Sony Projector VPL-SW631C User Manual
Have a look at the manual Sony Projector VPL-SW631C User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 980 Sony manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
81Replacing the Lamp Others 4Insert the new lamp all the way in until it is securely in place (1). Tighten the three screws (2). The power will not turn on if the lamp is not secured properly. 5Close the lamp cover and tighten the 1 screw. 6Connect the AC power cord to a wall outlet and turn on the projector. 7Reset the lamp timer for notification of the next replacement time. Select “Lamp Timer Reset” on the Function menu then press the ENTER key. When a message appears, select “Yes” to reset the lamp timer (page 27). Note Caution For the customers in the U.S.A. and Canada Lamp contains mercury. Dispose according to applicable local, state/ province and federal laws. For additional information, see www.sony.com/mercury
82Cleaning the Air Filter Cleaning the Air Filter When a message appears on the projected image indicating time for a filter cleaning, clean the air filter (pages 73, 59). If the dust cannot be removed from the air filter even after cleaning, replace the air filter with a new one. For details on a new air filter, consult with qualified Sony personnel. If you continue to use the projector even after the message is displayed, dust may accumulate, clogging it. As a result, the temperature may rise inside the unit, leading to a possible malfunction or fire. 1Turn off the projector, and disconnect the AC power cord from the AC outlet. 2Open the side cover. Press A and open the side cover in the direction of the arrow shown on the illustration below. 3Remove the air filter holders. Push B and remove the two air filter holders in the direction of the arrow. 4Clean the air filters with a vacuum cleaner. Remove the four air filters as illustrated below then clean with a vacuum cleaner. There are two air filters for one air filter holder. Caution A Side cover Air filter holder B Claws A B
83Cleaning the Air Filter Others 5Reattach the air filters on the air filter holders then put them back in the projector. Be sure to attach the air filters firmly. Otherwise, a malfunction may occur. 6Reattach the side cover. Note A B
84Specifications Specifications ItemsDescriptions Projection system3 LCD system Display device Effective display sizeVPL-SW636C/SW631C/SW631: 0.59 inch (15.0 mm), 3 plate panels, Aspect ratio 16:10 VPL-SX631: 0.63 inch (16.0 mm), 3 plate panels, Aspect ratio 4:3 Effective picture elementsVPL-SW636C/SW631C/SW631: 3,072,000 pixels (1280 × 800 pixels, 3 plate panels) VPL-SX631: 2,359,296 pixels (1024 × 768 pixels, 3 plate panels) Projection lens Zoom Manual (approx.1.03 times) Focus Manual Light source High-pressure mercury lamp, 225 W type Projected image sizeVPL-SW636C/SW631C/SW631: 65 inches to 110 inches (1.65 m to 2.79 m) VPL-SX631 : 70 inches to 115 inches (1.78 m to 2.92 m) Luminous flux (Brightness)VPL-SW636C/SW631C/SW631: 3300 lm VPL-SX631: 3300 lm (when “Lamp Mode” is set to “High”) Speaker 16 W × 1 (monaural) Applicable scanning frequency *1 Horizontal: 15 kHz to 92 kHz, Vertical: 48 Hz to 92 Hz Resolution *1When a computer signal is inputMaximum display resolution: 1600 × 1200 pixels (resize) Panel display resolution: VPL-SW636C/SW631C/SW631: 1280 × 800 pixels VPL-SX631: 1024 × 768 pixels When a video signal is inputNTSC, PAL, SECAM, 480/60i, 576/50i, 480/60p, 576/50p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/60p, 1080/50p Color system NTSC 3.58, PAL, SECAM, NTSC4.43, PAL-M, PAL-N, PAL60
85Specifications Others INPUT OUTPUT (Computer/ video)INPUT ARGB/YPBPR input terminal: Mini D-sub 15-pin female, G with sync/Y: 1 Vp-p ± 2 dB, sync negative, 75 ohms terminated, RGB/P BPR: 0.7 Vp-p ± 2 dB, 75 ohms terminated, Sync signal: TTL level high impedance, positive/negative Audio input terminal: Stereo mini jack, rated input 500 mVrms, input impedance more than 47 kohms INPUT BRGB input terminal: Mini D-sub 15-pin female, RGB: 0.7 Vp-p ± 2 dB, 75 ohms terminated, Sync signal: TTL level high impedance, positive/negative Audio input terminal: Stereo mini jack, rated input 500 mVrms, input impedance more than 47 kohms INPUT CHDMI input terminal: HDMI 19-pin, HDCP, HDMI audio support S VIDEO (SVIDEO IN)S video input terminal: Mini DIN 4-pin, Y: 1 Vp-p ± 2dB, sync negative, 75 ohms terminated, C: (burst signal) 0.286 (NTSC)/0.3 (PAL/SECAM) Vp-p ± 2 dB, 75 ohms terminated Audio input terminal: Phono jack × 2, rated input 500 mVrms, input impedance more than 47 kohms VIDEO (VIDEO IN)Video input terminal: Pin jack, 1 Vp-p ± 2 dB, sync negative, 75 ohms terminated Audio input terminal: Shared with S VIDEO OUTPUTMONITOR output terminal: Mini D-sub 15-pin female, G with sync/Y: 1 Vp-p ± 2 dB, sync negative, 75 ohms terminated, RGB/P BPR: 0.7 Vp-p ± 2 dB, 75 ohms terminated, Sync signal: HD, VD 4 V (open), 1 Vp-p (75 ohms), positive/negative Audio output terminal: Stereo mini jack, 1 Vrms (maximum volume, when inputting 500 mVrms), output impedance 5 kohms Other terminalsRS-232C terminal: D-Sub 9-pin male LAN terminal: RJ45, 10BASE-T/100BASE-TX USB terminal: Ty p e A USB terminal: Ty p e B Microphone input: Mini jack Operating temperature/ Operating humidity0 °C to 40 °C (32 °F to 104 °F)/20% to 80% (no condensation) Storage temperature/ Storage humidity–10 °C to +60 °C (14 °F to 140 °F)/20% to 80% (no condensation) Power requirementsVPL-SW636C:100 V to 240 V AC, 3.5 A to 1.6 A, 50/60 Hz VPL-SW631C: 100 V to 240 V AC, 3.4 A to 1.5 A, 50/60 Hz VPL-SW631/SX631: 100 V to 240 V AC, 3.3 A to 1.5 A, 50/60 Hz ItemsDescriptions
86Specifications *1: For details, refer to “Acceptable Input Signals” on page 90. *2: Information on accessories in this manual is current as of January 2016.Power consumptionAC 100 V to 120 VVPL-SW636C: 341W VPL-SW631C: 338W VPL-SW631: 330W VPL-SX631: 305W AC 220 V to 240 VVPL-SW636C: 328W VPL-SW631C: 324W VPL-SW631: 320W VPL-SX631: 294W Power consumption (standby mode)AC 100 V to 120 V0.5 W (when “Standby Mode” is set to “Low”) AC 220 V to 240 V0.5 W (when “Standby Mode” is set to “Low”) Power consumption (networked standby mode)AC 100 V to 120 V 5.3 W (LAN) 5.9 W (optional WLAN module) 6.1 W (all terminals and networks connected) (when “Standby Mode” is set to “Standard”) AC 220 V to 240 V5.6 W (LAN) 6.2 W (optional WLAN module) 6.4 W (all terminals and networks connected) (when “Standby Mode” is set to “Standard”) Heat dissipationVPL-SW636C: 100 V AC: 1,163 BTU/h 240 V AC: 1,119 BTU/h VPL-SW631C: 100 V AC: 1,153 BTU/h 240 V AC: 1,105 BTU/h VPL-SW631: 100 V AC: 1,126 BTU/h 240 V AC: 1,092 BTU/h VPL-SX631: 100 V AC: 1,041 BTU/h 240 V AC: 1,003 BTU/h Standard dimensions (W/H/D)Approx. 372 × 167 × 382 mm (14 21/32 × 6 9/16 × 15 1/32 inches) Approx. 372 × 138 × 382 mm (14 21/32 × 5 7/16 × 15 1/32 inches) (without projecting parts) Mass VPL-SW636C:Approx. 6.3 kg (14 lb) VPL-SW631C: Approx. 6.2 kg (14 lb) VPL-SW631/SX631: Approx. 6.0 kg (13 lb) Supplied accessoriesSee “Checking the Supplied Accessories” in the supplied Quick Reference Manual. Optional accessories *2 *3Projector Lamp LMP-E220 (for replacement) USB wireless LAN module IFU-WLM3 Interactive Pen Device IFU-PN250A/PN250B ItemsDescriptions Notes
87Specifications Others *3: Not all optional accessories are available in all countries and area. Please check with your local Sony Authorized Dealer. Design and specifications of the unit, including the optional accessories, are subject to change without notice.
88Specifications Pin assignment HDMI terminal (HDMI, female)RGB input terminal (Mini D-sub 15-pin, female) RS-232C terminal (D-Sub 9-pin, male) 1 T.M.D.S. Data2+11 T.M.D.S. Clock Shield 2 T.M.D.S. Data2 Shield12 T.M.D.S. Clock – 3 T.M.D.S. Data2 –13 N.C. 4 T.M.D.S. Data1+14 RESERVED (N.C.) 5 T.M.D.S. Data1 Shield15 SCL 6 T.M.D.S. Data1 –16 SDA 7 T.M.D.S. Data0+17 DDC GND 8 T.M.D.S. Data0 Shield18 +5V Power 9 T.M.D.S. Data0 –19 Hot Plug Detect 10 T.M.D.S. Clock+ 1 2 19 18 1 Video input (red) R9Power supply input for DDC 2 Video input (green) G10 GND 3Video input (blue) B11 GND 4 GND 12 DDC/SDA 5 RESERVE 13 Horizontal sync signal 6 GND (R) 14 Vertical sync signal 7 GND (G) 15 DDC/SCL 8 GND (B) 1NC 6NC 2RXDA 7RTS 3TXDA 8CTS 4DTR 9NC 5 GND 5 1 9 6
89Specifications Others USB terminal (Type A, female) USB terminal (Type B, female) 1VBUS (4.4 - 5.25 V) 2 Data– 3 Data+ 4 Ground 1 VCC (+5 V) 2 Data– 3 Data+ 4 Ground
90Specifications Acceptable Input Signals*1 Computer signal Digital TV signal *4 Analog TV signal *1: When a signal other than the signals listed in table is input, the picture may not be displayed properly. An input signal meant for screen resolution different from that of the panel will not be displayed in its original resolution. Text and lines may be uneven. *2: This is identified as a movie delivery signal of 720/60p. *3: This is identified as a movie delivery signal of 1080/60p. *4: Only G with sync/Y is supported. ResolutionfH[kHz]/ fV[Hz]Input terminal RGB/ YPBPRHDMIRGB 640 × 350 31.5/70 zz 37.9/85zz 640 × 400 31.5/70zz 37.9/85zz 640 × 480 31.5/60zzz 35.0/67zz 37.9/73zz 37.5/75zz 43.3/85zz 800 × 600 35.2/56zz 37.9/60zzz 48.1/72zz 46.9/75zz 53.7/85zz 832 × 624 49.7/75zz 1024 × 768 48.4/60zzz 56.5/70zz 60.0/75zz 68.7/85zz 1152 × 864 64.0/70zz 67.5/75zz 77.5/85zz 1152 × 900 61.8/66zz 1280 × 960 60.0/60zzz 1280 × 1024 64.0/60zzz 80.0/75zz 91.1/85zz 1400 × 1050 65.3/60zzz 1600 × 1200 75.0/60zzz 1280 × 768 47.8/60z 1280 × 720 45.0/60z z*2z 1920 × 1080 67.5/60z*3 1366 × 768 47.7/60zzz 1440 × 900 55.9/60zzz 1280 × 800 49.7/60zzz SignalfV[Hz] Input terminal RGB/ YPBPRHDMI 480i 60zz 576i 50zz 480p 60zz 576p 50zz 1080i 60zz 1080i 50zz 720p 60zz 720p 50zz 1080p 60z 1080p 50z SignalfV[Hz]Input terminal VIDEO/S VIDEO NTSC 60z PA L / S E C A M 5 0z Notes ResolutionfH[kHz]/ fV[Hz]Input terminal RGB/ YPBPRHDMIRGB