Sony Vaio Sony Vaio Vgnfj Manual

							FJ Series
Confidential
Palmrest-2
5)1.MS-1-D.10
Palmrest
Remove the Palmrest from the front side.
6)
Open the LCD Section and disengage the detent (two places) 
from the rear side of the main unit with a bamboo spatula. 
* Push the detent lightly, and the detent is disengaged.
Rear Side 
						

							FJ Series
Confidential
LCD Section-1
1.MS-1-D.11
Disconnect the Harness (two places) by pulling it out.
3)1)
Slide the lock lever upward to release the lock, and remove the FPC 
(one place).
FPC (ILINK-Main)
Lock Lever
Harness(Camera)
Pull out the Harness (one place).
2)
Camera Model
Harness(LCD)
Harness(MIC) 
						

							FJ Series
Confidential
LCD Section-2
4)1.MS-1-D.126)
Bracket (RJ11-RJ45)
Screw: B1
Remove the screw, and remove the Bracket.
Screw: B8
Remove the six screws, lift up the LCD Section with both hands, and remove the LCD Section. 
* Hold the LCD Section not to fall down. 
* The lug terminal is secured together with the Hinge (L) with a screw.
LCD Section
Hinge L
Hinge R
Lug Terminal
Remove the Coaxial Cable (two places) vertically with tweezers or the like.
Wireless LAN Card
Coaxial Cable (Gray)
Coaxial Cable (Black)
5) 
						

							FJ Series
Confidential
Cooling Unit
1)2)1.MS-1-D.133)
Remove the six screws in order.
* These screws are built-in screws of the Cooling Unit. Pull out the Harness (one place) upward.
Harness
Cooling Unit
1
2
3
4
5
6
Remove the Cooling Unit
.
Cooling Unit 
						

							FJ Series
Confidential
CPU
1)1.MS-1-D.142)
Remove the CPU vertically. 
* Be careful not to bend the pins.
CPU
CPU
RemarkRelease the lock by rotating the lock screw as shown in the picture.
Rotate the lock screw  in the counterclockwise direction with a  4 mm 
flat-head (-) screwd river and release the lock. 
						

							FJ Series
Confidential
Except1st Model
CNX-339 Board, Door (PCMCIA)
1.MS-1-D.151)
Remove the CNX Board in the direction of the arrow. 
* Remove it not to apply the excessive pressure to the Knob (Wireless).2)
3)
Remove the two screws, and the Door (PCMCIA).
Knob (Wireless)
CNX Board
Remove the three screws.
Screw: B1
Door (PCMCIA)
Screw: B1
4)
2 [MA]
Remove the Lens Polon (one place).Lens Polon
CNX Board
3[MA] 
						

							FJ Series
Confidential
CNX-344 Board
1)2)1.MS-1-D.16
Slide the lock lever upward to release the lock, and pull out the 
FPC upward. Remove the one screw.
CNX Board
Screw: B1
FPC (ILING-Main)
Lock Lever
3)
CNX Board
Remove the CNX Board in the direction of the arrow. 
						

							FJ Series
Confidential
Mother Board-1
1)1.MS-1-D.17
Peel off the Kapton Tape (one place).
3)
Peel off the DC Jack Foil (one place), and remove the DC Jack.
4)
Remove the two screws, and the Bracket.
Kapton Tape
2)
Bracket (DC Jack)
Screw:B3
1[COR]
Remove the screw and the Bracket.
DC Jack Foil
1[ADD]
Bracket (KENSINGTON)
Screw:B1
DC Jack 
						

							FJ Series
Confidential
Mother Board-2
5)1.MS-1-D.18
6)
7)Raise the Mother Board from the right side, and remove it in the direction 
of the arrow. 
*Be careful not to apply the excessive pressure to the connector portions. Disconnect the Harness (Modem) in the direction of the arrow.8)
Connector
Mother Board
Bracket(VGA)
Screw:B1
Mother Board
Remove the six screws. 
* The Bracket is secured together with the Mother Board.
Harness(Modem)
Lock Lever
Raise the lock lever upward to release the lock, and disconnect the FPC.
FPC (Audio-Main) 
						

							FJ Series
Confidential
Mother Board-3
9)1.MS-1-D.19
Bracket (VGA)
Remove the Bracket in the direction of the arrow.