Sony Projector VPL-VW1100ES User Manual

41 
Using the Menus
Power SavingSets the power saving mode.
Lamp Cutoff: If no signal is input for 10 minutes, the lamp turns off 
automatically and power consumption is reduced. If signal is 
resumed, or any button on the control panel or remote control is 
pressed, the lamp will light again. In Lamp Cutoff, the ON/
STANDBY indicator lights in orange. (1 page 4)
Standby: If no signal is input for 10 minutes, power is turned off 
automatically and the projector goes into standby mode.
Off: The power...

 42
Function Menu
The Function menu is used for changing the settings of the various functions of the unit. 
3D SettingsYou can change the settings of the 3D function.
2D-3D Display Sel.: For Switching the video images to “2D” or 
“3D.”
Auto: Displays 3D video images when HDMI signals with 3D 
information are input. Displays 2D video images when other 
signals are input.
3D: Displays 3D video images according to the 3D system 
selected in “3D Format.” However, when HDMI signals with 3D 
information are...

43 
Using the Menus
3D Settings3D Depth Adjust: For adjusting the depth of the 3D video images 
on the screen. The setting can be made only when a 3D Format 
other than “Simulated 3D” is selected.
We recommend that “3D Depth Adjust” be set to “0.” The 3D 
video images may be difficult to perceive, depending on the 
setting of “3D Depth Adjust.”
Simulated 3D Effect: For adjusting the 3D effect when 2D content 
is converted to 3D video images. You can select the effect from 
among “High,” “Middle,” and...

 44
HDMI SettingPJ Auto Power On: Select whether to link the power of the unit to 
the Control for HDMI compatible equipment.
When set to “On,” the power of the unit will automatically turn on 
when the power of the connected equipment is turned on or when 
making operations such as playback.
Tip
To enable this function, set “Standby Mode” (1 page 40) on the 
Setup   menu to “Standard,” and then set “PJ Auto Power On” to 
“On.” For details, see “About the Control for HDMI” (1 page 55).
Device List: Lists...

45 
Using the Menus
Test PatternDisplays a test pattern according to the setting.
On: A test pattern appears on the screen to be used when adjusting 
the lens with “Lens Focus,” “Lens Zoom,” and “Lens Shift.”
Off: A test pattern does not appear.
Tip
While the test pattern is displayed, it is only displayed in green to 
allow you to adjust the focus easily.
BackgroundSelects the background color of the screen when no signal is 
input.
You can select “Black” or “Blue.” 

 46
Installation Menu
The Installation menu is used for changing the installation settings.
Image FlipFlips the picture on the screen horizontally and/or vertically. 
HV: Flips the picture horizontally and vertically.
H: Flips the picture horizontally. 
V: Flips the picture vertically.
Off: The picture does not flip.
Use this item for installation for the backside projection or ceiling 
installation.
Lens ControlAvoids any operation of the lens such as “Lens Focus,” “Lens 
Zoom,” and “Lens Shift,” by...

47 
Using the Menus
BlankingThis feature allows you to adjust the displayable region within 
the four directions of the screen.
Select the edge to adjust by highlighting Left, Right, Top, or Bottom 
using the M/m buttons.
Adjust the amount of blanking using the 

 48
Panel AlignmentSet the amount to adjust with 

49 
Using the Menus
Information Menu
The Information menu displays the model name, serial number, the horizontal and vertical 
frequencies of the input signal and the cumulated hours of usage of the lamp.
 fH (horizontal frequency) and fV (vertical frequency) may not be displayed depending on the input 
signal used on the unit.
 You cannot adjust or change the displays listed above.
This unit has default image data to adjust preset data for input signals appropriately 
according to the signals shown in...

 50
Connection to the network allows you to operate the following features:
 Checking the current status of the unit via a Web browser.
 Remotely controlling the unit via a Web browser.
 Receiving the e-mail report for the unit.
 Making the network settings for the unit.
 Network monitoring and controlling with control protocol (SDAP [Advertisement], 
SDCP [PJ Talk], DDDP [AMX]).
 Using the gamma control software “ImageDirector3.”
 The menu displays used for the explanation below may be different...