Sony Vaio Sony Vaio Vgnsz Manual

SZ Series
Confidential
Chapter 1. Disassembly & Assembly Guide
1.MS-1-D.1
1-3. Disassembly & Assembly
- Main Section -MS-1  Main Section Disassembly 

SZ Series
Confidential
Battery Pack, Dummy Card (EXP), Dummy Card (PC)
1)1.MS-1-D.2
While Release Lever is slid in the left, remove the Battery Pack.
2)
Slide the Lock Lever to the UNLOCK side.
Release Lever
Lock Lever
Battery Pack
Hook the finger on the Dummy Card (EXP) and remove it.
3)
Push the Eject Lever once, and the Eject Lever pops up. Push 
the Eject Lever once again, and remove the Dummy Card (PC).
Eject Lever
4)
Dummy Card (EXP)
Dummy Card (PC) 

SZ Series
Confidential
WAN Antenna (Element Unit)
1)1.MS-1-D.2(a)
WAN Model
Remove the WAN Antenna (Element Unit).
WAN Antenna (Element Unit)4
[MA] 

SZ Series
Confidential
Heatsink
1)1.MS-1-D.3
2)
3)
Remove the four screws.
While disengaging the detent (three places), remove the Cover (CPU).
Cover (CPU)
Remove the two screws.
Screw:B2
A
4)Raise the Heatsink in the direction of the arrow1, and remove the Heatsink 
while removing the A portion diagonally upward (arrow2).
1
2
Screw:B2
Heatsink 

SZ Series
Confidential
Cover (Memory)
1)1.MS-1-D.4
Remove the two screws, and remove the Cover (Memory) 
while disengaging the detent (two places).
Screw:B2
Remove the eight screws.
Screw: Red-B8 / Blue-B2
2)
Cover (Memory)
Detent 

SZ Series
Confidential
Keyboard
1) 2)1.MS-1-D.53)
Disengage the detent (two places), and release the Keyboard. 
* Disengage the detent by pushing it by using a bamboo spatula.
Slide the Keyboard in the direction of the arrow 1 to release the detent 
(five places), and turn it toward you and put it on the Plamrest.1
2
Slide the lock lever in the direction of the arrow to release the lock, 
disconnect the FPC, and then remove the Keyboard.
Keyboard
Keyboard
Keyboard
FPC
4)
Peel off the Sheet (MG KB5)....

SZ Series
Confidential
Palmrest
1) 2)1.MS-1-D.63)Raise the lock lever to release the lock, and disconnect the FFC (two places).
Remove the three screws.
Disengage the detent (six places) by sliding the Palmrest in the
direction of the arrow1, and remove the Palmrest vertically upward.
Palmrest
12
Screw:B1
FFC 

SZ Series
Confidential
HDD
1) 2)1.MS-1-D.7
Remove the three screws.
HDD
Screw:B2
3)
Peel off the Tape (Common) and Filament Tape.
FPC
Disconnect the FPC, and remove the HDD while taking out it from 
under the convex portion (one place). 
* When disconnecting the FPC, be sure to remove it from the 
direction of the arrow 1.
Convex
Connector
HD
D
1
3
[ADD]
HDD
Tape (Common)
Filament TapeWAN Model
4
[MA] 

SZ Series
Confidential
Parts of the HDD
1)1.MS-1-D.8
Remove the four screws, and then the Bracket (two places). Peel off the Sheet from backside of the HDD.
3) 4)
Disconnect the FPC.
2)
Bracket
Sheet
FPC
Peel off the Filament Tape.
Filament Tape
Screw:B10
HD
D
HDD
HDD
H D
D 

SZ Series
Confidential
Hood (Keyboard)
1)1.MS-1-D.9
Turn up the Hood (Keyboard) from the front and disengage the 
detent (eight places).
Detent
Detent
While disengaging the detent (two places) respectively, remove the 
Button (WLAN) (two places).2)
Button (WLAN)