Sony Projector VPL-VW1100ES User Manual

							51 
Using Network Features
Displaying the 
Control Window of 
the Unit with a Web 
Browser
1Connect the LAN cable.
2Set the network settings for the 
unit using “Network Setting” on 
the Installation   menu (1 
page 48).
3Start a web browser on the 
computer, enter the following in 
the address field, then press the 
Enter key on your computer.
http://xxx.xxx.xxx.xxx
(xxx.xxx.xxx.xxx: IP address for the 
unit)
You can confirm the IP address of the 
unit under “Network Setting” on the 
Installation  menu.
The following window appears in the 
Web browser:Once you make the network settings, 
you can open the Control window only 
by performing step 3 of this procedure.
LAN cable 
(straight type) 
(not supplied)
Hub, router, etc.
LAN Connector 
						

							 52
Operating the 
Control Window
Click one of the Page Switching buttons to 
display the desired setting page.
You can limit a user for accessing any 
particular page.
Administrator: Allowed access to all 
pages
User: Allowed access to all pages 
except the Setup page
Set under [Password] of the Setup page.
When you access the Setup page for the first 
time, enter “root” for user name and enter 
“Projector” for password.
The name of the administrator is preset to 
“root.”
When you change the password, input a new 
password after deleting the password 
(*****) that was set.
If you forget your password, consult with 
qualified Sony personnel.
You can confirm the current settings for the 
unit on the Information page.
You can control the unit from the computer 
on the Control page.
The functions of the buttons shown in the 
operation area are the same as those of the 
buttons on the supplied remote control.
Switching the Page
Setting the Access Limitation
Page Switching buttons
Entry area for [Administrator]
Entry area for [User]
Note
Confirming the Information 
Regarding the Unit
Operating the Unit from a 
Computer
Information area
Operation area 
						

							53 
Using Network Features
Set the e-mail report function on the Setup 
page.
Entered values will not be applied unless 
you click on [Apply].
1Click on [Owner information] to 
enter the owner information 
recorded in the 
e-mail report.
2Set the timing of the e-mail 
report.
Click on [Mail Report] to open the Mail 
Report page.
Lamp Reminder (Lamp1): Set the 
timing for lamp replacement. To reset 
Lamp Reminder, execute “Lamp 
Setting” on the unit (1 page 41).
Maintenance Reminder: Set the timing 
for maintenance. To reset 
Maintenance Reminder, check the 
RESET check box and then click on 
[Apply].
3Enter the outgoing e-mail 
address in the Email Address 
box, then check the Report 
Timing check box of the e-mail 
report to be sent.
4Set the mail account for sending 
e-mail reports.
Mail Address: Enter the e-mail address.
Outgoing Mail Server (SMTP): Enter 
the address of outgoing mail server 
(SMTP).
Required Authentication: Check this 
check box if authentication is required 
for sending e-mail.
Requires the use of POP 
Authentication before send email 
(POP before SMTP): Check this 
check box to arrange for POP 
authentication to be performed before 
sending e-mail.
Incoming Mail Server (POP3): Enter 
the address of the incoming-mail 
server (POP3) to be used for POP 
authentication.
Account Name: Enter the mail account.
Password: Enter the password.
Using the E-mail Report 
Function
1Owner information button
2
3
4
6
5
Mail Report button 
						

							 54
SMTP Authentication: Check this 
check box to arrange for SMTP 
authentication to be performed before 
sending e-mail.
Account Name: Enter the mail account.
Password: Enter the password.
5Confirm the contents of the e-
mail report.
When you click on [View], the contents 
of the e-mail report are displayed.
6Send the test mail.
Check on the Send test mail check box, 
then click on [Apply] to send your test 
mail to the e-mail address you set.
 You cannot use the e-mail report function 
because Outbound Port 25 Blocking on the 
network is preventing a connection to the 
SMTP server.
 You cannot enter the following characters in 
the text box: , , \, &, 
Notes 
						

							55 
Others
This section describes about the other functions, how to solve the problems, how to 
replace the lamp, etc.
About the Control for 
HDMI
What is the Control for HDMI?
Control for HDMI is an HDMI standard 
mutual control function which uses the 
HDMI CEC (Consumer Electronics 
Control) specification. By connecting a 
variety of Control for HDMI compatible 
equipment such as a hard disk Blu-ray Disc 
player, a DVD player/recorder, an AV 
amplifier, etc. to a Sony Control for HDMI 
compatible TV or a projector with an HDMI 
cable, the equipment connected will 
synchronize with the TV or the projector 
when either is operated.
Using the Control for HDMI 
function
 Connect and assign the settings of each 
equipment appropriately.
 Do not turn off the main power of the 
equipment.
 Set the input setting of the projector to the 
HDMI input which the equipment is 
connected.
 Check if the picture from the equipment 
appears appropriately on the projector.
Connecting a Control for HDMI 
compatible equipment
Use an HDMI cable to connect the projector 
and the Control for HDMI compatible 
equipment. Use a cable that has acquired the 
HDMI logo.
Setting the Control for HDMI
Be sure to assign the appropriate settings for 
both the projector and the Control for HDMI 
compatible equipment connected to the 
projector. For settings of the projector, see page 43. For settings of the Control for 
HDMI compatible equipment connected to 
the projector, refer to its operating 
instructions. When equipment that is 
compatible with the “Control for HDMI - 
Easy Setting” is connected to the HDMI 
input of the projector, if you turn the Control 
for HDMI function setting of the projector 
on, the Control for HDMI function setting of 
the connected equipment will also turn on.
What you can do with the 
Control for HDMI
 By turning on or playing back the 
connected equipment, the projector will 
turn on and the input setting will switch to 
the terminal of the connected equipment 
automatically.
 By turning the power of the projector off, 
the power of the connected equipment will 
also turn off automatically.
 By changing the language setting of the 
projector, the language setting of the 
connected equipment will also change to 
the same language automatically.
 The available functions of the Control for 
HDMI differ depending on each equipment. 
Refer to the operating instruction of each 
equipment.
 Some synchronization may be available with 
equipment of other brands with similar 
functions, but it is not guaranteed.
Others
Notes 
						

							 56
About DCI 
specification
DCI is a specification for Digital cinema 
projection systems, established by the 
industry standards body DCI (Digital 
Cinema Initiatives), an affiliation of six 
major Hollywood studios.
About the x.v.Color
 “x.v.Color” is a promotion name given to 
the products that have the capability to 
realize a wide color space based on the 
xvYCC specifications and is a trademark 
of Sony Corporation.
 xvYCC is an international standard of the 
technical specifications of the extended-
gamut color space for video signals. The 
color gamut of xvYCC is wider than the 
one of sRGB that is used with the current 
television system.
About the simulated 
3D feature
 Use the simulated 3D function taking into 
account that the picture will provide a 
different look from the original images, 
because this function converts the video 
images.
 Note that if the unit is used for profit or for 
public viewing, displaying 2D video 
images as 3D video images by converting 
to the simulated 3D may constitute an 
infringement of the rights of authors or 
producers, which are legally protected. 
						

							57 
Others
Troubleshooting
If the unit appears to be operating erratically, try to diagnose and correct the problem using 
the following instructions. If the problem persists, consult with qualified Sony personnel.
Power
Picture
Symptom Cause and Remedy
The power is not turned on.cThe power may not turn on if you turn the power off with 
?/1 
(ON/STANDBY) button and turn it on again in a short time.
After about 1 minute, turn the power on. 
cClose the lamp cover securely, then tighten the screws securely 
(1 page 64).
cCheck warning indicators (1 page 60).
The power is suddenly 
turned off.cCheck that “Power Saving” in the Setup   menu is set to 
“Standby.” (1 page 41)
cSet “Power Saving” to “Off.”
Symptom Cause and Remedy
No picture.cCheck that the connecting cable is connected to the external 
equipment properly (1 page 13).
Depending on the external equipment, the unit may not function 
correctly via the HDMI 1 connector. In this case, use the HDMI 
2 connector, then select the input.
cSelect the input source correctly using the INPUT button
 (1 page 17).
cCheck that the computer signal is set for output to an external 
monitor.
cIf the notebook computer, etc., signal is output to its display and 
an external monitor, the external monitor’s image may not be 
displayed correctly. Set your computer to output the signal to 
only an external monitor.
The picture has ghosts.cVideo images are displayed in 3D. Watch the 3D video images 
using the 3D glasses, and set “2D-3D Display Sel.” to “3D” (1 
page 42).
To convert 3D video images to 2D video images, set “2D-3D 
Display Sel.” to “2D.”
Bright or dark area of the 
video appears too bright or 
too dark.cThis symptom may occur when RGB signal level other than 
those of HDMI standard is input. Switch the RGB output level 
of the connected equipment, or switch the HDMI Dynamic 
Range of the unit (1 page 44).
The picture is too dark.cAdjust “Contrast” or “Brightness” on the Picture   menu 
properly (1 page 33).
The picture is not clear.cAdjust the focus (1 page 9).
cCondensation has accumulated on the lens. Leave the unit for 
about 2 hours with the power on. 
						

							 58
On-screen display
Remote control
The picture flickers.cFor pictures from an analog computer, adjust “Phase” for 
“Adjust Signal” on the Screen   menu properly (1 page 39).
The color of characters or 
the picture is not 
appropriate.cSelect the desired color registration in “Panel Alignment” of the 
Installation  menu (1 page 47).
Image is left on the screen. 
(image retention)cWhen high contrast non-moving images are displayed for a long 
period of time, there may be some image retention on the 
screen. This is only a temporary condition. Turning off the 
power for a while will eliminate the retained image. Symptom Cause and Remedy
Symptom Cause and Remedy
On-screen display does not 
appear.cSet “Status” on the Setup   menu to “On” (1 page 40).
cCheck if the ON/STANDBY indicator should light in green. 
When the ON/STANDBY indicator blinks in green, the unit is 
starting up. Wait until it stops blinking and remains lit in green.
The model name does not 
disappear from the screen.cThe display mode of the unit may be set at the time of purchase. 
Consult with your local dealer or qualified Sony personnel.
Input terminals do not 
appear.cSet “Auto Input Search” on the Function   menu to “Off” (1 
page 44).
Symptom Cause and Remedy
The remote control does 
not work.cBatteries could be weak. Replace them with new batteries.
cInsert the batteries with the correct polarities.
cIf there is a fluorescent lamp near the remote control detector, 
the unit may work improperly or inadvertently.
cIf you use the optional 3D Sync Transmitter and point it to the 
remote control detector of the unit, the remote control may not 
work properly.
cConfirm the position of the remote control detector on the unit 
(1 page 4).
cSet “IR Receiver” to “Front & Rear” on the Installation   
menu (1 page 46). 
						

							59 
Others
3D video images
Others
Symptom Cause and Remedy
The video image does not 
seem like 3D video images.cCheck if the 3D glasses are turned on (1 page 19).
cMake sure that the battery in the 3D glasses is charged.
cCheck if the input source is HDMI.
cSet “2D-3D Display Sel.” to “Auto” or “3D” (1 page 42).
cCheck if the input signals are compatible 3D signals (1 page 
73).
cIf no 3D signal is input from the 3D equipment connected to the 
unit, restarting the connected 3D equipment may solve the 
problem.
cWhen the viewing or projector position is too far from the 
screen, the 3D glasses may not be able to display the images 
properly (1 page 20).
cIf you use the optional 3D Sync Transmitter, check that it is 
placed within the specified range (1 page 16).
cThe screen size is not appropriate. Set the zooming 
magnification to low or watch the image from farther away from 
the screen (1 page 79).
Symptom Cause and Remedy
The fan is noisy.cCheck the setting of “Cooling Setting” on the Setup   menu 
(1 page 40).
cMake sure that the room temperature is not too high.
cCheck the installation conditions.
The number of fan rotation increases to maintain the product 
reliability of the projector’s components in a room, where the 
temperature is higher than normal. The fan noise becomes 
slightly louder. The approximate normal temperature is 25°C.
The lens shift cannot be 
adjusted.cThe lens shift cannot be adjusted over the range of movement. 
Adjust the lens shift within the range of movement (1 
pages 12, 78).
The unit and connected 
equipment turn On/Off, 
play back, and operate at 
the same time.c“Control for HDMI,” “Device Auto Power Off,” and “PJ Auto 
Power ON” are set to “On.” Set them to “Off.”
For details, see “HDMI Setting” (1 page 43). 
						

							 60
The ON/STANDBY or LAMP/COVER indicator lights up or flashes if there is any 
trouble with your projector.
Warning Indicators
Symptom Cause and Remedy
LAMP/COVER flashes in 
red. (A repetition rate of 2 
flashes)cClose the lamp cover securely, then tighten the screws securely 
(1 page 64).
LAMP/COVER flashes in 
red. (A repetition rate of 3 
flashes)cThe temperature of lamp is unusually high. Turn off the power 
and wait for the lamp to cool, then turn on the power again.
cIf the symptom persists, the lamp may be at the end of its service 
life. In this case, replace the lamp with a new one (1 page 63).
ON/STANDBY flashes in 
red. (A repetition rate of 4 
flashes)cThe fan is broken. Consult with qualified Sony personnel.
ON/STANDBY flashes in 
red. (A repetition rate of 2 
flashes)cThe internal temperature is unusually high. Check to ensure that 
if nothing is blocking the ventilation holes or whether or not the 
unit is being used at high altitudes.
ON/STANDBY flashes in 
red. (A repetition rate of 6 
flashes)cPress the 
?/1 (ON/STANDBY) button to turn on the unit. If the 
power is not turned on, disconnect the AC power cord, then 
confirm the ON/STANDBY lamp is turned off. After about 10 
seconds, reconnect the AC power cord and turn on the power 
again. If the indicators still light up, the electrical system has a 
problem. Consult with qualified Sony personnel.
ON/STANDBY indicator
LAMP/COVER indicator