Sony Projector VPL-FHZ60 User Manual

							21
Press the RESET key to restore the 
projected image before adjustment.*1
When correcting deflection on the 
top/bottom sides of the image
1Move x using V/v/B/b to select the 
side you want to correct.
2Press the ENTER key.
The cursor appears.
3Adjust the deflection of the side, using 
V/v/B/b.
You can adjust the center point of 
deflection using B/b. For the range of 
deflection, use V/v. You can adjust the 
top/bottom independently.Press the RESET key to restore the 
projected image before adjustment.
*1
*1: The setting may not be reset depending on 
the combination of adjustment values of 
the Screen Fitting setting items. In this 
case, reset all of the Screen Fitting setting 
items.
1Install the projectors.
Input a pattern, etc., to adjust the 
projected positions from multiple 
projectors.
2Set the ID mode.
Set a different ID mode for each 
projector (page 31). 
3Set the picture mode. 
Set the picture mode of the multiple 
projectors to “Multi Screen” (page 24).
4Unify the color space. 
Set the color space of the multiple 
projectors to the same mode (Custom 1 
to 3) (page 35). R/G/B can be finely 
adjusted as necessary.
Adjust using this cursor
Note
Blending Projections from 
Multiple Projectors on a 
Screen 
						

							22
5Adjust the color matching setting.
Finely adjust each tone as necessary 
(page 35).
6Set the Edge Blending setting.
When overlaying multiple projections, 
the Edge Blending setting is available.
Select “Multi Screen” in the Installation 
menu, then select “Edge Blending” 
(page 35).
7Enable the Edge Blending function.
In “Blend Settings,” set “Edge 
Blending” to “On” for each blending 
position.
8Set the blending width.
Set the blending width according to the 
overlapping range for the source signal.
9Adjust using “Blend Fitting.”
Finely adjust the overlapped area.
10Adjust using “Zone Black Level Adj.”
Adjust each correction zone by “Zone 
Black Level Adj.” for the most uniform 
black level between each zone. 
During this adjustment, a black image is 
automatically projected.
 Depending on the blending start position or 
the blending width, the menu may overlap 
with the blending area and become invisible. 
If you want to operate the projector while 
viewing the menu, set “Edge Blending” to 
“Off” once and make adjustments. Then, set 
“Edge Blending” to “On.” The procedure shown above is for general 
guidance. Your own installation may vary 
according to the situation.
 When multiple projectors are set up in a line, 
the temperature inside the projectors may 
increase due to exhaust vent proximity, and 
an error indication may result.
In this case, space the projectors farther apart 
and/or install deflection partitioning between 
them.
For more details, consult with qualified Sony 
personnel.
1Press the ?/1 key on the main unit or 
the 1 key on the Remote Commander.
The projector starts shutdown and turns 
off. 
2Unplug the AC power cord from the 
wall outlet.
Notes
Assign the width here.
Turning Off the Power 
						

							23
BAdjustments and Settings Using a Menu
Using a Menu
The menu displays used for the explanation 
below may be different depending on the 
model you are using.
1Press the MENU key to display the 
menu.
2Select the setting menu. 
Use the V or v key to select the setting 
menu, then press b or ENTER key.
3Select the setting item.
Use the V or v key to select the setting 
menu, then press b or ENTER key.
To return to the selection screen of the 
setting menu, press the B key or the 
RETURN key.
4Make the setting or adjustment for the 
selected item. 
Menu operation differs depending on the 
setting item. If the next menu window is 
displayed, select the item according to 
the operations in step 3 and then press 
the ENTER key to register the setting.To return to the selection screen of the 
setting items, press the B key or the 
RETURN key. Also, to reset the setting 
value of an item to its factory preset 
value, press the RESET key during 
setting or adjusting.
Using a pop-up menu
Press the V/v/B/b key to select an item. 
Press the ENTER key to register the 
setting. The previous screen is restored.
Using the setting menu 
Press the V or v key to select the item. 
Press the ENTER key to register the 
setting. The previous screen is restored.
Using the adjustment menu
To increase the number, press the V or b 
key and to decrease the number, press 
the v or B key. Press the ENTER key to 
register the setting. The previous screen 
is restored. 
5Press the MENU key to clear the 
menu.
The menu disappears automatically if no 
key is pressed for a while.
Note
Setting menu
Setting items
Audio Output Vol.
Smart APA Standard
CC Display
Background Blue
Start Up Image  On
All Reset 
 
Sel Set Back
Function
On
Off
Selecting items
Adjust Back
Contrast
Min
80Max 
						

							24
The Picture Menu
For adjusting the picture for each input signal.
Setting items Description
Picture ModeDynamic: Emphasizes the contrast to produce a “dynamic” picture.
Standard: Makes the picture be natural and well balanced.
Brightness Priority: Makes the picture bright to suit a bright environment.
Multi Screen: Optimizes the picture quality to suit projecting using multiple 
projectors.
Reset The picture settings are initialized to their factory preset values.
However, “Picture Mode” and “Custom 1,” “Custom 2,” “Custom 3,” and 
“Custom 4” of “Color Temp.” do not return to the factory preset values.
Contrast The higher the setting, the greater the contrast. The lower the setting, the lower 
the contrast.
Brightness The higher the setting, the brighter the picture. The lower the setting, the darker 
the picture.
Color The higher the setting, the greater the intensity. The lower the setting, the lower 
the intensity.
Hue The higher the setting, the more greenish the picture becomes. The lower the 
setting, the more reddish the picture becomes.
Color Temp.9300K/7500K/6500K: The higher the temperature, the more bluish the picture. 
The lower the temperature, the more reddish the picture.
Brightness Priority: Projects images at the maximum brightness.
Custom 1/ Custom 2/ Custom 3/ Custom 4: An adjusted color temperature 
setting can be stored for each item.
The factory settings are Custom 1: 9300K, Custom 2: 7500K, Custom 
3: 6500K, Custom 4: Brightness Priority.
Sharpness The higher the setting, the sharper the picture. The lower the setting, the softer 
the picture.
Light Settings
Dynamic 
ControlOn/Off: Brightness is adjusted automatically according to image content. Dark 
images are projected with brightness adjusted, leading to energy-saving. Bright 
images are projected brightly, without adjusting brightness.
Light 
Output 
ModeAdjusts brightness of the light source.
High: The image becomes brighter, and power consumption becomes higher.
Standard: Power consumption becomes lower; however, the image will be 
darker.
Extended: The images becomes dark but extended projection is enabled.
Custom: You can adjust brightness as prefer.
Constant 
Brightness 
*1
On/Off: Available when Light Output Mode is set to “High” or “Standard.” 
Brightness is constant at about 75% of light output of each mode. 
						

							25
*1: The projector may not be able to maintain the brightness in an environment with a lot of dust and 
dirt. Expert Setting
Reality 
CreationAdjusts the detail and noise processing of images. (Super-resolution function)
On: Adjusts the settings of “Reality Creation.”
Resolution: When you increase the setting value, the texture and detail of the 
image become sharper.
Noise Filtering: When you increase the setting value, the noise (picture 
roughness) becomes less prominent.
Test: On/Off: Switches “On” and “Off” at a certain frequency to check the 
effect of “Reality Creation.” *2
Off: The “Reality Creation” function is not applied.
Contrast 
EnhancerCorrects the level of bright and dark parts automatically to optimize contrast 
according to a scene. Increases image sharpness and makes image dynamic.
High/Middle/Low: You can adjust the contrast enhancer.
Off: The “Contrast Enhancer” function is not applied.
Gamma 
Mode2.2: Equivalent to a 2.2 gamma curve.
2.4: Equivalent to a 2.4 gamma curve.
Gamma 3: Applies a gamma curve that prioritizes the brightness to suit use in 
a relatively bright environment.
Gamma 4: Enhances black and white contrast to suit use in a relatively dark 
environment.
DICOM GSDF Sim.
*3: Gamma setting is in accordance with the Grayscale 
Standard Display Function (GSDF) of the Digital Imaging and 
Communications in Medicine (DICOM) standards.
Color 
SpaceConverts the color space.
Custom 1: Produces images with vivid colors.
Custom 2: Produces images with muted colors.
Custom 3: Reproduces image colors true to the original image source.
You can select R/G/B for the selected color space and adjust the R/G/B 
chromaticity points in the x and y directions in the CIExy chromaticity diagram 
respectively.
Color Select: Select the color to adjust from “Red,” “Green,” and “Blue.”
Cyan - Red (x): Adjusts the chromaticity point of the selected color toward 
cyan-red (x).
Magenta - Green (y): Adjusts the chromaticity point of the selected color 
toward magenta-green (y).
Color 
CorrectionOn: Adjusts the hue, saturation, and brightness for the selected color. Repeat 
steps 1 and 2 described below to specify the target color.
1Press V/v to select “Color Select,” then press B/b to select the color you 
want to adjust among “Red,” “Yellow,” “Green,” “Cyan,” “Blue,” and 
“Magenta.”
2Press V/v to select “Hue,” “Saturation” or “Brightness,” then adjust them 
to suit your taste using B/b while watching the projected picture.
Off: The “Color Correction” function is not applied.
Film 
Mode
*4 *5Au to : Precisely reproduces the image from a film source to suit the original 
film source. Normally, select this option.
Off: Select this option if the images are rough around the edges when “Auto” is 
selected.
Notes
Setting items Description 
						

							26
*2: The display position of the status during the test works together with the “Menu Position” setting 
(page 31).
*3: Available when a computer signal is input from the DVI-D input terminal (INPUT B), HDMI 
input terminal (INPUT C), or HDBaseT input terminal (INPUT D). This projector is not to be 
used as a device for medical diagnosis.
*4: When a video signal is input, this option is available.
*5: When a progressive signal is input, this option is not available. 
						

							27
The Screen Menu
For adjusting the size, position, and aspect ratio of the projected image for each input signal.
*1:  Note that if the projector is used for profit or for public viewing, modifying the original picture 
by switching to the aspect mode may constitute an infringement of the rights of authors or 
producers, which are legally protected.
 Depending on the input signal or “Screen Aspect” setting, setting items for aspect ratio or 
some other setting items cannot be set in some cases, or changing the aspect ratio setting may 
have no effect.
 A part of the image may be displayed in black, depending on the setting item. Setting items Description
Aspect
*1Changes the aspect ratio of the projected image (page 29).
When the 
computer 
signal is 
inputFull 1: Displays the image to fit the maximum projected image size without 
changing the aspect ratio of the input signal.
Full 2: Displays the image to fit the maximum projected image size.
Normal: Displays the image on the center point of the projected image 
without changing the resolution of the input signal or enlarging the image.
When the 
video signal 
is input4:3: Displays the image to fit the maximum projected image size with an 
aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size with an 
aspect ratio fixed to 16:9.
Full: Displays the image to fit the maximum projected image size.
Zoom: Display the center point of the projected image to zoom.
V Center
*2 *3Adjust the whole projected image by moving up and down on the screen. 
As the selected number increases, the screen moves up, and as the selected 
number decreases, the projected image moves down.
Vertical Size
*2 *3Reduces or enlarges the image vertically.
The projected image is enlarged as the setting increases and reduced as the 
setting decreases. If the subtitle of a movie, etc. cannot be seen, use this 
together with “V Center.”
Overscan
*2On/Off: Hides the outline of the image when set to “On.”  Select “On” if 
noise appears along the edge of the image.
Adjust Signal
*6Adjusts the image of a computer signal. Use this item if the edge of the 
image is cut and reception is bad.
APA
*4 *5Automatically adjusts the projected image to an optimum quality when you 
press the ENTER key.
Phase
*4Adjusts the dot phase of the display pixel and the input signal. Set to the 
value where looks clearest.
Pitch
*4The higher the setting, the wider the horizontal image elements (pitch). The 
lower the setting, the narrower the horizontal image elements (pitch).
Shift
*6H: The higher the setting, the farther right the image is projected on the 
screen. The lower the setting, the image farther left.
V: The higher the setting, the farther up the image is projected on the screen. 
The lower the setting, the image farther down.
Notes 
						

							28
*2: Available when a video signal is input from the RGB/YPBPR input terminal (INPUT A), DVI-D 
input terminal, HDMI input terminal, and HDBaseT terminal.
*3: Available when “Aspect” is “Zoom” and “Screen Aspect” is 16:10 or 16:9.
*4: Available when a computer signal is input from the RGB/YP
BPR input terminal (INPUT A).
*5: If the projected image includes a large amount of black portion around it, the APA function will 
not work properly and a part of the image may not be displayed on the screen. In addition, an 
optimum image cannot be obtained, depending on the type of input signal. In this case, adjust 
the “Phase,” “Pitch,” and “Shift” items manually.
*6: Available when a computer or video signal is input from the RGB/YP
BPR input connector 
(INPUT A). This option is available only when “Aspect” is set to “Zoom.” 
						

							29
Aspect
*1: If you select “Normal,” the image is 
projected in the same resolution as the 
input signal without changing the aspect 
ratio of the original image.
*2: If you select “Full 2,” the image is 
projected to fit the projected image size, 
regardless of the aspect ratio of the image.
*3: Depending on the input signal, the 
projected image may be projected as 
illustrated below. In this a case, select 
“16:9.”
*4: Depending on the input signal, the image 
may be projected as illustrated below. In 
this a case, select “Zoom.”
*5: If you select “Full,” the image is projected 
to fit the projected image size, regardless 
of the aspect ratio of the image. Input signal Recommended 
setting value and 
projected image
Computer signal
(4:3) (Full 1)*1 *2
(16:9) (Full 1)*1 *2
(16:10) (Full 1)*1
Video signal
(4:3) (4:3)*3 *5
(16:9) (16:9)*4 *5 
						

							30
The Function Menu
The Function menu is used for setting various functions of the projector.
*1: Executes APA when a computer signal is input via the RGB/YPBPR input terminal (INPUT A).
*2: When using the Twin Picture display mode and there is no input signal, the background will be 
black even if you set this item to “Image”. Setting items Description
Audio Output Vol. The higher the setting, the higher an audio level output from the audio 
output terminal. The lower the setting, the lower the audio level.
Smart APAOn/Off: When set to “On,” executes APA automatically when a signal is 
input.
*1
CC DisplayCC1/CC2/CC3/CC4/Text1/Text2/Text3/Text4: Select the closed caption 
service (Captions or Text).
Off: Closed caption does not appear.
Background
*2Blue/Black/Image: Sets the background for when there is no input signal. 
When set to “Image,” the Start Up Image is displayed.
Start Up ImageOn/Off: When set to “On,” the Start Up Image is displayed on the screen 
upon startup of the projector.
All Reset All settings are initialized to their factory preset values.
Notes