Sony Shake 7 User Manual

							model name [SHAKE-7]
[4-451-239-11(1)] GB
31GB
filename[D:\NORMS JOB\SONY HA\SO120050\SHAKE-
7\%1239111_GB\ADD.fm]masterpage:Right
Additional Information
Bluetooth device
Pairing cannot be done. Move the Bluetooth device closer to the 
system.
 Pairing may not be possible if other 
Bluetooth devices are present around the 
system. In this case, turn off the other 
Bluetooth devices.
 Make sure the correct passkey was 
entered at the Bluetooth device.
Connection is not possible.Bluetooth device you attempted to 
connect does not support the A2DP 
profile, and cannot be connected with 
the system.
 Enable the Bluetooth function of the 
Bluetooth device.
 Establish a connection from the 
Bluetooth device.
 The pairing registration information has 
been erased. Perform the pairing 
operation again.
 While connected to a Bluetooth device, 
this system cannot be detected and a 
connection cannot be established from 
another Bluetooth device which is never 
paired before.
 Erase the pairing registration 
information of the Bluetooth device 
(page 20) and perform the pairing 
operation again (page 18).
The sound skips or fluctuates, or the 
connection is lost.
 The system and the Bluetooth device are 
too far apart.
 If there are obstacles between the 
system and your Bluetooth device, 
remove or avoid the obstacles.
 If there is equipment that generates 
electromagnetic radiation, such as a 
wireless LAN, other Bluetooth device, 
or a microwave oven nearby, move 
them away.
The sound of your Bluetooth device 
cannot be heard on this system.
 Increase the volume on your Bluetooth 
device first, and then adjust the volume 
using VOLUME +/–.
There is severe hum, noise or 
distorted sound.
 If there are obstacles between the 
system and your Bluetooth device, 
remove or avoid the obstacles.
 If there is equipment that generates 
electromagnetic radiation, such as a 
wireless LAN, other Bluetooth device, 
or a microwave oven nearby, move 
them away.
 Turn down the volume of the connected 
Bluetooth device.
To reset the system
If the system still does not operate 
properly, reset the system to factory 
default settings.
Use the buttons on the unit to perform this 
operation.
1Unplug and plug the power cord 
back in.
2Press "/1 to turn on the system.
3Hold down x and LED COLOR at 
the same time for about 3 seconds.
“RESET” appears in the display panel.
All user-configured settings, such as 
preset radio stations, timer, and the 
clock are reset to factory default 
setting. 
						

							model name [SHAKE-7]
[4-451-239-11(1)] GB
32GB
filename[D:\NORMS JOB\SONY HA\SO120050\SHAKE-
7\%1239111_GB\ADD.fm]masterpage:Left
Messages
Disc/Timer
NO DISC
There is no disc on the disc tray or you 
have loaded a disc that cannot be played 
back on this system.
NO STEP
All of the programmed steps have been 
erased.
NOT IN USE
You tried to perform a specific operation 
under conditions where that operation is 
prohibited.
OFF TIME NG
The Play Timer or Recording Timer start 
time and stop time is the same.
PUSH SELECT
You tried to set the clock or timer during 
timer operation.
PUSH STOP
You tried to perform an operation that can 
be performed only when the playback is 
stopped.
READING
The system is reading information of the 
disc or USB device. Some operations are 
not available.
STEP FULL
You tried to program more than 25 steps.
UNLOCK
The disc theft-preventive function is 
released.
USB device
DEVICE FULL
The memory of the USB device is full.
FATAL ERROR
The USB device was removed during 
transfer or erase operation, and may have 
been damaged.FOLDER FULL
The number of folders has reached the 
maximum.
NO DEVICE
No USB device is connected.
NO MEMORY
The memory selected for playback or 
transfer has no memory media inserted in 
the USB device.
NO STEP
All of the programmed steps have been 
erased.
NO TRACK
No playable file is loaded in the system.
NOT IN USE
You tried to perform a specific operation 
under conditions where that operation is 
prohibited.
NOT SUPPORTED
An unsupported or unknown USB device 
is connected, or the USB device is 
connected through a USB hub.
PROTECTED
The USB device is write-protected.
PUSH STOP
You tried to perform an operation that can 
be performed only when the playback is 
stopped.
READING
The system is reading information of the 
USB device. Some operations are not 
available.
REC ERROR
The transfer did not start, stopped 
partway, or otherwise could not be 
performed.
STEP FULL
You tried to program more than 25 steps.
TRACK FULL
The number of files has reached the 
maximum. 
						

							model name [SHAKE-7]
[4-451-239-11(1)] GB
33GB
filename[D:\NORMS JOB\SONY HA\SO120050\SHAKE-
7\%1239111_GB\ADD.fm]masterpage:Right
Additional Information
Precautions
When carrying the unit
Perform the following procedure to 
protect the disc mechanism.
Use the buttons on the unit to perform this 
operation.
1Press "/1 to turn on the system.
2Press CD.
3Remove the disc.
Press Z OPEN/CLOSE to open and 
close the disc tray.
Wait until “NO DISC” appears in the 
display panel.
4Hold down CD and FLANGER for 
3 seconds. 
“MECHA LOCK” appears in the 
display panel.
5Unplug the power cord.
Notes on discs Before playing, wipe the disc with a cleaning 
cloth from the center outward to the edge.
 Do not clean discs with solvents, such as 
benzine, thinner, or commercially available 
cleaners or anti-static spray intended for vinyl 
LPs.
 Do not expose discs to direct sunlight or heat 
sources such as hot air ducts, nor leave it in a 
car parked in direct sunlight.
On safety Completely disconnect the power cord (mains 
lead) from the wall outlet (mains) if it is not 
going to be used for an extended period of 
time. When unplugging the unit, always grip 
the plug. Never pull the cord itself.
 Should any solid object or liquid get into the 
system, unplug the system, and have it 
checked by qualified personnel before 
operating it again.
 AC power cord must be changed only at the 
qualified service shop.
On placement Do not place the system in an inclined 
position or in locations that are extremely hot, 
cold, dusty, dirty, or humid or lacking 
adequate ventilation, or subject to vibration, 
direct sunlight or a bright light.
 Be careful when placing the unit or speakers 
on surfaces that have been specially treated 
(for example, wax, oil, polish) as staining or 
discoloration of the surface may result.
 If the system is brought directly from a cold to 
a warm location or is placed in a very damp 
room, moisture may condense on the lens 
inside the unit, and cause the system to 
malfunction. In this situation, remove the 
disc, and leave the system turned on for about 
an hour until the moisture evaporates.
On heat buildup Heat buildup on the unit during operation is 
normal and is not a cause for alarm.
 Do not touch the cabinet if it has been used 
continuously at a high volume because the 
cabinet may have become hot.
 Do not obstruct the ventilation holes.
On the speaker systemThis speaker system is not magnetically 
shielded, and the picture on nearby TV sets may 
become magnetically distorted. In this situation, 
turn off the TV, wait 15 to 30 minutes, and turn 
it back on. If there is no improvement, move the 
speakers far away from the TV.
Cleaning the cabinetClean this system with a soft cloth slightly 
moistened with a mild detergent solution.
Do not use any type of abrasive pad, scouring 
powder, or solvent, such as thinner, benzine, 
or alcohol.
On Bluetooth CommunicationBluetooth devices should be used within 
approximately 10 meters (unobstructed 
distance) of each other. The effective 
communication range may become shorter 
under the following conditions.
– When a person, metal object, wall or other 
obstruction is between the devices with a 
Bluetooth connection
– Locations where a wireless LAN is installed
– Around microwave ovens that are in use
– Locations where other electromagnetic 
waves occur 
						

							model name [SHAKE-7]
[4-451-239-11(1)] GB
34GB
filename[D:\NORMS JOB\SONY HA\SO120050\SHAKE-
7\%1239111_GB\ADD.fm]masterpage:Left
Bluetooth devices and wireless LAN 
(IEEE 802.11b/g) use the same frequency 
band (2.4 GHz). When using your Bluetooth 
device near a device with wireless LAN 
capability, electromagnetic interference may 
occur. This could result in lower data transfer 
rates, noise, or inability to connect. If this 
happens, try the following remedies:
– Try connecting this system and Bluetooth 
device when you are at least 10 meters away 
from the wireless LAN equipment.
– Turn off the power to the wireless LAN 
equipment when using your Bluetooth 
device within 10 meters.
 The radio waves broadcast by this system may 
interfere with the operation of some medical 
devices. Since this interference may result in 
malfunction, always turn off the power on this 
system and Bluetooth device in the following 
locations:
– In hospitals, on trains, in airplanes, at gas 
stations, and any place where flammable 
gases may be present
– Near automatic doors or fire alarms
 This system supports security functions that 
comply with the Bluetooth specification as a 
means of ensuring security during 
communication using Bluetooth technology. 
However, this security may be insufficient 
depending on the setting contents and other 
factors, so always be careful when performing 
communication using Bluetooth technology.
 Sony cannot be held liable in any way for 
damages or other loss resulting from 
information leaks during communication 
using Bluetooth technology.
Bluetooth communication is not necessarily 
guaranteed with all Bluetooth devices that 
have the same profile as this system.
Bluetooth devices connected with this system 
must comply with the Bluetooth specification 
prescribed by the Bluetooth SIG, Inc., and 
must be certified to comply. However, even 
when a device complies with the Bluetooth 
specification, there may be cases where the 
characteristics or specifications of the 
Bluetooth device make it impossible to 
connect, or may result in different control 
methods, display or operation.
 Noise may occur or the audio may cut off 
depending on the Bluetooth device connected 
with this system, the communications 
environment, or surrounding conditions.
Specifications
Amplifier section
The following are measured at
Mexican model: 
AC 120 V – 240 V, 60 Hz
Other models:
AC 120 V – 240 V, 50/60 Hz
Tweeters/woofers
Power Output (rated): 
320 W + 320 W (at 4 ohms, 1 kHz, 
1% THD)
RMS output power (reference): 
520 W + 520 W (per channel at
4 ohms, 1 kHz)
Mid speakers
Power Output (rated): 
240 W + 240 W (at 5 ohms, 1 kHz, 
1% THD)
RMS output power (reference): 
385 W + 385 W (per channel at 
5 ohms, 1 kHz)
Subwoofers
Power Output (rated):   
320 W + 320 W (at 4 ohms, 100 Hz, 
1% THD) 
RMS output power (reference): 
520 W + 520 W (per channel at 
4 ohms, 100 Hz)
Inputs
TV/DVD/SAT (AUDIO IN) L/R
Voltage 2 V, impedance 47 kilohms
PC/GAME (AUDIO IN) L/R
Voltage 2 V, impedance 47 kilohms
MIC
Sensitivity 1 mV, impedance 
10 kilohms
 A (USB),   B (USB) port: Type A 
						

							model name [SHAKE-7]
[4-451-239-11(1)] GB
35GB
filename[D:\NORMS JOB\SONY HA\SO120050\SHAKE-
7\%1239111_GB\ADD.fm]masterpage:Right
Additional Information
USB section
Supported bit rate
WMA:
48 kbps – 192 kbps, VBR, CBR
AAC:
48 kbps – 320 kbps, VBR, CBR
Sampling frequencies
WMA:
44.1 kHz
AAC:
44.1 kHz
Supported USB device
Mass Storage Class
Maximum current
500 mA
Disc/USB section
Supported bit rate
MPEG1 Layer-3:
32 kbps – 320 kbps, VBR
MPEG2 Layer-3:
8 kbps – 160 kbps, VBR
MPEG1 Layer-2:
32 kbps – 384 kbps, VBR
Sampling frequencies
MPEG1 Layer-3:
32 kHz/44.1 kHz/48 kHz
MPEG2 Layer-3:
16 kHz/22.05 kHz/24 kHz
MPEG1 Layer-2:
32 kHz/44.1 kHz/48 kHz
Disc player section 
System
Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6 PW
* This output is the value measurement at 
a distance of 200 mm from the objective 
lens surface on the Optical Pick-up 
Block with 7 mm aperture.
Frequency response
20 Hz – 20 kHz
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 88 dB
Tuner section
FM stereo, FM/AM superheterodyne tuner
Antenna:
FM lead antenna
AM loop antenna
FM tuner section
Tuning range
87.5 MHz – 108.0 MHz (50 kHz step)
AM tuner section
Tuning range
Pan American models:
531 kHz – 1,710 kHz (9 kHz step)
530 kHz – 1,710 kHz (10 kHz step)
Saudi Arabian model:
531 kHz – 1,602 kHz (9 kHz step)
Other models:
531 kHz – 1,602 kHz (9 kHz step)
530 kHz – 1,610 kHz (10 kHz step) 
						

							model name [SHAKE-7]
[4-451-239-11(1)] GB
36GB
filename[D:\NORMS JOB\SONY HA\SO120050\SHAKE-
7\%1239111_GB\ADD.fm]masterpage:Left
Bluetooth section
Communication system
Bluetooth Standard version 3.0 + EDR 
(Enhanced Data Rate)
Output
Bluetooth Standard Power Class 2
Maximum communication range
Line of sight approx. 10 m
1)
Frequency band
2.4 GHz band (2.4000 GHz – 
2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread 
Spectrum)
Compatible Bluetooth profiles
2)
A2DP (Advanced Audio Distribution 
Profile)
AVRCP 1.3 (Audio Video Remote 
Control Profile)
Supported codecs
SBC (Sub Band Codec)
AAC (Advanced Audio Coding)
1)The actual range will vary depending on 
factors such as obstacles between devices, 
magnetic fields around a microwave oven, 
static electricity, reception sensitivity, 
antenna’s performance, operating system, 
software application, etc.
2)Bluetooth standard profiles indicate the 
purpose of Bluetooth communication between 
devices.
Speakers
Speaker system
4-way, Bass reflex
Speaker unit
Woofers: 200 mm, cone type
Tweeters: 25 mm, horn type
Mid speakers: 100 mm, cone type
Subwoofers: 380 mm, cone type
Rated impedance
Tweeters/woofers: 4 ohms
Mid speakers: 5 ohms
Subwoofers: 4 ohms
Dimensions (w/h/d) (Approx.)
510 mm × 750 mm × 446 mm
Mass (Approx.)
32 kg
Quantity: 2 pieces
General
Power requirements
Mexican model: 
AC 120 V – 240 V, 60 Hz
Other models:
AC 120 V – 240 V, 50/60 Hz
Power consumption
420 W
Dimensions (w/h/d) (excl. speakers) 
(Approx.)
500 mm × 220 mm × 380 mm
Mass (excl. speakers) (Approx.)
8.4 kg
Supplied accessories
Remote control (1)
R6 (Size AA) batteries (2)
FM lead/AM loop antenna (1)
Design and specifications are subject to 
change without notice. 
						

							©2013 Sony Corporation   Printed in Malaysia
model name [SHAKE-7]
[4-451-239-11(1)] GB
filename[D:\NORMS JOB\SONY HA\SO120050\SHAKE-
7\4451239111_GB\BPG.fm]masterpage:Bcov