Star .32 Auto Instructions Manual

							i’
RECESS
SLIDE SLIDE 
STOP REAR END OF SLIDE STOP
10
Fig. 5 
						

							BARREL LINK 
						

							12
8
Fig, 7 
						

							Fig. 8
13 
						

							IMPORTANT INSTRUCTIONS FOR BEST PERFORMANCE OF THE PISTOLS
1. All moving parts should be  lightly  oiled.
2.  Clean the barrel and chamber after firing. The barrel and chamber should\
 be cleaned
from the breech   avoid cleaning from the muzzle. Always wipe off the exterior of the
pistol after use with a slightly oily cloth to protect the finish.
3.       Use only standard loads for which the pistol is designed and make sure that the bore is free from obstructions before loading and shooting.
4.        Care should be taken to prevent the magazine from being dented or otherwise damaged.
NOTE: DO NOT POINT THE PISTOL, LOADED OR UNLOADED, AT ANYTHING YOU DO NOT WANT TO SHOOT.
COMPLETE DISASSEMBLY OF THE PISTOL
Follow the same procedure as by disassembly for cleaning purposes.
Note: All the pins are removed from left to right, except the trigger pin which com\
es out to the left.
Remove grips (95 & 96b) unscrewing the four screws (97).
 Holding the pistol in the left hand, depress the magazine catch button (29) with the
index finger of the same hand far enough inwards to permit the catch loc\
k (28) to be
turned to the left by means of the cleaning rod. The complete magazine c\
atch assembly
may now be removed from the frame. 
						

							Remove pin (20) from the trigger (19) and both pieces will come out \
without difficutly,
together with the sear bar (23) and interrupter (25), when pulling it downw ards.
To remove the sear bar (23) from the trigger (19), push the sear bar pin out, thus
freeing it as well as the trigger plunger (22) and its spring (21).
Remove sear pin 
(15) and this will free the sear spring (16).
Using a copper or brass punch, drive out the hammer pin (11) from right to left from
the hammer (06). This releases both the spring  (09)  and plunger (10).
Withdraw the thumb safety (36), grasping the thumb piece and turning to the right,
lift it up. Care should be taken to let the plunger (38) and its spring (39) jum\
p away when
released.
The slide stop (41) has a pin which when removed frees the retaining p\
lunger and its
spring.
The extractor (66) may now be removed, pushing the pin (67) from bel\
ow upwards.
This frees the spring (69).
Remove the rear sight (74) from right to left, drifting slightly with \
a copper punch.
Push the retaining pin (71) of the firing pin (70) upwards from the \
slide and tilting the
slide release this piece and its spring (72).
TO REASSEMBLE THE PISTOL
Reverse the beforementioned procedure. 
						

							CHART OF POSSIBLE FIRING INTERRUPTIONS
CAUSES
1. Failure of feeding: May be due  to magazine not fully in-
serted into the grip or to magazine
dents.
a   Magazine blown.                        
2.
2. Failure to fire.
a  Defective cartridge which prevent com-
plete locking of the pistol.
b  Built-up residue in the firing chamber.
c  Firing Pin broken.
d  Defective cartridge primer.
3. Failure of extraction:
a  Cartridge has insufficient gas pressure,thus preventing complete backwardsstroke of the slide.
b  Cartridge head (rim) broken.
c  Defective extractor.
d  Cartridge or case remains pressed
between breechblock and chamber.
CORRECTIONS
1.
 Push the magazine completely into the
a Remove dent on magazine and if themagazine is  faulty, correct same.
a  Replace the cartridge.
b  Disassemble the pistol  and clean the
firing chamber thoroughly.
c   May be caused by excessive dry firing.
Replace firing pin.d 
 Remove defective cartridge.
3.
a  Remove cartridge case.
b  Remove cartridge case.
c  Replace the extractor.d  Draw the slide completely backwards
and while holding it back, push the
slide stop up to engage in the notch onthe slide. (Care should be taken toprevent any casualty while operating
with the gun). Remove  magazine and
withdraw cartridge or case. 
						

							“STAR“ PISTOL PARTS 
						

							COMPONENT PARTS OF THE “STAR” PISTOL
Part N.º
01 Frame with Ejector,
06 Hammer with Strut and Pin.
09 Hammer Spring.10 Hammer Spring Plunger.
11 Hammer Pin.
14 Sear.
15 Sear Pin.
16 Sear Spring.
19 Trigger.
20 Trigger Pin.
21 Trigger Plunger Spring,
22 Trigger Plunger.
23 Sear Bar.
25 Interrupter.
28 Magazine Catch Button.
29 Magazine Catch Lock.
30 Magazine Catch Lock Spring,
36 Safety thumb.
38 Safety Spring Plunger.
39 Safety Plunger Spring.
Part N.º
41  Slide Stop. 53  Magazine Tube with Floor Plate.
54  Magazine Follower.
56  Magazine Spring.61  Barrel with Link and Pin.
65  Slide with Front Sight.
66 Extractor. 
67 Extractor Pin.
69 Extractor Spring.
 
96  Grip, left.
97  Grip Screw
70   Firing Pin. 
71  Firing Pin Retainig Pin,
72  Firing Pin Spring.
74  Sight, rear. 78  Barrel Bushing.
80  Recoil Spring Guide.
83  Recoil Spring
84  Recoil Spring Plug.
92  Swivel.
 95.  Grip, right
FOR REPLACEMENT PARTS SEE THE DEALER WHO SOLD YOU THIS GUN. When ordering parts, please state model of pistol and  its serial number.