Sony Vaio Sony Vaio Vgnbx Manual

BX Series
Confidential
Chapter 1. Disassembly & Assembly Guide
1.MS-1-D.1
1-3. Disassembly & Assembly
- Main Section -
MS-1  Main Section Disassembly 

BX Series
Confidential
Battery Pack
1)1.MS-1-D.2
Slide the Release Lever to the right side,
and turn over the Battery Pack to the rear side then remove it.
Battery Pack
2)
Slide the Lock Lever to the UNLOCK side.
Lock Lever
Release Lever 

BX Series
Confidential
HDD
1) 2)1.MS-1-D.3
Remove the HDD.
Remove the screw.
HDD
Screw:B20 

BX Series
Confidential
Parts of the HDD
1)1.MS-1-D.4
2)
Remove the three screws, and remove the HDD from the Holder (HDD).
HDD
Remove the Door (HDD) while disengaging the detent (two places).
Door (HDD)
Screw:B13
Insulator (HDD)
Peel off the Insulator (HDD).
3)
Holder (HDD)
Holder (HDD) 

BX Series
Confidential
Cover (Memory), Memory
1)1.MS-1-D.5
Remove the screw.
Screw:B7Remove the Cover (Memory) while disengaging the detent (two places).
2)
3)
Outspread the tabs (arrow 1), and pull out the Memory diagonally upward 
(arrow 2).
*When two Memory are installed, remove the other side of the Memory in 
the way as above.
1 2
Memory
1 

BX Series
Confidential
Optical Disc Drive, Screws
1.MS-1-D.6
Remove the 12 screws.
2)
Remark
Screw:B19
(Special screw)
1)
Push the lever once and pull out it in the direction 
of the arrow, then remove the Optical Disc Drive.
Lever
Optical Disc Drive
Screw: Red-B2 / Blue-B11 /  Green-B5 When there is a screw in the position of figure, remove 
the Optical Disk Drive after removing the screw. 

BX Series
Confidential
Hood (Keyboard)
1) 2)1.MS-1-D.73)
Peel off the Rubber (Screw) (two places). Remove the two screws.
Keyboard
Keyboard
Turn over the Hood (Keyboard) to the rear side.
* The detents (10 places) are engaged.
Hood (Keyboard)
Disconnect the FFC and the Harness.
*FFC --- Slide the lock lever upward and release the lock.
Harness --- Pull out it upward.
4)
FFC
Harness
Screw:B3
Rubber (Screw) 

BX Series
Confidential
Parts of the Hood (Keyboard) -1
1) 2)1.MS-1-D.83)
Disconnect the FFC (two places).
*Slide the lock lever in the direction of the arrow, and release the lock.
Remove the four screws and the SWX Board. Disconnect the Harness.4)
SWX Board
Screw: B4
FFC
Harness
Kapton Tape1st Model
Kapton Tape
4[MA]
Peel off the Kapton Tape.
*1st Model --- Five places Other --- One place 

BX Series
Confidential
Parts of the Hood (Keyboard) -2
5) 6)1.MS-1-D.9
Disconnect the FFC.
*Slide the lock lever in the direction of the arrow and release the lock.Remove the two screws and the SWX Board.
SWX Board
Screw: B4
Remove the two screws and the IFX Board.
IFX Board
Screw: B11
FFC
7)
The FFC is secured with double side tape (two places).
Remark2nd Model
4[MA]
FFC
Double Side Tape 

BX Series
Confidential
Keyboard -1
1)1.MS-1-D.10
Release the Harness from the detent (five places).
Remove the three screws.
Screw: B5
Release the rib (two places) by sliding the Keyboard in the direction of 
the arrow 1, and lift it from the front side lightly.
*Notice : The FPC coming from the Keyboard is connected with Mother Board.
3) 4) 2)
Camera Model
Harness
FPC
Keyboard
Rib
Rib
1
2
FPC
Slide the lock lever in the direction of the arrow 
and release the lock, then disconnect the FPC.