Sony Projector Vpl Px32 User Manual

11 (GB)
Location and Function of Controls
Control panel
1 VOL +/– keys
Adjust the volume of the built-in speakers and output
level of the AUDIO jack.
+ : Increases the volume.
– : Decreases the volume.
2 Arrow keys (M/m/

12 (GB)
Connector panel
1 INPUT A connectors
1DIGITAL RGB/5BNC/RGB switch: Selects
DIGITAL RGB, 5BNC or RGB on INPUT A
connectors. Select the appropriate position
depending on the input signal.
DIGITAL RGB: Signal input from DIGITAL
RGB connector.
5BNC: Signal input from the 5BNC connector.
RGB: Signal input from the RGB connector.
2RGB input connector (HD D-sub 15-pin,
female): Connects to the monitor output on a
computer using the supplied cable. This
connector only accepts signals from a computer....

13 (GB)
Remote Commander
The keys which have the same names as on the
control panel function identically.
 Note
There may be no LENS key in your Remote Commander.
Moreover, the position of the HELP key and the FREEZE
key on your Remote Commander may differ.
Notes on laser beam
• Do not look into the laser transmitter.
• Do not aim the laser at people.
1 
I / 1 key
2 MUTING keys
Cut off the picture and sound.
PIC: Cuts off the picture. Press again to restore the
picture.
AUDIO: Cuts off the sound from...

14 (GB)
Location and Function of Controls / Installing the Projector
qk MENU/TAB key
Functions as a MENU key.
ql APA (Auto Pixel Alignment) key
w; VOLUME +/– keys
wa LEMS key
This key does not work in the unit.
ws PJ/NETWORK (Projector/Network) selector
switch
Set this switch to PJ always.
wd COMMAND ON/OFF switch
When this switch is set to OFF, no key on the Remote
Commander function. This saves the battery power.
wf Transmission indicator
Lights up when you press a key on the Remote
Commander.
This...

15 (GB)
Connecting
Connecting with a Computer
This section describes how to connect the projector to
a computer.
You can control the projector from your computer by
using USB equipment. For details, see “Using USB
equipment (e.g., USB mouse)”.
Also refer to the instruction manual of equipment to
be connected.
Notes
•This unit accepts the VGA, SVGA, XGA or SXGA
signals. However, we recommend you to set the
output signal of your computer to the XGA.
•If you set your computer, such as a notebook type
IBM...

16 (GB)
Connecting
RS-232C INPLUG IN POWEROUTPUT
INPUT A
INPUT B
VIDEO INCONTROL SREMOTE
DIGITAL RGBUSB
R/R-Y/PRB/B-Y/PBSYNC/HD VD G/YMOUSE AUDIO RGBMOUSE AUDIO AUDIO RGB
MONITOR 
S VIDEO VIDEO AUDIOL
R(MONO)
DIGITAL
RGB RGB
5BNC
DIGITAL
RGB RGB
5BNCRight side
to serial
port or
to mouse
port MonitorMouse cable
SIC-S21
(for serial)(not
supplied)/
S22 (for PS/2)
(supplied)
to
monitor
outStereo audio
connecting
cable (not
supplied)*
to
audio
out
HD D-sub
15-pin
cable
(supplied)
Computer Monitor
cable...

17 (GB)
Connecting
Using USB equipment (e.g., USB mouse)
Connect the USB equipment to the USB connector on
the connector panel.
You can connect your computer to the projector via
the RGB connector, 5BNC connector or DIGITAL
RGB connector.  (The example below uses the RGB
connector.)
On the USB function
When connecting the projector to a computer by
using the USB cable for the first time, the computer
recognizes the following devices automatically.
1USB hub (general use)
2USB human interface device...

18 (GB)
RS-232C INPLUG IN POWEROUTPUT
INPUT A
INPUT B
VIDEO INCONTROL SREMOTE
DIGITAL RGBUSB
R/R-Y/PRB/B-Y/PBSYNC/HD VD G/YMOUSE AUDIO RGBMOUSE AUDIO AUDIO RGB
MONITOR 
S VIDEO VIDEO AUDIOL
R(MONO)
DIGITAL
RGB RGB
5BNC
DIGITAL
RGB RGB
5BNC
Notes
•Set the aspect ratio using ASPECT in the INPUT
SETTING menu according to the input signal.
•To connect a 15k RGB/Component equipment,
select the COMPUTER/COMPONENT/DTV
YP
BPR/DTV GBR in the INPUT-A in the SET
SETTING menu according to the input signal.
•Use the...

19 (GB)
INPUTHELPMENU
ENTERRESETAPALIGHT
VOL +
VOL -
LAMP/
COVERTEMP/
 FANPOWER
SAVINGON/
 STANDBY
2
3
14
5
MUTINGPICAUDIO
LENS
APA
LASER
INPUTD KEYSTONE
HELP
PJ NETWORKON COMMAND
OFF
VOLUME
ENTER
FUNCTION
RM-PJM15
PROJECTOR
D ZOOMCLICKRESET/
ESCAPE
MENU/
TAB
R
1
23
FREEZE
2
3
Projecting
1After all equipment is connected completely, plug
the AC power cord into the wall outlet.
The ON/STANDBY indicator lights in red and the
projector goes into the standby mode.
2Press the I / 1 key.
The ON/STANDBY...

20 (GB)
Projecting
•“ADJUSTING” appears on the screen. Press the
APA key again during the adjustment to restore the
original screen.
•“Complete!” appears on the screen when the picture
is adjusted properly. The picture may not be adjusted
properly depending on the kinds of input signals.
•Adjust the items in the INPUT SETTING menu
when you adjust the picture manually.
For details, see page 24 (GB).
To correct the trapezoid
When the projecting image is a trapezoid, change the
projector’s position/height...