Sony Projector VPL-SW630 User Manual

11Connecting the Projector
Preparation
VIDEO IN 
For connecting video equipment with a video output connector.
INPUT A
For connecting video equipment with a YPBPR output connector.
INPUT C
For connecting video equipment with an HDMI output connector.
 Use HDMI-compatible equipment which has the HDMI Logo. 
 Use a high speed HDMI cable(s) on which the cable type logo is specified. (Sony products are 
recommended.)
 The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital)...

12Connecting the Projector
Microphone ( )
For connecting a microphone.
Only dynamic microphones are supported.
USB connector (Type A) ( )
For connecting a USB memory device (“Using USB Media Viewer” (page 46)).
OUTPUT
Projected images or input audio can be output to display equipment such as a monitor or audio 
equipment such as speakers with a built-in amplifier.
Projected images and audio can be output.
Connecting a microphone
Note
Connecting a USB memory device
Connecting an External Monitor and Audio...

13Projecting an Image
Projecting/Adjusting an Image
BProjecting/Adjusting an Image
Projecting an Image
The size of a projected image depends on the distance between the projector and screen. Install 
the projector so that the projected image fits the screen size. For details on projection distances 
and projected image sizes, see 
“Projection Distance and Lens Shift Range” (page 64).
 Due to the characteristics of ultra short throw projector, the image may appear uneven on a 
projection surface that is...

14Projecting an Image
(Example)
To project image files stored in a USB 
memory device, see “USB Media 
Viewer” (page 46). To play video and 
audio using USB Connection, see 
“Playing Video and Audio using USB 
Connection” (page 44). To use 
Presentation Function via Network, see 
“Presentation Function via Network” 
(page 40).
7Adjust the focus, size and position of 
the projected image (page 15).
Open the side cover, and adjust the lens 
shift dials, focus lever and zoom lever.
Open the side cover
Press...

15Projecting an Image
Projecting/Adjusting an Image
Adjusting the Projected image
Focus Size (Zoom)
Focus 
leverZoom 
lever 

16Projecting an Image
Adjusting the tilt of the projector with the adjusters
You can adjust the height of the projector 
using the adjusters.
By changing the tilt of the projector with 
adjusters, you can adjust the position of the 
projected image.
 Be careful not to let the projector down on your fingers.
 Do not push hard on the top of the projector with the adjuster extended.
Changing the aspect ratio of the projected image
Press the ASPECT key on the remote commander to change the aspect ratio of...

17Projecting an Image
Projecting/Adjusting an Image
Correcting trapezoidal distortion of the projected image (Keystone feature) 
If the image becomes trapezoidal, set the keystone manually. 
1Press the KEYSTONE key on the remote 
commander or select V Keystone in the 
Installation menu. 
2Use the V/v/B/b keys to set the value. The 
higher the value, narrower the top of the 
projected image. The lower the value, the 
narrower the bottom.
 Since the Keystone adjustment is an 
electronic correction, the...

18Projecting an Image
1Press the ?/1 key on the unit or the remote commander.
The projector starts shutdown and turns off. If you press the ?/1 key within 10 seconds 
again, shutdown is cancelled.
Do not turn off the projector soon after the lamp lights. It may cause a malfunction of the lamp 
(does not light ,etc.).
2Unplug the AC power cord from the wall outlet.
To turn off without displaying confirmation message
Press and hold the ?/1 key on the unit for a few seconds (page 51).
ECO gauge
This gauge...

19Using a MENU
Adjustments and Settings Using a Menu
BAdjustments and Settings Using a Menu
Using a MENU
The menu displays used for the explanation below may be different depending on the model you are 
using.
1Press the MENU key to display the 
menu.
2Select the setting menu. 
Use the V/v key to select the setting 
menu then press the b key or ENTER 
key.
3Select the setting item.
Use the V/v key to select the setting 
menu then press the b key or ENTER 
key.
To return to the selection screen of the...

20The Picture Menu
The Picture Menu
The Picture is used to adjust the picture for each input signal.
*1: When a computer signal is input, this option is available.
*2: The settings in the Picture return to their factory defaults, except for Picture Mode.
*3: When a video signal is input, this option is available.
*4: When the signal without color burst signal is input after selecting “Video” or “S-Video”, this 
option is unavailable.
*5: When an analog TV signal is input, this option may not available,...