Sony Vpl Es2 Projector User Manual

11Location and Function of Controls
Overview
Location and 
Function of Controls 
  
1Control panel
For details, see “Control Panel” on 
page 12.
2Lens protector (lens cover)
The lens protector automatically opens 
when the power is turned on.
3Ventilation holes (exhaust)
4Remote control detector 
5Adjuster (hind pad)
Turn the adjuster to the right or left for 
minor tilt adjustment of the projected 
picture.
6Ventilation holes (intake)/Lamp 
cover
7Ventilation holes (intake)/air 
filter cover
 Do not...

12Location and Function of Controls
qdConnector panel
For details, see “Connector Panel” on 
page 13.
qfSpeaker
qgSecurity lock 
Connects to an optional security cable 
(Kensington’s).
Web page address: 
http://www.kensington.com/
1I / 1  (on/standby) key
Turns on the projector when the 
projector is in standby mode. The ON/
STANDBY indicator around the I / 1 
key lights in green when the power is 
turned on.
2ON/STANDBY indicator (located 
around the 
I / 1 key)
Lights up or flashes under the following...

13Location and Function of Controls
Overview
VPL-CS7
VPL-ES2
1INPUT A connector (HD D-sub 
15-pin, female)
Connect to external equipment such as a 
computer. 
Connects to the monitor output on a 
computer using the supplied cable. 
When inputting a component or 15k 
RGB signal, use an optional cable.
For details, see “To connect to a video 
GBR/component output connector” on 
page 18.
2Video input connector
Connect to external video equipment 
such as a VCR.VIDEO (phono type): Connects to 
the composite...

14Location and Function of Controls
1I / 1 (on/standby) key
2ENTER/arrow key (
v/V/b/B)
Press the center of the key to use 
ENTER.
3MENU key
4D ZOOM +/
– key
Enlarges the image at a desired location 
on the screen.
5Infrared transmitter
6FREEZE key
Used to freeze the picture projected. To 
cancel the freeze function, press the key 
again.
7INPUT key
8APA (Auto Pixel Alignment) key
Adjusts a picture clearest automatically 
while a signal is input from a computer.
For details, see “Smart APA” in the SET...

15Location and Function of Controls
Overview
Notes on Remote Commander 
operation
 Make sure that nothing obstructs the 
infrared beam between the Remote 
Commander and the remote control 
detector on the projector. Direct the 
Remote Commander toward the remote 
control detector.
 The operation range is limited. The shorter 
the distance between the Remote 
Commander and the remote control 
detector is, the wider the angle within 
which the commander can control the 
projector becomes.  

16Installing the Projector
BProjecting the Picture
Installing the Projector
This section describes how to install the projector.
The distance between the lens and the screen varies depending on the size of 
the screen. Use the following table as a guide. 
There may be a slight difference between the actual value and the design value shown 
in the table above.Unit: m (feet)
Screen size 
(inches)40 60 80 100 120 150 200 300
Minimum 
Distance1.1
(3.6)1.7
(5.6)2.3 
(7.5)2.9
(9.5)3.5
(11.5)4.4 
(14.4)5.9...

17Connecting the Projector
Projecting the Picture
Connecting the 
Projector
When you connect the projector, 
make sure to:
 Turn off all equipment before making any 
connections.
 Use the proper cables for each connection.
 Insert the cable plugs firmly; loose 
connections may increase noise and 
reduce performance of picture signals. 
When pulling out a cable, be sure to pull it 
out from the plug, not the cable itself
This section describes how to connect the 
projector to a computer.
For more...

18Connecting the Projector
To connect a Macintosh computer equipped 
with video output connector of a type having 
two rows of pins, use a commercially available 
plug adaptor.
  
This section describes how to connect the 
projector to a VCR. 
For more information, refer to the 
instruction manuals of the equipment you 
are connecting. 
To connect to a video or S video 
output connector
Ex. VPL-CS7
 
1Stereo audio connecting cable (not supplied) 
(Use a no-resistance cable)
2 Video cable (not supplied)...

19Projecting
Projecting the Picture
 
This section describes how to connect the 
projector to a monitor equipment. 
For more information, refer to the 
instruction manuals of the equipment you 
are connecting.
* This projector is not guaranteed for 
connecting more than 2 monitors in loop-
through connection.
Projecting
1Plug the AC power cord into a wall 
outlet, then connect all equipment.
The ON/STANDBY indicator lights in 
red and the projector goes into standby 
mode. 
2Press the I / 1 key.
The...

20Projecting
4Press the INPUT key to select the 
input source.
Each time you press the key, the input 
signal switches as follows:
 
Smart APA (Auto Pixel Alignment) 
adjusts the picture of the connected 
equipment so that it is projected clearly.
5Switch the equipment to be connected 
to output to the projector.
Depending on the type of your 
computer, for example a notebook, or an 
all-in-one LCD type, you may have to 
switch the computer to output to the 
projector by pressing certain keys 
(e.g., ,...