Stihl 201 Tcm Manual

MS 201 TC-M
English
9 The condition of the anti-vibration 
elements influences vibration behaviour 
– inspect anti-vibration elements 
periodically.
Inspect chain catcher – replace if 
damaged.
Switch off the engine
–To check the chain tension
–To retension the chain
–To replace the chain
–For remedying malfunctions
Observe sharpening instructions – for 
safe and proper handling, always keep 
the chain and guide bar in flawless 
condition. Keep the chain properly 
sharpened, tensioned and well...

MS 201 TC-M
English
10 –Do not cut with the bar nose.
–Take special care with small, tough 
limbs, they may catch the chain.
–Never cut several limbs at once.
–Do not overreach.
–Never cut above shoulder height.
–Use extreme caution when re-
entering a previous cut.
–Do not attempt plunge cuts if you 
are not experienced in this cutting 
technique.
–Be alert for shifting of the log or 
other forces that may cause the cut 
to close and pinch the chain.
–Always cut with a correctly 
sharpened, properly...

MS 201 TC-M
English
11 If conditions allow, work from a lift 
bucket.
Never work on a ladder or on any other 
insecure support, do not work above 
shoulder height.
Cordon off the work area in order to 
reduce the risk of injuries and damage to 
property from falling branches (e.g. 
motor vehicles).
When working with a lifeline there is a 
risk of cutting through the rope – to 
reduce the risk of fall injuries, always 
use double lifelines.
Take special care when cutting through 
a limb. Hold the machine...

MS 201 TC-M
English
12 A cutting attachment consists of the saw 
chain, guide bar and chain sprocket.
The cutting attachment that comes 
standard is designed to exactly match 
the chain saw.
–The pitch (t) of the saw chain (1), 
chain sprocket and the nose 
sprocket of the Rollomatic guide bar 
must match.
–The drive link gauge (2) of the saw 
chain (1) must match the groove 
width of the guide bar (3).
If non-matching components are used, 
the cutting attachment may be damaged 
beyond repair after a...

MS 201 TC-M
English
13 NFit chain around the sprocket (1) 
and over the guide bar – the cutting 
edges on top of the bar must point to 
the bar nose.
NTurn the screw (2) clockwise until 
there is very little chain sag on the 
underside of the bar – and the drive 
link tangs are engaged in the bar 
groove.NRefit the chain sprocket cover – 
the pivot pin on the hand guard must 
engage the sleeve – and then screw 
the nut onto the stud finger-tight.
NGo to chapter on "Tensioning the 
Saw...

MS 201 TC-M
English
14 NShut off the engine.
NWear work gloves to protect your 
hands.
NThe chain must fit snugly against 
the underside of the bar and it must 
still be possible to pull the chain 
along the bar by hand when the 
chain brake is released.
NIf necessary, retension the chain.
A new chain has to be retensioned more 
often than one that has been in use for 
some time.
NCheck chain tension frequently – 
see chapter on "Operating 
Instructions".Your engine requires a mixture of...

MS 201 TC-M
English
15 Examples
NUse a canister approved for storing 
fuel. Pour oil into canister first, then 
add gasoline and mix thoroughly.
Storing Fuel
Store fuel only in approved safety-type 
fuel canisters in a dry, cool and safe 
location protected from light and the sun.
Fuel mix ages – only mix sufficient fuel 
for a few weeks work. Do not store fuel 
mix for longer than 30 days. Exposure to 
light, the sun, low or high temperatures 
can quickly make the fuel mix unusable.
STIHL MotoMix may be...

MS 201 TC-M
English
16 NTurn the cap counterclockwise 
(about a quarter turn).
Marks on tank cap and fuel tank must 
line up.
NRemove the cap.
Filling up with fuel
Take care not to spill fuel while fueling 
and do not overfill the tank.
STIHL recommends you use the STIHL 
filler nozzle for fuel (special accessory).
NFill up with fuel.
Closing
Grip must be vertical:
NFit the cap – marks on tank cap and 
fuel tank must line up.
NPress the cap down as far as stop.
NWhile holding the cap depressed, 
turn it...

MS 201 TC-M
English
17 NPlace the cap on the opening and 
rotate it counterclockwise until it 
engages the filler neck.
NContinue rotating the cap 
counterclockwise (about a quarter 
turn) – this causes the bottom of the 
cap to be turned to the correct 
position.
NTurn the cap clockwise and lock it in 
position – see section on "Closing".For automatic and reliable lubrication of 
the chain and guide bar – use only an 
environmentally compatible quality 
chain and bar lubricant. Rapidly...

MS 201 TC-M
English
18 If the oil tank is still partly full, the reason 
may be a problem in the oil supply 
system: Check chain lubrication, clean 
the oil passages, contact your servicing 
dealer for assistance if necessary. 
STIHL recommends that maintenance 
and repair work be carried out only by 
authorized STIHL dealers.
The saw chain must always throw off a 
small amount of oil.
NOTICE
Never operate your saw without chain 
lubrication. If the chain runs dry, the 
whole cutting attachment will be...