows the...
Page 27
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 25 If your machine is equipped with a catalytic converter, you must use unleaded gasoline. NOTICE A few tankfuls of leaded gasoline will greatly reduce the efficiency of the catalytic converter. Gasoline with an ethanol content of more than 10% can cause running problems in engines with a manually adjustable carburetor and should not be used in such engines. Engines equipped with M-Tronic deliver full power when run on gasoline with an...
Page 28
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 26 Fuel Filler Cap WARNING When fueling on a slope, always position the machine with the filler cap facing uphill. NPlace the machine on level ground so that the filler cap is facing up. NBefore fueling, clean the filler cap and the area around it to ensure that no dirt falls into the tank. Opening the filler cap NTurn the cap counterclockwise until it can be removed from the tank opening. NRemove the cap. Filling Up with Fuel Take care not to...
Page 29
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 27 Attaching Machine to Harness NAttach the carabiner (1) to the perforated rail (2) on the drive tube. Disconnecting Machine from Harness NPress down the bar on the carabiner (1) and pull the perforated rail (2) out of the carabiner.The machine will balance differently depending on the cutting attachment mounted. NLet the machine swing on the harness until it stops moving – change the connection point if necessary Hanging positions Mowing...
Page 30
FS 360 C-M, FS 410 C-M, FS 460 C-M, FS 490 C-M English 28 Controls 1Throttle trigger lockout 2Throttle trigger 3Stop switch with Run and Stop positions. Press the momentary contact stop switch to switch off the ignition. Function of stop switch and ignition system The stop switch is normally in the Run position, i.e. when it is not depressed: The ignition is switched on – the engine is ready to start. Operate the stop switch to switch off the ignition. The ignition is switched on again...