Sony Projector VPL-FHZ60 User Manual

41
Entered values will not be applied unless 
you click on [Apply].
1Click on [Owner information] to enter 
the owner information recorded in the 
e-
mail report.
2Set the timing of the e-mail report.
Click on [Advanced Menu] to display 
the [E-mail] button, then click on [E-
mail] to open the E-mail page.
Maintenance Reminder: Set the timing 
for maintenance. To reset 
Maintenance Reminder, check the 
RESET check box and then click on 
[Apply].
3Enter the outgoing e-mail address in 
the Email Address...

42
Set the LAN network function on the Setup 
page.
Entered values will not be applied unless 
you click on [Apply].
1Click on [Network] to open the 
Network page.
2Set the items for internet protocol.
(a) Setting the IPv4 address
Obtain an IP address automatically: 
Automatically provides the network 
settings by a DHCP server function, 
such as the router. The IP Address, 
Subnet Mask, Default Gateway, 
Primary DNS, and Secondary DNS 
display the values provided by a 
DHCP server. 
Specify an IP...

43
Change the settings for the control protocol 
on the Setup page. Entered values will not be 
applied unless you click on [Apply].
1Click on [Advanced Menu] to display 
the buttons for more settings.
2(a) Set Advertisement.
Start Advertisement Service: 
Set Advertisement to enabled or 
disabled. Items for Advertisement are 
enabled only when this function is 
enabled. The function is disabled at the 
factory default.-Community: 
Input the community name for 
Advertisement and PJ Talk. If the 
community...

44
disabled. The password is the same as 
that of the Web page administrator.
-Port No.: Input the server port of 
ADCP. The factory default setting is 
“53595.”
-Timeout: Input the time (minutes) until 
ADCP communication is terminated in 
case it is disconnected. The factory 
default setting is “60.”
-Host Address: Input the IP address that 
the ADCP server is allowed to receive. If 
no IP address is input, receiving 
commands will be allowed from any IP 
address. From the moment the IP 
address is...

45
(e) Set the system service.
Start DDDP Service:
Set DDDP to enabled or disabled. For 
details, refer to the DDDP specifications 
in the reference from AMX Corporation. 
The function is disabled at the factory 
default. 
Crestron Control:
For details, refer to the specifications in 
product catalogues, etc., from Crestron 
Corporation.
-IP Address:
Input the Crestron system server.
-IP ID:
Input the IP ID for the CIP protocol.
-Port No.:
Input the port number for the CIP 
protocol server.
(f) Reset the...

46
BOthers
Indicators
You can check the projector status or abnormality by checking the lighting/flashing status of 
the ON/STANDBY indicator and WARNING indicator on the front. If the indicators flash in 
red, address the problem in accordance with “Warning indicators and remedies” (page 47). 
Operating status indication 
Indicator statusOperating statusMeaning
Standby The power is supplied to the projector and the 
projector is in a standby mode according to the 
setting.
Warm-up The projector is...

47
Warning indicators and remedies
If the indicators flash in a manner other than described above, unplug the AC power cord and 
make sure the ON/STANDBY indicator turns off, then plug the AC power cord into the wall 
outlet and turn on the projector.
If the problem still persists, consult with qualified Sony personnel.
Indicator statusThe number of
flashesMeaningRemedies
Twice The side cover or air 
filter is not installed 
securely.Check how the side cover or 
air filter is attached and 
install it...

48
Messages List
When any of the messages listed below appears on the projected image, address the problem in 
accordance with the table below.
MessageMeaning/RemedyPage
Clean the filter.
Projector temperature is 
high.
Switching to High 
Altitude Mode.Temperature in the projector has increased.
As a countermeasure against use at an altitude of 1,500 m or 
higher, set “High Altitude Mode” to “On.”
If you are not using the projector at a high altitude, perform the 
remedies below and set “High Altitude...

49
Troubleshooting
Before asking to have the projector repaired, try to diagnose the problem, following the 
instructions below.
SymptomRemedyPage
The power is not turned 
on.Check if the AC power cord is firmly connected. –
When the “Control Key Lock” is set to “On,” you cannot turn 
on the projector using the ?/1 key on the projector.31
Check how the air filter is attached and install it securely. 51
No image. Check if the connecting cable is connected to external 
equipment properly.9
Check if the...

50
The image is dark/too 
bright.The settings for “Brightness,” “Contrast,” and “Light Output 
Mode” affect brightness of the image. Check if the value is 
appropriate.24
“With Static Signal” is set to “On.”  34
When video signal is not input, the light is dimmed to reduce 
power consumption.33
When the temperature around the unit is high, the brightness 
will be reduced to protect the unit.–
The image is not clear. Check if the projector is in focus. 18
The picture will not be clear if condensation has...