Sony Projector Vpl Fx52 User Manual

11 Location and Function of Controls
Overview
lAdjuster
Use the adjusters to keep the projector 
level if it is installed on an uneven 
surface. 
Adjust the height so that the projector 
becomes level. The projector is raised by 
turning the adjusters clockwise, or it is 
lowered by turning them 
counterclockwise.
mAir filter
For details, see “Cleaning the Air 
Filter” on page 43.
To maintain optimal performance, clean 
the air filter periodically.
aLENS CONTROL key
Enters the focus, zoom or shift...

 12Location and Function of Controls
bArrow keys (M/m/

13 Location and Function of Controls
Overview
hENTER key
Enters the settings of items in the menu 
system.
iRESET key
Resets the value of an item back to its 
factory preset value. This key functions 
when the menu or a setting item is 
displayed on the screen.
aINPUT A connectors (HD D-sub 
15-pin, female)
Connects to the monitor output on a 
computer. 
bINPUT B connector (RGB (DVI)) 
(DVI-D)
Connects to a computer equipped with 
DVI (digital) output connector with a 
DVI cable.
cINPUT C connectors
5BNC...

 14Location and Function of Controls
eVIDEO IN connectors
Connect to external video equipment 
such as a VCR.
S VIDEO (mini DIN 4-pin): Connects 
to the S video output (Y/C video 
output) on video equipment.
VIDEO (BNC type): Connects to the 
composite video output.
fTRIG (trigger output) jack 
(monaural minijack)
The signal is transmitted from this jack 
to the connected equipment whether the 
projector is on or off. (This is not a 
power source for external equipment.) 
Approximately 12 V DC signal is...

15 Location and Function of Controls
Overview
e (Memory Stick) key
This key does not work in the unit.
fFREEZE key
This key freezes the projected image.  
Press again to unfreeze the image. 
(available for computer signals only)
gAIR SHOT key
This key does not work in the unit.
8Keys that emulate a mouse
This key does not work in the unit.
iENTER key
jFUNCTION 1/2/3 keys
This key does not work in the unit.
kStrap holder
Attaches a strap.
lCONTROL S OUT jack (stereo 
mini-jack)
Connects to the CONTROL S...

 16Location and Function of Controls
Battery installation
1Push and slide to open the lid, then 
install the two size AA (R6) batteries 
(supplied) with the correct polarity.
2Replace the lid.
Notes on batteries
 Make sure that the battery orientation is 
correct when inserting batteries.
 Do not mix an old battery with a new one 
or different types of batteries. 
 If you will not use the Remote 
Commander for a long time, remove the 
batteries to avoid damage from battery 
leakage. If batteries have...

17 Installation Example
Setting Up and Projecting
BSetting Up and Projecting
Installation Example
 The following table indicates an example of installing the standard lens 
supplied with VPL-FX52.
 When you use VPL-FX52L (Lens are not supplied), be sure refer to the 
operating instructions of Installation Manual for Dealers.
 
To calculate the installation measurement (unit: mm)
SS: screen size diagonal (inches)
a (minimum) = {(SS × 50.127/1.3102) – 73.9} × 1.025
a (maximum) = {(SS × 64.519/1.3102) –...

 18Connecting the Projector
Connecting the Projector
When you connect the projector, make sure to:
 Turn off all equipment before making any connections.
 Use the proper cables for each connection.
 Insert the cable plugs firmly; loose connections may increase noise and 
reduce performance of picture signals. When pulling out a cable, be sure to 
pull it out from the plug, not the cable itself.
This section describes how to connect the projector to a computer or video 
equipment.
For more information,...

19 Connecting the Projector
Setting Up and Projecting
 When connecting a Macintosh1) computer equipped with video output connector of a 
type having two rows of pins to the connector, use a commercially available plug 
adaptor.
Note
INPUT C
R/R-Y/PRINPUT A
RGB
NEWTWORK
B/B-Y/PBG/Y SYNC/HD
MONITOR OUTVIDEO IN
VIDEO OUTS VIDEO VIDEOTRIG
RS-232C
PLUG IN POWERCONTROL S
VD
INPUT B
DV I - D
Video cable (not supplied)
to monitor out Front of the projector
HD D-sub 15-pin 
(not supplied)to S video
output DVI...

 20Connecting the Projector
  
 When you connect the unit to a video GBR output connector, select video GBR or 
component with the Input-C Signal Sel. setting in the SET SETTING menu.
 Use the composite sync signal when you input the external sync signal from video 
GBR/component equipment. 
To connect to a video GBR/Component equipment
Notes
INPUT C
R/R-Y/PRINPUT A
RGB
NEWTWORK
B/B-Y/PBG/Y SYNC/HD
MONITOR OUTVIDEO IN
VIDEO OUTS VIDEO VIDEOTRIG
RS-232C
PLUG IN POWERCONTROL S
VD
INPUT B
DV I - D
Monitor...