Sony Projector VPL-SW630 User Manual

51Messages List
Others
Messages List
When any of the messages listed below appears on the projected image, address the problem in 
accordance with the table below.
MessagesMeaning/RemedyPage
High temp.! Lamp off in 
1 min.Check the items below.
 Check if nothing is blocking the ventilation holes.
 Check if the air filter is not clogged.
 Check if the Installation Attitude in the Installation menu is 
set correctly.4, 4, 
29, 56
Frequency is out of 
range!Change the output setting of the connected...

52Troubleshooting
Troubleshooting
Before asking to have the projector repaired, try to diagnose the problem, following the 
instructions below.
SymptomsRemedyPage
The power is not turned 
on. Check if the AC power cord is firmly connected. –
When the “Control Key Lock” is set to “On,” you cannot turn 
on the projector using the 
?/1 key on the projector. 26
If the lamp or lamp cover is not attached securely, the projector 
cannot be turned on. 54
No image. Check if the connecting cable is connected to...

53Troubleshooting
Others
The image is dark/too 
bright.The settings for “Brightness,” “Contrast,” and “Lamp Mode” 
affect brightness of the image. Check if the value is 
appropriate.20, 27
The image will be dark when the lamp is burnt out. Check 
“Lamp Timer,” and replace the lamp with a new one if 
necessary.30, 54
“With Static Signal” is set to “On.”  27
During picture muting, the lamp is dimmed to reduce power 
consumption. 27
When video signal is not input, the lamp is dimmed to reduce 
power...

54Replacing the Lamp
Replacing the Lamp
Replace the lamp with a new one if a message displayed on the projected image (page 51).
Use an LMP-E220 projector lamp (not supplied) for replacement.
 The lamp remains hot after the projector is 
turned off. If you touch the lamp, you may 
burn your finger. When you replace the 
lamp, wait for at least an hour after 
turning off the projector for the lamp to 
cool sufficiently.
 Do not allow any metallic or inflammable 
objects into the lamp replacement slot...

55Replacing the Lamp
Others
4Insert the new lamp all the way in until 
it is securely in place (1). Tighten the 
three screws (2).
5Close the lamp cover and tighten the 
1 screw.
The power will not turn on if the lamp is 
not secured properly.
6Connect the AC power cord to a wall 
outlet and turn on the projector.
7Reset the lamp timer for notification of 
the next replacement time.
Select “Lamp Timer Reset” on the 
Function menu then press the ENTER 
key. When a message appears, select 
“Yes” to reset...

56Cleaning the Air Filter
Cleaning the Air Filter
When a message appears on the projected image indicating time for a filter cleaning, clean the 
air filter (pages 50, 51).
If the dust cannot be removed from the air filter even after cleaning, replace the air filter with 
a new one. For details on a new air filter, consult with qualified Sony personnel.
If you neglect to clean the air filter, dust may accumulate, clogging it. As a result, the 
temperature may rise inside the unit, leading to a possible...

57Cleaning the Air Filter
Others
The air filter consists of 2 filters (A, 
B).
4Reattach the side cover.
Be sure to attach the air filter firmly, 
otherwise it may cause a malfunction.
Note
A
B
A
B 

58Specifications
Specifications
ItemsDescriptions
ModelVPL-SW630/SW620/VPL-SX630
Projection system 3 LCD system
Display device Effective display 
sizeVPL-SW630/SW620: 0.59 inch (15.0 mm), 3 plate 
panels, Aspect ratio 16:10
VPL-SX630: 0.63 inch (16.0 mm), 3 plate panels, Aspect 
ratio 4:3
Effective picture 
elementsVPL-SW630/SW620: 3,072,000 pixels (1280 × 800 
pixels, 3 plate panels)
VPL-SX630: 2,359,296 pixels (1024 × 768 pixels, 3 
plate panels)
Projection lens Zoom Manual (approx.1.03 times)
Focus...

59Specifications
Others
INPUT OUTPUT 
(Computer/video)INPUT ARGB/YPBPR input connector: Mini D-sub 15-pin 
female, G with sync/Y: 1 Vp-p ± 2 dB, sync negative, 
75 ohms terminated, RGB/P
BPR: 0.7 Vp-p ± 2 dB, 
75 ohms terminated, Sync signal: TTL level high 
impedance, positive/negative
Audio input connector: Stereo mini jack, rated input 
500 mVrms, input impedance more than 47 kohms
INPUT BRGB input connector: Mini D-sub 15-pin female, 
RGB: 0.7 Vp-p ± 2 dB, 75 ohms terminated, Sync signal: 
TTL level...

60Specifications
*1: For details, refer to “Acceptable Input Signals” on page 63.
*2: Information on accessories in this manual is current as of March 2014.
*3: Not all optional accessories are available in all countries and area. Please check with your local 
Sony Authorized Dealer.
Design and specifications of the unit, including the optional accessories, are subject to change 
without notice.Power 
consumptionVPL-SW630:
100 V to 120 V AC: 323 W
220 V to 240 V AC: 311 W
VPL-SW620:
100 V to 120 V AC:...