Sony Vaio Sony Vaio Vgnt Manual

							T Series
Confidential
HDD -2
5)1.MS-1-D.11
Remove the HDD.
HDD
To Type 
						

							T Series
Confidential
Parts of the HDD
1) 2)1.MS-1-D.12
Remove the Cushion (HDD) (four places).Disconnect the FPC.
*Use the tweezers and disconnect the connector portion little by little. 
* Be careful not to bend the pins.
Connector
Cushion (HDD)
FPC
To Type 
						

							T Series
Confidential
Memory
1.MS-1-D.131)
Outspread the tabs (arrow 1) and pull out the Memory 
obliquely upward (arrow 2).
1
1
2Tab
Memory
RemarkMemory is installed only in the following these models.
1st --- T90S, T90PS, T160P,T170P  
						

							T Series
Confidential
Wireless LAN Card
1.MS-1-D.141)
Outspread the tabs (arrow 1), and pull out the Wireless LAN Card
obliquely upward (in the direction of the arrow 2). 
1
1
2
Tab
Wireless LAN Card 
						

							T Series
Confidential
Optical Disc Drive, CNX-270 Board -1
1)1.MS-1-D.15
Screw: B10
Remove the one screw.
2)
Remove the CNX Board from the Escutcheon (Front) 
and disconnect the FPC.
*Pull out it in the direction of the arrow.Insert a thin tool into the hole of the Bezel and pull out the Tray.
3)
Tray
Hole
4)
CNX Board
FPC
Cushion
Peel off the Cushion.
Escutcheon (Front) 
						

							T Series
Confidential
Optical Disc Drive, CNX-270 Board -2
5)1.MS-1-D.16
Disconnect the connector and remove the Optical Disc Drive.Connector
Disconnect the Harness and remove the CNX Board.
Harness
Side B
6)
7)
Remove the five screws.
Screw: B11 
						

							T Series
Confidential
CNX-273 Board -1
1) 2)1.MS-1-D.173) 4)
Remove the one screw.
* The screw secures the CNX Board together with the lug terminal.
Screw: B10
Disconnect the Harness (three places) and the FPC (one place).
Harness
Peel off the Tape (Harness).
Harness
FPC
Remove the convex portion of the Sheet from the hole.
Tape (Harness)
Sheet
Convex
Hole 
						

							T Series
Confidential
CNX-273 Board -2
5)1.MS-1-D.18
Peel off the Kapton Tape and remove the CNX Board.
*There is the Modem Card on the rear.
6)
Disconnect the Harness.
Peel off the Tape (Harness) (two places).
Tape (Harness)
Peel off the Sheet.
Sheet
7)
Kapton Tape
8)
Harness
CNX Board 
						

							T Series
Confidential
Modem Card -1
1)1.MS-1-D.19Remark
Remove the one screw.
Screw: B9
Side B
Remove the screw while securing the Nut of the side A 
with the 4 mm socket wrench.
Nut
Side A
2)
Modem Card
Side B
Disconnect the Modem Card.
*There is the connector on the rear.
Connector
3)
Remove the Cushion.
Cushion 
						

							T Series
Confidential
Modem Card -2
1.MS-1-D.20Remark
The Stand is installed under the Modem Card.