Sony Projector VPL-FH65 User Manual

31
The Function Menu
The Function menu is used for setting various functions of the projector.
*1: Executes APA when a computer signal is input via the RGB/YPBPR input terminal (INPUT A).
*2: When using the Twin Picture display mode and there is no input signal, the background will be 
black even if you set this item to “Image”. Setting items Description
Audio Output Vol. The higher the setting, the higher an audio level output from the audio 
output terminal. The lower the setting, the lower the audio...

32
The Operation Menu
The Operation menu is used for setting for the operations by using the menu or the Remote 
Commander.
*1: When “All Off” is selected, warning message for high temperature is not displayed.
*2: Note that Sony is not liable for failure of the unit or any accident caused by selecting “All Off.”Setting items Description
Language Selects the language used in the menu and on-screen displays.
Menu PositionBottom Left/Center: For selecting the position of the menu displayed on the...

33
*3: You will not be able to use the projector if you forget your password. If you call qualified Sony 
personnel because you have forgotten the password, you will be asked to verify the projector’s 
serial number and your identity. (This process may differ in other countries/regions.) Once your 
identity has been confirmed, we will provide you with the password. 

34
The Connection/Power Menu
The Connection/Power menu is used for setting for the connections and power.
Setting items Description
Network Setting
IPv4 Setting
IP Address SetupAuto(DHCP): The IP address is assigned automatically from the 
DHCP server such as a router.
Manual: To specify the IP Address manually.
IP Address/ Subnet 
Mask/ Default 
Gateway/Primary 
DNS/Secondary 
DNSWhen “Manual” is selected for “IP Address Setup,” select the item 
with the B or b key and input the value with V or v key....

35
*1: When connecting via HDBaseT, only the 100BASE-TX can be used for connection. When using 
the LAN terminal of the main unit, you can connect with the 10BASE-T/100BASE-TX.
*2: The IP addresses when using HDBaseT and when using the LAN terminal should be set 
respectively.
 Setting the IP address when using a LAN via HDBaseT.
Set “LAN Setting” to “via HDBaseT” in “HDBaseT Settings,” then set the IP address in 
“Network Setting.”
 Setting the IP address when using the LAN terminal.
Set “LAN Setting”...

36
The Installation Menu
The Installation menu is used for installing the projector.
Setting items Description
Screen Fitting Adjusts the distortion of the projected image that occurs due to installation 
conditions or when a portion of the image spreads beyond the screen.
*1
Wa r p i n g : Select an adjustment point and move it vertically/horizontally to 
adjust the image distortion.
V Keystone: Adjusts the vertical keystone distortion. The higher the 
setting, the narrower the upper side of the...

37
Blend 
SettingsConfigure the Edge Blending setting for the top, bottom, right, and left of 
the screen respectively. 
Left/Right/Top/Bottom: Set the Edge Blending effect for each position. 
Edge Blending: Set “On” to set “Blending Range” or “Blend Start Pos.” 
Blending Range: Set the width where images are overlapped. 
Blend Start Pos.: Set the start position from which images are 
overlapped.
Blend Cursor: Displays the cursors at the start and end positions for edge 
blending. When set to “On,” the...

38
*1: Since the Keystone/Warping/Linearity adjustment is an electronic correction, the image may 
deteriorate.
*2: Depending on the position adjusted with the lens shift feature, the aspect ratio of the image may 
change from the original or projected image may be distorted with Keystone adjustment.
*3: The brightness and color of the projected image may not match completely, even after you adjust 
“Brightness” and “Color.”
*4: You cannot adjust anything other than the targeted adjustment zones in “Zone...

39
The Information Menu
The Information menu is used to check projector status, such as total usage time of the lamp.
*1: These items may not be displayed depending on the input signal.Items Description
Model Name Displays the model name.
Serial No. Displays the serial number.
fH / fV (horizontal 
frequency/vertical 
frequency)
*1
Displays the horizontal frequency/vertical frequency/signal type of the 
current input signal.
Lamp Timer Indicates the total usage time of a lamp.
Note 

40
BNetwork
Using Network 
Features
Connection to the network allows you to 
operate the following features:
 Checking the current status of the 
projector via a Web browser.
 Remotely controlling the projector via a 
Web browser.
 Receiving the e-mail report for the 
projector.
 Making the network settings for the 
projector.
 Supports network monitoring and control 
protocol (Advertisement, ADCP, PJ Talk, 
PJ Link, SNMP, AMX DDDP [Dynamic 
Device Discovery Protocol], Crestron 
RoomView).
 When...