Sony Projector VPL-FHZ60 User Manual

							51
Cleaning the Air 
Filter
When the message that prompts cleaning the 
air filter appears, clean the air filter.
If the dust cannot be removed from the air 
filter even after cleaning, replace the air filter 
with a new one.
For details on a new air filter, consult with 
qualified Sony personnel.
If you continue to use the projector even 
after the message is displayed, dust may 
accumulate, clogging it. As a result, the 
temperature may rise inside the unit, 
leading to a possible malfunction or fire.
1Turn off the projector and disconnect 
the AC power cord from a wall outlet.
2Slide the lock switch on the side cover 
toward UNLOCK to unlock the cover. 
3Slide the side cover downward by 
pushing out its upper corners to 
remove the side cover.
4Loosen the screws (four) and pull out 
the filter cover by pinching the grab on 
the left side.
5Pull out the air filter from the main 
unit.
Caution
Side cover
Lock switchesFilter cover Screws
Grab
Air filter 
						

							52
6Clean the air filter with a vacuum 
cleaner.
7Replace the air filter and attach the 
filter cover.
When attaching the filter cover, fit the 
two tabs on the right into place, turn the 
filter cover using the right side as an 
axis, and fit the two tabs on the left into 
place. Then, tighten the four screws.
8Fit the two tabs on the side cover into 
place and slide the side cover upward.
9Lock the side cover.
Be sure to attach the air filter firmly; the power 
cannot be turned on if it is not attached 
securely.
Replacing the 
Projection Lens
 Avoid removing/attaching the lens with the 
projector installed suspended from a ceiling.
 For usable projection lenses, see “Optional 
accessories” (page 56).
 Do not attach any lens other than the 
specified accessory lens sold separately.
 Be careful not to drop the projection lens.
 Avoid touching the lens surface.
1Return the projection lens to the center 
position.
While the unit is turned on, press the 
LENS SHIFT button on the Remote 
Commander, then press the RESET 
button on it. The projection lens returns 
to the center position.
The projection lens cannot be removed 
unless it has returned to the center position.
2Turn off the projector, then unplug the 
AC power cord from the wall outlet.
When replacing the lens, your eyes may 
be damaged if a strong light accidently 
gets into your eyes. Before replacing the 
lens, turn off the projector and then 
unplug the AC power cord.
3While pressing and holding down the 
LENS RELEASE button, rotate the Note
Ta b s
Ta b s
Tabs
Notes
Removing
Note
Caution 
						

							53
projection lens counterclockwise to 
pull out the lens straight.
1Fully insert the projection lens with 
the index on the lens facing toward the 
top surface of the main unit.
2Rotate the lens clockwise until it 
clicks.
When attaching the projection lens, do not 
press the LENS RELEASE button.
Attaching
LENS RELEASE 
buttonProjection lens
Top of surface of the main unit 
Index
Note 
						

							54
Specifications
ItemDescription
Model nameVPL-FHZ65/VPL-FHZ60
Display system 3 LCD system
Display device Size of effective 
display area0.76 (19.3 mm) × 3, Aspect ratio 16:10
Number of pixels 6,912,000 (1920 × 1200 × 3) pixels
Light source Laser diode
Light output VPL-FHZ65: 6,000 lm (when “Light Output Mode” is 
set to “High”)
VPL-FHZ60: 5,000 lm (when “Light Output Mode” is 
set to “High”)
Displayable 
scanning 
frequency
*1
Horizontal: 15 kHz to 92 kHz, Vertical: 48 Hz to 92 Hz
Display resolution Computer signal 
inputMaximum display resolution: 1920 × 1200 dots
Panel display resolution: 1920 × 1200 dots
Video signal 
inputNTSC, PAL, SECAM, 480/60i, 576/50i, 480/60p, 576/
50p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/60p, 
1080/50p, 1080/24p
Color system NTSC
3.58, PAL, SECAM, NTSC4.43,  PA L - M ,  PA L - N ,  
PA L 6 0
Computer and 
video signal input/
outputINPUT ARGB/YP
BPR input terminal: Mini D-sub 15-pin 
female, G with sync/Y: 1 Vp-p ± 2 dB, sync negative, 75 
ohms terminated, RGB/P
BPR: 0.7 Vp-p ± 2 dB, 75 ohms 
terminated, Sync signal: TTL level high impedance, 
positive/negative
Audio input terminal: Stereo mini jack, rated input 
500 mVrms, input impedance more than 47 kilohms
INPUT BDVI-D input terminal: DVI-D 24-pin (Single link), DVI 
1.0 compliant, HDCP support
Audio input terminal: Shared with INPUT A
INPUT CHDMI input connector: HDMI 19-pin, digital RGB/
YP
BPR, HDCP support, HDMI audio support
INPUT DHDBaseT terminal: RJ45
HDBaseT transmittable signal: HDMI (Video, Audio), 
RS-232C, Ethernet (100BASE-TX)
HDBaseT LAN cable: STP type (CAT5e or higher, 
straight, not supplied), Maximum length: 100 m
VIDEO INVideo input terminal: BNC, 1 Vp-p ± 2 dB, sync 
negative, 75 ohms terminated
Audio input terminal: Shared with INPUT A 
						

							55
OUTPUT AMONITOR output terminal: Mini D-sub 15-pin 
female, G with sync/Y: 1 Vp-p ± 2 dB, sync negative, 75 
ohms terminated, RGB/P
BPR: 0.7 Vp-p ± 2 dB, 75 ohms 
terminated, Sync signal: HD, VD 4 V (open), 1 Vp-p (75 
ohms), positive/negative
Audio output terminal: Stereo mini jack,  stereo, 1 
Vrms (maximum volume, when inputting 500 mVrms), 
output impedance 5 kilohms
OUTPUT BDVI-D output terminal: DVI-D 24-pin (Single link), 
DVI 1.0 compliant, non-HDCP compliant
Control signal 
input/outputRS-232C terminal: D-Sub 9 pin male
LAN terminal: RJ45, 10BASE-T/100BASE-TX
CONTROL S input terminal (DC power supply): 
Stereo mini jack, 5 Vp-p, Plug in power DC 5 V
Operating 
temperature/
Operating 
humidity0 °C to 40 °C (32 °F to 104 °F)/20% to 80% (no 
condensation)
Storage 
temperature/
Storage humidity–10 °C to +60 °C (14 °F to +140 °F)/ 20% to 80% (no 
condensation)
Power required VPL-FHZ65: AC 100 V to 240 V, 5.5 A to 2.3 A, 50/60 
Hz
VPL-FHZ60: AC 100 V to 240 V, 4.5 A to 1.9 A, 50/60 
Hz
Power 
consumptionAC 100 V to 
120 VVPL-FHZ65: 509 W
VPL-FHZ60: 420 W
AC 220 V to 
240 VVPL-FHZ65: 492 W
VPL-FHZ60: 408 W
Power 
consumption 
(Standby Mode)AC 100 V to 
120 VVPL-FHZ65: 0.5 W (when “Standby Mode” is set to 
“Low”)
VPL-FHZ60: 0.5 W (when “Standby Mode” is set to 
“Low”)
AC 220 V to 
240 VVPL-FHZ65: 0.5 W (when “Standby Mode” is set to 
“Low”)
VPL-FHZ60: 0.5 W (when “Standby Mode” is set to 
“Low”)
ItemDescription
Model nameVPL-FHZ65/VPL-FHZ60 
						

							56
The values for mass and dimensions are approximate.
*1: For details, refer to “Acceptable Input Signals” on page 59.Power 
consumption 
(Networked 
Standby Mode)AC 100 V to 
120 VVPL-FHZ65: 15.0 W (LAN), 15.0 W (HDBaseT), 15.0 
W (All Terminals and Networks Connected)
(when “Standby Mode” is set to “Standard”)
VPL-FHZ60: 15.0 W (LAN), 15.0 W (HDBaseT), 15.0 
W (All Terminals and Networks Connected)
(when “Standby Mode” is set to “Standard”)
AC 220 V to 
240 VVPL-FHZ65: 13.3 W (LAN), 13.3 W (HDBaseT), 13.3 
W (All Terminals and Networks Connected)
(when “Standby Mode” is set to “Standard”)
VPL-FHZ60: 13.3 W (LAN), 13.3 W (HDBaseT), 13.3 
W (All Terminals and Networks Connected)
(when “Standby Mode” is set to “Standard”)
Heat dissipation AC 100 V to 
120 VVPL-FHZ65: 1732 BTU/h
VPL-FHZ60: 1433 BTU/h
AC 220 V to 
240 VVPL-FHZ65: 1679 BTU/h
VPL-FHZ60: 1393 BTU/h
Outside 
dimensions460 × 175 × 515 mm (18 
1/8 × 6 7/8 × 20 9/32) (W/H/
D)
460 × 169 × 515 mm (18 
1/8 × 6 21/32 × 20 9/32)  (W/H/
D) (without protrusions)
Mass VPL-FHZ65: Approx. 16 kg (34 lb)
VPL-FHZ60: Approx. 16 kg (34 lb)
Supplied 
accessoriesSee “Checking the Supplied Accessories” in the supplied 
Quick Reference Manual.
Optional 
accessories
*2 *3Projection Lens VPLL-3007: Manual focus, Projected 
image size: 60 to 300 (1.52 m to 7.62 m), Maximum 
external dimensions (W × H × D): 150 × 150 × 222 mm 
(5 
29/32 × 5 29/32 × 8 3/4), Mass: 1.7 kg (3.7 lb 60 oz)
Projection Lens VPLL-Z3009: Manual focus/zoom, 
Projected image size: 60 to 300 (1.52 m to 7.62 m), 
Maximum external dimensions (W × H × D): 150 × 150 
× 217 mm (5 
29/32 × 5 29/32 × 8 19/32), Mass: 1.7 kg 
(3.7 lb 60 oz)
Projection Lens VPLL-Z3024: Electric focus/zoom, 
(when attaching to this projector), Projected image size: 
40 to 600 (1.02 m to 15.24 m), Maximum external 
dimensions (W × H × D): 97 × 105 × 177 mm (3
13/16 × 
49/64 × 631/32), Mass: 1.2 kg (2.6 lb 42 oz)
Projection Lens VPLL-Z3032: Electric focus/zoom, 
(when attaching to this projector), Projected image size: 
40 to 600 (1.02 m to 15.24 m), Maximum external 
dimensions (W × H × D): 97 × 105 × 177 mm (3
13/16 × 
49/64 × 631/32), Mass: 1.2 kg (2.6 lb 42 oz)
Notes
ItemDescription
Model nameVPL-FHZ65/VPL-FHZ60 
						

							57
*2: Not all optional accessories are available in all countries and area. Please check with your local 
Sony Authorized Dealer.
*3: Information on accessories in this manual is current as of July 2015.
Design and specifications of the unit, including the optional accessories, are subject to change 
without notice. 
						

							58
Pin assignment
DVI-D terminal (DVI-D, female)RGB input terminal (Mini D-sub 15-
pin, female)
RS-232C terminal (D-Sub 9-pin, male)
1 T.M.D.S.
Data2–14 +5 V Power
2 T.M.D.S.
Data2+15 Ground (return 
for +5 V)
3 T.M.D.S.
Data2 Shield16 Hot Plug 
Detect
4 NC 17 T.M.D.S.
Data0–
5 NC 18 T.M.D.S. 
Data0+
6 DDC Clock 19 T.M.D.S. 
Data0 Shield
7 DDC Data 20 NC
8NC 21NC
9 T.M.D.S.
Data1–22 T.M.D.S. 
Clock Shield
10 T.M.D.S.
Data1+23 T.M.D.S.
Clock+
11 T.M.D.S.
Data1 Shield24 T.M.D.S. 
Clock–
12 NC
13 NC
18
16
9
17
24
1 Video input 
(red) R9 Power supply 
input for DDC
2 Video input 
(green) G10 GND
3 Video input
(blue) B11 GND
4 GND 12 DDC/SDA
5 RESERVE 13 Horizontal sync 
signal
6 GND (R) 14 Vertical sync 
signal
7 GND (G) 15 DDC/SCL
8 GND (B)
1NC 6NC
2RXDA 7RTS
3TXDA 8CTS
4DTR 9NC
5 GND 
						

							59
HDMI terminal (HDMI, female)
Acceptable Input Signals
Computer signal
1 T.M.D.S.
Data2+11 T.M.D.S.
Clock Shield
2 T.M.D.S.
Data2 Shield12 T.M.D.S.
Clock–
3 T.M.D.S.
Data2–13 NC
4 T.M.D.S.
Data1+14 RESERVED 
(N.C.)
5 T.M.D.S.
Data1 Shield15 SCL
6 T.M.D.S.
Data1–16 SDA
7 T.M.D.S.
Data0+17 GND
8 T.M.D.S.
Data0 Shield18 +5V Power
9 T.M.D.S.
Data0–19 Hot Plug 
Detect
10 T.M.D.S.
Clock+
ResolutionfH [kHz]/
fV [Hz]
Input terminal
INPUT AINPUT B/ 
INPUT C/ 
INPUT D
640 × 350   31.5/70 
z–
37.9/85 
z–
640 × 400 31.5/70 
z–
37.9/85 
z–
640 × 480 31.5/60 
zz
35.0/67 z–
37.9/73 
z–
37.5/75 
z–
43.3/85 
z–
800 × 600 35.2/56 z–
37.9/60 
zz
48.1/72 z–
46.9/75 
z–
53.7/85 
z–
832 × 624 49.7/75 
z–
1024 × 768 48.4/60 
zz
56.5/70 z–
60.0/75 
z–
68.7/85 
z–
1152 × 864 64.0/70 
z–
67.5/75 
z–
77.5/85 
z–
1152 × 900 61.8/66 
z–
1280 × 960 60.0/60 
zz
75.0/75 z–
1280 × 1024 64.0/60 
zz
80.0/75 z–
91.1/85 
z–
1400 × 1050 65.3/60 
zz
1600 × 1200 75.0/60 zz
1280 × 768 47.8/60 zz
1280 × 720 45.0/60 zz*2
1920 × 1080 67.5/60  –z*2
1366 × 768 47.7/60 zz
1440 × 900 55.9/60 zz
1680 × 1050 65.3/60 zz
1280 × 800 49.7/60 zz
1920 × 1200 74.0/60 z*1z*1
1600 × 900 60.0/60 z*1z*1
ResolutionfH [kHz]/
fV [Hz]
Input terminal
INPUT AINPUT B/ 
INPUT C/ 
INPUT D 
						

							60
Video signal
*1: Available for VESA Reduced Blanking 
signals only.
*2: INPUT B is determined as a computer 
signal; INPUT C/INPUT D is determined 
as a video signal.
 When a signal other than the signals listed in 
table is input, the picture may not be 
displayed properly.
 An input signal meant for screen resolution 
different from that of the panel will not be 
displayed in its original resolution. Text and 
lines may be uneven.
 Some actual value may differ slightly from 
the design values given in the table.
SignalfV [Hz]
Input terminal
VIDEOINPUT AINPUT B/ 
INPUT C/ 
INPUT D
NTSC 60
z––
PA L /
SECAM50
z––
480i 60 –
zz
576i 50 –zz
480p 60 –zz
576p 50 –zz
1080i 60 –zz
1080i 50 –zz
720p 60 –zz*2
720p 50 –zz
1080p 60 – –z*2
1080p 50 – –z
1080p 24 – –z
Notes