Sony Vaio Sony Vaio Vgnsz Manual

SZ Series
Confidential
SWX-214 Board
1) 2)1.MS-1-D.10
Peel off the Tape (Harness). Disconnect the Harness.
4)
Disconnect the Harness.
3)
Remove the one screw, and then the SWX Board.
Tape (Harness)
Harness
Harness
SWX Board
SWX Board
Screw:B5 

SZ Series
Confidential
IFX-437 Board
3)1.MS-1-D.11
Pull out the FFC in the direction of the arrow.Pull out the FFC vertically and disconnect it.
2)
1)
Remove the one screw, and then the IFX Board.
IFX Board
FFC
IFX Board
Screw:B5
FFC
TPM Model 

SZ Series
Confidential
Reserve Battery
1)1.MS-1-D.12
Disconnect the Harness, and remove the Reserve Battery.
* The adhesive tape is attached on the bottom of it.
Reserve Battery
Harness 

SZ Series
Confidential
Wireless LAN Card
1) 2)1.MS-1-D.13
Peel off the Sheet (Paste Cable) (five places).
*Camera Model --- Six placesOther --- Five places
Wireless LAN Card
1
1
Move the tab (two places) in the direction of the arrow 1 to release the 
lock, and pull out the Wireless LAN Card diagonally upward (arrow2).
2
Wireless LAN Card
Coaxial Cable
3)
Disconnect the coaxial cable (two places). 
* Pull out it  vertically.
Camera Model
1
[COR]
1
[CHG] 

SZ Series
Confidential
IFX-442 Board
1)1.MS-1-D.14
2)
Remove the screw, and remove the IFX Board while releasing it from 
the Escutcheon (L).
IFX Board
Escutcheon (L)
Coaxial Cable
Disconnect the coaxial cable. 
* Pull out it vertically.
Screw:B5
Bluetooth Model 

SZ Series
Confidential
LCD -1
1)
3)1.MS-1-D.15
Remove the one screw. 
* It secures the Lug Terminal.
Disconnect the Harness (LCD).
2)
4)
Lug Terminal
Harness (LCD)
Screw:B13
Camera Model
Disconnect the Harness (Microphone).
Harness (Microphone)
Peel off the Sheet (Paste Cable).
3
[ADD]
Sheet (Paste Cable) 
Harness (LCD) 

SZ Series
Confidential
LCD -2
5)1.MS-1-D.16
Screw:B8
Remove the four screws, and then the LCD.
LCD
6)
Harness (Camera)
Disconnect the Harness (Camera).
Camera Model
Camera Model
Peel off the Tape (Harness).
Tape (Harness)
7) 

SZ Series
Confidential
Cap (Hinge), Speaker (R)
1.MS-1-D.171) 2)
Disconnect the Harness, and remove the Speaker (R).
Harness
Speaker (R)
Cap (Hinge)
No WAN Model5
[ADD]
Remove the Cap (Hinge) .
*WAN Model --- One place No WAN Model --- Two places 

SZ Series
Confidential
Bluetooth Module
1.MS-1-D.181) 2)
Remove the Bluetooth Module.
Disconnect the coaxial cable. 
* Pull out it vertically.
Coaxial Cable
Bluetooth Module
Bluetooth Model
Connector
Bluetooth Module
3) 4)
Peel off the Tape (Harness).
Tape (Harness)
Peel off the Sheet (Paste Cable).
8[CHG]Sheet (Paste Cable)  

SZ Series
Confidential
ANL-66 Board -1
1)1.MS-1-D.19
2)
Remove the two screws.
Raise the lock lever to release the lock, and disconnect the FPC.
3)
FPC
4)
Screw:B2
Disconnect the FFC.
*A: Pull out it vertically upward.B: Pull out it in the direction of the arrow. A
B
FFC
Disconnect the Harness, and release it from the notch.
Notch
Harness