Sony Projector VPL-VW665 User Manual

31
Advanced Picture Menu
You can adjust the gaps in color that have occurred after a long period of use.
 Auto Calibration results in relatively coarse calibration. No warranty is given for the color settings 
to be the same as the factory default values.
 While performing “Pre Check” or “Adjust,” the colors are projected automatically. This is not a 
malfunction.
 Do not turn off the power or operate the remote control or control panel during “Pre Check” or 
“Adjust”, as the process may be canceled....

32
Screen Menu
You can set the picture size, aspect mode, etc.
These items may not be available, depending on the type of input signal. For details, see “Input 
Signals and Adjustable/Setting Items” (page 59).
Item names in brackets represent those printed on the remote control.
Note
Setting items Description
Picture Position
[POSITION]You can store up to five combinations of lens settings, aspect ratio, and 
blanking.
After setting the lens, aspect, and blanking, select from “1.85:1,” 
“2.35:1,” “Custom...

33
Aspect
[ASPECT]You can set the aspect ratio of the picture to be displayed for the current 
input signal (page 19). 
You can set the function only when a video signal other than a resolution 
of 4096 × 2160 pixels is input.
1.85:1 Zoom: A 1.85:1 aspect ratio picture is displayed in its original 
aspect ratio, enlarged so that black bands do not appear at the top and 
bottom of the screen.
2.35:1 Zoom: A 2.35:1 aspect ratio picture is displayed in its original 
aspect ratio, enlarged so that black...

34
Setup Menu
The Setup menu is used to change the factory preset settings, etc.
Setting items Description
Status Sets whether or not the on-screen display is displayed.
Set to “Off” to turn off the on-screen displays except for certain menus, 
message when turning off the power, and warning messages.
Language Selects the language used in the menu and on-screen displays.
Menu Position You can change the position to display the menu on the screen.
Bottom Left: Displays the menu on the bottom left area of...

35
Network ManagementOn: Set when connected to the network and continuously 
communicating with the projector control equipment.
When Network Management is set to “On,” the network function is 
continuously enabled. Set Network Management to “Off” for normal 
use. If you set to “On,” the power consumption increases.
Power Saving Sets the power saving mode.
Standby: If no signal is input for 10 minutes, power is turned off 
automatically and the projector goes into standby mode.
Off: Disables the power...

36
Function Menu
The Function menu is used for changing the settings of the various functions of the unit.
Setting items Description
3D Settings You can change the settings of the 3D function.
2D-3D Display 
Sel.For Switching the video images to “2D” or “3D.”
Auto: Displays 3D video images when HDMI signals with 3D 
information* are input. Displays 2D video images when other signals 
are input.
3D: Displays 3D video images according to the 3D system selected in 
“3D Format.” However, when HDMI signals...

37
3D Depth Adjust For adjusting the depth of the 3D video images on the screen. The 
setting can be made only when a 3D Format other than “Simulated 3D” 
is selected.
We recommend that “3D Depth Adjust” be set to “0.” The 3D video 
images may be difficult to perceive, depending on the setting of “3D 
Depth Adjust.”
Simulated 3D 
EffectFor adjusting the 3D effect when 2D content is converted to 3D video 
images. You can select the effect from among “High,” “Middle,” and 
“Low.”
Tip
There are differences...

38
Group 1 Group 2
Items Locked by Settings Lock
Picture menu
Reset
Reality Creation
Advanced Iris
Contrast Enhancer
Lamp Control
Motionflow
Contrast
Brightness
Color
Hue
Color Temp.
Sharpness
NR
MPEG NR
Smooth Gradation
Film Mode
Gamma Correction
Color Correction
Clear White
x.v.Color
HDR
Color Space
Advanced Picture menu
Auto CalibrationSetup menu
Status
Language
Menu Position
High Altitude Mode 
Remote Start
Network Management
Lamp Setting
Function menu
Dynamic Range
Test Pattern
Installation menu...

39
Installation Menu
The Installation menu is used for changing the installation settings.
Setting items Description
Image Flip Flips the picture on the screen horizontally and/or vertically.
HV: Flips the picture horizontally and vertically.
H: Flips the picture horizontally. 
V: Flips the picture vertically.
Off: The picture does not flip.
Use this item for installation for the backside projection or ceiling 
installation.
Lens Control Avoids any operation of the lens such as “Lens Focus,” “Lens Zoom,”...

40
Panel Alignment This feature allows you to adjust the gaps in the color of characters or 
the picture on the screen.
Adjust: Adjusts the gaps in the colors selecting “Adjust Color” or 
“Adjust Item.”
Adjust Item: Selects how to make adjustments from below.
Shift: Shifts the whole picture and makes adjustments.
Zone: Selects the desired range and makes adjustments.
Adjust Color: Assigns the desired color to adjust the gaps in color. 
Select “R” (Red) or “B” (Blue) to make adjustments based on “G”...