Sony Projector Vpl Vw80 User Manual

61 
Others
This section describes about the other functions, how to solve the problems, how to 
replace the lamp and air filter, etc.
About the Control for 
HDMI
What is the Control for HDMI?
Control for HDMI is an HDMI standard 
mutual control function which uses the 
HDMI CEC (Consumer Electronics 
Control) specification. By connecting a 
variety of Sony Control for HDMI 
compatible equipment such as a hard disk 
Blu-ray Disc player, a DVD player/recorder, 
an AV amplifier, etc. to a Sony Control for...

 62
 The available functions of the Control for 
HDMI differ depending on each 
equipment. Refer to the operating 
instruction of each equipment.
 Some synchronization may be available 
with equipment of other brands with 
similar functions, but it is not guaranteed.
About the x.v.Color
 “x.v.Color” is a promotion name given to 
the products that have the capability to 
realize a wide color space based on the 
xvYCC specifications and is a trademark 
of Sony Corporation.
 xvYCC is an international...

63 
Others
Troubleshooting
If the projector appears to be operating erratically, try to diagnose and correct the problem 
using the following instructions. If the problem persists, consult with qualified Sony 
personnel.
Power
Picture
Symptom Cause and Remedy
The power is not turned on.cThe power may not turn on if you turn the power off with ?/1 
(ON/STANDBY) switch and turn it on again in a short time.
After about 1 minute, turn the power on. 
cClose the lamp cover securely, then tighten the screws...

 64
On-screen display
Remote control
The picture is too dark.cAdjust the “Contrast” or “Brightness” of the Picture   menu 
properly. (1 pages 47, 48)
The picture is not clear.cAdjust the focus. (1 page 26)
cCondensation has accumulated on the lens. Leave the projector 
for about 2 hours with the power on.
The picture flickers.cFor pictures from a computer, activate “APA” and adjust the 
current input signal.
cAdjust “Phase” for “Adjust Signal” in the Screen   menu 
properly. (1 page 52)
The color of...

65 
Others
Others
Symptom Cause and Remedy
The fan is noisy.cCheck the setting of “Cooling Setting” in the Setup   menu. 
(1 page 53)
cMake sure that the room temperature is not too high.
cCheck the installation conditions. (1 page 12)
The number of fan rotation increases to maintain the product 
reliability of the projector’s components in a room, where the 
temperature is higher than normal. The fan noise becomes 
slightly louder. The approximate normal temperature is 25°C.
The lens shift cannot be...

 66
The ON/STANDBY or LAMP/COVER indicator lights up or flashes if there is any 
trouble with your projector.
Warning Indicators
Symptom Cause and Remedy
LAMP/COVER flashes in 
red. (A repetition rate of 2 
flashes)cClose the lamp cover securely, then tighten the screws securely. 
(1 page 70)
cClose the filter holder securely. (1 page 71)
LAMP/COVER flashes in 
red. (A repetition rate of 3 
flashes)cThe lamp has reached the end of its useful lifespan. Replace the 
lamp. (1 page 69)
cThe lamp has reached...

67 
Others
When a warning indicator other than the above starts flashing, and the symptom persists even after 
carrying out the above methods, consult with qualified Sony personnel. 
Warning messages
ON/STANDBY flashes in 
red. (A repetition rate of 5 
times)cThe lens protector is not fully open. Turn the power of the 
projector off and then on again. If the lens protector still does not 
fully open, consult with qualified Sony personnel.
Tip
In an urgent situation, refer to the illustration below to...

 68
Caution messages
Please clean the filter.cIt is time to clean the air filter. Clean the air filter. (1 page 72)
To clear this message, press any button either on the remote control 
or the control panel of the projector once.
Please clean the filter. Have 
you finished? Yes NocIt is time to clean the air filter. Clean the air filter. (1 page 72)
cIf you cleaned the air filter, select “Yes.” If you did not clean the 
air filter, select “No.”
Projector temperature is 
high.  Cooling Setting 
should be...

69 
Others
Replacing the Lamp 
and the Air Filter and 
Cleaning the 
Ventilation Holes 
(intake)
Tools you need to get started:
 Projector Lamp LMP-H201 (Optional)
Standard Phillips screwdriver
Cloth (for scratch protection)
The lamp used for the light source has a 
certain lifespan. When the lamp dims, the 
color balance of the picture becomes strange, 
or “Please replace the Lamp/Filter.” appears 
on the screen, the lamp may be exhausted. 
Replace the lamp with a new one (not 
supplied) 
without...

 70
3Loosen the screw on the lamp 
cover with a Philips screwdriver, 
and then open the lamp cover.
4Loosen the 3 screws on the 
lamp with the Phillips 
screwdriver. Hold up the handle, 
then pull the lamp straight out.
5Hold the handle of the new lamp 
and push it in securely until it 
reaches the end, and then 
tighten the 3 screws.
Be careful not to touch the optical block 
inside the unit.
6Close the lamp cover, then 
tighten the screws.
Note