Steinberg UR28M Operation Manual

EN
DE
FR
ES
JA
USB AUDIO INTERFACE
IT 

UR28M  Operation Manual2
Contents
Introduction.................. ..........................................3
Contents in this Operation Manu al............................... 3
Features .............. ............................................ ............. 3
Panel Controls and Term inals (Details)...............4
Rear Panel....................................................... ............. 4
Front Panel ......................................................... .......... 5
Panel Controls for the...

Introduction
UR28M  Operation Manual3
Introduction
Contents in this Operation 
Manual
This Operation Manual explains how to use the 
device. The explanations in this manual assume that 
you’ve set up the device and prepared it for use 
according to the included Getting Started 
document. If you haven’t done that yet, refer to the 
Getting Started document and complete the setup 
before reading this manual.
Features
High-resolution Microphone 
Preamplifiers (D-Pre) 
Discrete microphone preamps featuring a...

Panel Controls and Terminals (Details)
UR28M  Operation Manual4
Panel Controls and 
Terminals (Details)
Rear Panel
DC IN 12V
For connection to the AC power adaptor.
 Grounding screw
For connection to a ground wire.
If you have a problem with hum or noise, use this 
terminal to connect to ground. The noise may be 
reduced.
 2TR IN (3.5 mm, stereo)
For connection to a portable audio player.
The input signal at 2TR IN flows only to MIX 1 
(page 27), and not to the computer.
 USB2.0 (USB port)
For...

Panel Controls and Terminals (Details)
UR28M  Operation Manual5
Front Panel
HI-Z switch
Turns on (0 ) and off (/) the HI-Z of the MIC/
LINE/HI-Z.
Turn this switch on when connecting high 
impedance instruments, such as an electric 
guitar or electric bass, directly to the MIC/LINE/
HI-Z.
When you turn this switch on, use an unbalanced 
phone cable for connection between the 
instruments and the MIC/LINE/HI-Z. If you use a 
balanced cable or an XLR  cable, this device will 
not work correctly.
CAUTION
•...

Panel Controls and Terminals (Details)
UR28M  Operation Manual6
• When turning phantom power ON, make sure that no 
equipment other than phantom-powered devices 
such as condenser microphones are connected. 
Devices other than conden ser microphones may be 
damaged if connected to the phantom power supply. 
Note, however, that the switch may be left on when 
connecting to balanced dynamic microphones. When 
connecting an unbalanced de vice to the MIC/LINE/HI-
Z 1/2 and phantom power is turned on, hum or...

Panel Controls and Terminals (Details)
UR28M  Operation Manual7
!MIX 1–3 lamp
For Alternate mode, this indicates the output 
signal (MIX 1–3) of the LINE OUTPUT.
For Independent mode, this indicates the output 
signal (MIX 1–3) of the LINE OUTPUT selected by 
OUTPUT buttons A–C.
For details on the mode, including how to select 
the mode, refer to the “Setup Window” (page 14) 
in the section “dspMixFx UR28M” or the “Master 
Levels Window” (page 19) in the section 
“Dedicated Windows for Cubase Series.”
...

Panel Controls for the Software Programs
UR28M  Operation Manual8
Panel Controls for the 
Software Programs
Control Panel of the Audio 
Driver
This is the control panel for selecting the general 
settings of the audio driver. Click the upper tabs to 
select the desired window.
Screenshot
How to Open the Window
Windows
•[Start]  [Control Panel]   [Hardware and Sound] 
or [Sounds, Speech, and Audio Devices]   
[Yamaha Steinberg USB Driver]
• From the Cubase series menu, [Devices]   [Device Setup]  ...

Panel Controls for the Software Programs
UR28M  Operation Manual9
ASIO Window (Windows only)
This is the window for selecting the ASIO driver 
settings.
Device
Selects the device that  will be using the ASIO 
driver. This function is available when connecting 
to the computer two or more devices compatible 
with the Yamaha Steinberg USB Driver.
 Buffer Size
Selects the buffer size (page 27) for the ASIO 
driver. The range varies depending on the sample 
rate.
NOTE
For Mac, select the buffer size in the...

Panel Controls for the Software Programs
UR28M  Operation Manual10
How to Open the Window
Windows
[Start]  [All Programs]   [Steinberg UR28M]   
[dspMixFx UR28M]
Mac
[Macintosh HD]   [Applications]   [dspMixFx 
UR28M]
Panel Controls
To o l  A r e a
This is the area for configuring the common settings 
of the dspMixFx UR28M.
 Quit
Quits the dspMixFx UR28M.
 Minimize
Minimizes the dspMixFx UR28M window.
 Menu
Provides four menus, including Save the settings 
file of the dspMixFx UR28M (page 27) and...